Caterpillar O-rings: Measuring Tool, Material Application, and Dash Size Cross Reference{0374, 0599, 0759, 0767, 7555} Caterpillar

Caterpillar Products: All

Introduction

Important Safety Information

Illustration 1	g02139237
Think Safety

European Union Compliant, CE marked

Most accidents that involve product operation, maintenance, and repair are caused by failure to observe basic safety rules or precautions. An accident can often be avoided by recognizing potentially hazardous situations before an accident occurs. A person must be alert to potential hazards. This person should also have the necessary training, skills, and tools to perform these functions properly.

Improper operation, lubrication, maintenance, or repair of this product can be dangerous and could result in injury or death.

Do not operate or perform any lubrication, maintenance, or repair on this product until you have read and understood the Tool Operating Manual.

Safety precautions and warnings are provided in this manual and on the product. If these hazard warnings are not heeded, bodily injury or death could occur to you or to other persons.

The hazards are identified by the "Safety Alert Symbol" and followed by a "Signal Word" such as "DANGER", "WARNING", or "CAUTION". The Safety Alert "WARNING" label is shown below.

A non-exhaustive list of operations that may cause product damage are identified by "NOTICE" labels on the product and in this publication.

Caterpillar cannot anticipate every possible circumstance that might involve a potential hazard. The warnings in this publication and on the product are, therefore, not all inclusive. If a tool, procedure, work method, or operating technique that is not recommended by Caterpillar is used, the operator must be sure that the procedures are safe. The operator must also be sure that the product will not be damaged or made unsafe by any unspecified procedures.

The information, specifications, and illustrations in this publication are based on information that was available at the time that the publication was written. The specifications, torques, pressures, measurements, adjustments, illustrations, and other items can change at any time. These changes can affect the service that is given to the product. Obtain the complete and most current information before you start any job.

When replacement parts are required for this product Caterpillar recommends using Caterpillar replacement parts or parts with equivalent specifications including, but not limited to, physical dimensions, type, strength, and material.

Literature Information

This manual contains safety information, operation instructions and maintenance information and should be stored with the tool group

Some photographs or illustrations in this publication may show details that can be different from your service tool. Guards and covers might have been removed for illustrative purposes.

Continuing improvement and advancement of product design might have caused changes to your service tool, which are not included in this publication.

Whenever a question arises regarding your service tool or this publication, consult Dealer Service Tools (DST) for the latest available information.

Safety Section

The Safety section lists basic safety precautions.

Read and understand the basic precautions listed in the Safety section before operating or performing maintenance and repair on this service tool.

General Information Section

The General Information section describes tooling functions and features. The section provides useful information on individual parts, additional tooling, and resources.

Operation Section

The Operation section is a reference for the new operator and a refresher for the experienced operator.

Photographs and illustrations guide the operator through correct procedures for using the tool group.

Operating techniques outlined in this publication are basic. Skill and techniques develop as the operator gains knowledge of the service tool and the tools capabilities.

Maintenance Section

The Maintenance section is a guide to tool inspection, cleaning, storage, and tool disposal

Service Parts Section

The Service Parts section is a reference for parts identification and available part numbers.

Safety Icon Nomenclature

Personal Protection/Important Information

Illustration 2	g02166423
Personal Protection/Important Information

Prohibited Action

No smoking

Hazard Avoidance

Crushing hazard (foot)

Crushing hazard (hand)

Pinch point

Fire hazard

Electrical Shock - Hazard

Fire hazard

General Information

Introduction

Parts countermen, parts and service salesmen, and shop and field servicemen will benefit from the information in this publication. This publication includes:

• Basic information on Caterpillar O-rings

• Description of the 9U-5155 O-ring Measuring Tool , designed to identify SAE industry standard O-ring dash sizes

• O-ring material selection for given applications (Sections ""Attachment B-1" " through ""Attachment B-10" ")

• Cross reference listing of SAE industry standard dash sizes and Caterpillar O-ring part numbers (Sections ""Attachment B-1" " through ""Attachment B-10" ")

• Cross reference listing of SAE industry standard dash sizes and Caterpillar backup ring part numbers (Sections ""Attachment C-1" " through ""Attachment C-5" ".)

• List of O-ring kits

Sections ""Attachment A-1" " through ""Attachment A-37" " lists O-rings by cross-section diameter. The material type is included for each part number. Special comments or exceptions to the product colors are shown in Sections ""Attachment B-1" " through ""Attachment B-10" ", Material Description.

Note: The two cross reference lists are not intended to replace the Caterpillar machine or engine parts books. Lists are intended to aid parts countermen, parts and service salesman, and shop and field serviceman in locating O-rings for non-Cat equipment.

