Engine Oil Pump
Show/hide table
Illustration 1 | g02807758 |
(1) Rotor |
Show/hide table
Clearance between inner and outer rotor (New) | |
Allowable Clearance | |
Show/hide table
Illustration 2 | g03421438 |
(2) Pump Body |
Show/hide table
Clearance between outer rotor and pump body (New) | |
Allowable clearance | |
- Put a strip of Plastigage on the rotor face with grease.
- Install the cover and tighten the bolts.
- Remove the cover carefully.
- Measure the width that Plastigage becomes flat with the scale to get the oil clearance.
Show/hide table
Table 3 Clearance between inner rotor and cover (New) 0.105 mm (0.00414 inch) to0.150 mm (0.00590 inch) Allowable clearance 0.20 mm (0.008 inch) - If the clearance is more than the allowable limit, replace the rotor assembly of the oil pump.
Show/hide table
Illustration 3 | g02807823 |
(3) Plastigage |
Caterpillar Information System:
2011/12/23 A New Routing Is Used on Fuel Injector Wiring Harnesses on C9.3 Industrial Engines {1290, 1408, 1900}
3516C and C175-16 Engines Selective Catalytic Reduction SCR Module Differential Pressure Is Low
3516C and C175-16 Engines Selective Catalytic Reduction SCR Module Differential Pressure Is High
2011/12/23 A New Bolt and Washers Are Used in the Damper Guard Group of Certain C18 Marine Engines {1205, 7553}
2011/12/23 Proper Measurement for O-Ring Seal Land of Water-Cooled Exhaust Elbows on Certain Commercial Engines {1061}
C18 Generator Set Engine Oil Level Gauge - Calibrate
UPS 120, UPS 150, UPS 250 and UPS 300 Uninterruptible Power Supplies UPS View Software
UPS 120, UPS 150, UPS 250 and UPS 300 Uninterruptible Power Supplies Specifications
3516C and C175-16 Engines Selective Catalytic Reduction Air Assist Pressure Is Low
3516C and C175-16 Engines Selective Catalytic Reduction Air Assist Pressure Is High
UPS 120, UPS 150, UPS 250 and UPS 300 Uninterruptible Power Supplies System Description
UPS 120, UPS 150, UPS 250 and UPS 300 Uninterruptible Power Supplies Model View Illustrations
3512C and 3516C Marine Propulsion Engines Diagnostic Trouble Codes
C1.7, C1.8 and C2.4 Tier 4 Interim and EU Stage 3A Engines for Caterpillar Built Machines Cylinder Block
3512C and 3516C Marine Propulsion Engines Event Codes
Procedures For Using: 127-8781 Transfer Filter Cart , old 9U-7361 (110V, 60 hz), 169-7159 Transfer Filter Cart , old 127-8782 (220V, 50 hz) CE, 174-9158 Transfer Filter Cart , old 129-0849 (Air Motor Driven){0374, 0599, 0680, 0738} Procedures For Using: 127-8781 Transfer Filter Cart , old 9U-7361 (110V, 60 hz), 169-7159 Transfer Filter Cart , old 127-8782 (220V, 50 hz) CE, 174-9158 Transfer Filter Cart , old 129-0849 (Air Motor Driven){0374, 0599, 0680, 0738}
UPS 120, UPS 150, UPS 250 and UPS 300 Uninterruptible Power Supplies Modem
UPS 120, UPS 150, UPS 250 and UPS 300 Uninterruptible Power Supplies Ethernet Interface
320 GC, 320 and 323 Excavator Machine Systems Specifications Bucket Linkage
Procedure for Using 173-8839 Fluid Storage Filter Cart {0113, 0374, 0599, 0680, 0738, 7579} Procedure for Using 173-8839 Fluid Storage Filter Cart {0113, 0374, 0599, 0680, 0738, 7579}
3516B Engine for the MT4400D Off-Highway Truck Water Lines
3512C and 3516C Industrial Engines Turbocharger Oil Lines
3516B Engine for the MT4400D Off-Highway Truck Turbocharger Oil Lines
3512C and 3516C Industrial Engines Turbocharger