Additional Contact Information

For additional product support questions concerning this tool, contact the Caterpillar Dealer Service Tools Hotline at:

USA: 1-800-542-8665, Option 1International:: 1-309-578-7372

How to Use the Charts in Attachments A, B and C

1. Be sure that you have a thorough understanding of the information about O-rings in this manual.

2. Determine the inside diameter and cross-section diameter of the desired O-ring. Use the 9U-5155 O-ring Measuring Tool if necessary.

3. Determine if there is a Caterpillar O-ring with the required dimensions (See Sections ""Attachment A-1" " through ""Attachment A-37" ").

4. If there is a Caterpillar O-ring with the required dimensions, compare the material characteristics shown in Sections ""Attachment B-1" " through ""Attachment B-10" " with the intended use of the replacement O-ring. DO NOT USE the selected O-ring if there is any doubt about O-rings suitability for intended use.

General O-ring Information

An O-ring is a circular-shaped object which has a round cross section. The O-ring is made of elastomer. Elastomer is any natural or synthetic material with the ability to return to original shape after being distorted. The O-ring is used as a seal when installed in a cavity or gland (usually within metal) to prevent the passage of fluid.

To provide a good O-ring seal, four factors must be considered:

1. The diameter of the O-ring cross section

2. The inside diameter of the O-ring

3. The O-ring material

4. Installation technique

Each of these factors will be addressed.

O-ring Diameter Dimensions

Illustration 3	g02795761

To find a replacement O-ring, the Caterpillar part number must be identified. If the number is no longer legible on the part, the O-ring must be measured. An O-ring is measured by the cross section diameter (width) and the inside diameter. (See Figure 3.)

A document (Aerospace Standard AS568A) published by the Society of Automotive Engineers (SAE) established industry standard O-ring dimensions referred to as dash sizes. The dash size is a three-digit number with the first digit indicating the dash series. There are five common industry standard dash series: -0, -1, -2, -3 and -4. Every O-ring in a particular dash series has the same cross section diameter (width).

Table 1

Dash Series	Cross Section Diameter or Width
-0	1.78 mm (0.070 inch)
-1	2.62 mm (0.103 inch)
-2	3.53 mm (0.139 inch)
-3	5.33 mm (0.210 inch)
-4	6.99 mm (0.275 inch)

The second two digits of the dash size give an indication of the size of the O-rings inside diameter. These two numbers do not give the exact dimensions of the inside diameter. However, as the inside diameter of the O-ring becomes larger, so do these two digits. For example, when comparing O-rings with dash sizes of -214 and -225, both O-rings have the same cross section diameter or width 3.53 mm (0.139 inch), but the -225 O-ring as a larger inside diameter.

A Caterpillar tool, the 9U-5155 O-ring Measuring Tool , is available to identify SAE industry standard O-ring dash sizes. Use this tool to determine an O-ring SAE dash size, and then refer to the SAE Dash Size Cross Reference List (Sections ""Attachment A-1" " through ""Attachment A-37" ") to identify the proper Caterpillar part number.

A sixth dash size series (-9xx) is also used to identify the O-rings used with internal straight thread fluid connectors. A significant difference between the -9 series and the -0 through -4 series is that both the cross section and inside diameter of the -9 series increase with an increase in the second and third digits. The measuring cone cannot be used to identify this series.

Caterpillar Non-Metric O-ring Measuring Tool

Illustration 4	g02795767

The 9U-5155 O-Ring Measuring Cone is a tool designed to measure non-metric industry standard O-ring dimensions (cross section and dash size). These dimensions, established in document Aerospace Standard AS568A, are published by the Society of Automotive Engineers (SAE).

Parts countermen and servicemen will find this tool invaluable in determining the dash size of non-metric O-rings. It may also be sold to customers or provided as a promotional item.

Durable as well as economical, the cone-shaped tool is made of high-impact, yellow plastic and is approximately 457 mm (18.0 inch) tall. The round base has five industry standard O-ring cross section diameters (widths) cut into the edge. The cone has 65 steps indicating varying inside diameters.

Before using the O-ring measuring cone, refer to the explanation of O-ring dash sizes in Section ""O-ring Diameter Dimensions" ".

Illustration 5	g02795774

To determine the cross section diameter of an O-ring, insert the O-ring into the slots located around the base of the cone, see Figure 6. The dash series is identified by the column of numbers imprinted on the cone directly above the slot in which the O-ring fits snugly.

Illustration 6	g02795775

Illustration 7	g02795776

Next, drop the O-ring over the peak of the cone, Figure, ensuring that the ring sets level on one of the cones steps. Determine the dash size by reading the dash size column located above the slot identifying the O-ring cross section diameter (width). The number imprinted on the face of the step on which the O-ring rests (you may have to move the O-ring to read the number) identifies the three-digit dash size (fig 7).

Note: To get an accurate reading, the O-ring must fit snugly onto the step, but must not be forced onto the step. An O-ring may be close to a standard dash size, but in reality, may be slightly larger, or slightly smaller, than a "standard size".

The Caterpillar O-ring part number can now be located quickly and easily by dash size in the Dash Size Cross Reference List (Sections ""Attachment A-1" " through ""Attachment A-37" ").

O-Ring Material Selection

The chemical makeup of the O-rings give each seal certain desirable characteristics. Choosing the proper material for a specific application is largely a matter of making the best possible match between O-ring material capabilities and application requirements.

Caterpillar offers several O-ring materials that are applicable in different temperatures, pressure, and media. Sections ""Attachment B-1" " through ""Attachment B-10" " describes the O-ring materials to use in a specific machine system application. If more than one material is applicable, the material and application description provides information to help select the most appropriate material for the application. The following general guidelines should always be followed when matching O-ring material capabilities with applications.

• Never use an O-ring of unknown material as it could cause catastrophic damage to machine components.

• The temperature of the application should be considered when selecting an O-ring material.

• If a lubricant is used to hold the O-ring in place or to make installation easier, be sure that it is compatible with the O-ring material. Usually the system fluid is the best lubricant to use as the O-ring material must be compatible with this fluid.

Note: All of the materials listed in Sections ""Attachment B-1" " through ""Attachment B-10" " are broad "generic" specifications encompassing many formulations, each one "fine-tuned" for specific applications. Some of the formulations used for Caterpillar O-rings are special for Caterpillar, and are not available as "off the shelf" O-rings. Make your selection of material based on the requirements of the particular application.

O-ring Installation

The use of a seal pick is recommended for installing O-rings to eliminate the twisting that occurs during installation. The 5P-1720 Seal Pick can be used for removal and installation of all types of O-rings. One end of the pick is pointed for prying out flexible seals. The blunt, hook end is used to align the seal for installation and to eliminate twisting.

As mentioned in Section ""O-ring Material Selection" ", if a lubricant is used to hold the O-ring in place or to make installation easier, be sure that the lubricant is compatible with the O-ring material. Usually the system fluid is the best lubricant to use as the O-ring material must be compatible with this fluid.

Note: Silicone oil or grease must not be used as a lubricant on a silicone seal during installation.

Caterpillar O-ring Kits

Caterpillar offers a comprehensive selection of commonly needed O-rings in conveniently packaged kits. Most of the kits are refillable and currently represent a 20% savings when compared to buying the O-rings individually. The kits are great for field and shop servicemen, as well as for owners/operators doing repairs. There are six O-ring kits, one D-ring kit, and one metal-backed seal kit.

Table 2

Part No	Kit Description
4C-4782	Contains 580 round cross section nitrile O-rings (32 sizes). For use with Code 61 flange hose couplings, O-ring face seal, and straight thread O-ring hose couplings and adapter fittings.
4C-4784	Contains 80 round rectangular cross section nitrile O-rings (9 sizes). For use with flange couplings (for XT-5 and XT-6 hose).
4C-4786	Contains 85 round cross section nitrile O-rings (7 sizes). For servicing air conditioning systems.
4C-4788	Contains 125 round cross section nitrile O-rings (10 sizes). For use with metric couplings and adapter fittings.
4C-5859	Contains 120 round cross section nitrile O-rings (8 sizes). For use with O-ring face seal couplings and adapter fittings.
4C-8253	Contains 149 round cross section silicone O-rings (32 sizes). For use with Code 61 flange couplings and for static service in high temperature engine and transmission systems.
9S-3135	Contains 60 round cross section nitrile O-rings (6 sizes). For use with Code 61 flange couplings.
9S-3138	Contains 28 metal-backed seals (6 sizes). For use with metal-backed seal couplings. (Metal-backed seals in this kit are in the process of being replaced with rectangular cross section nitrile D-rings.)

Attachment A-1

Table 3

O-RINGS (BY CROSS SECTION)
Dash Size (AS568A)	Section Dia (mm)	Inside Dia. (mm)	Part Number	Material Name	Color
	1.02	10.03	6V-3693	Nitrile (90)
	1.09	45.00	6V-1556	Fluorocarbon (FKM) (90)	DK Green
	1.09	64.06	6V-1555	Fluorocarbon (FKM) (90)	DK Green
	1.35	11.63	1P-8116	Nitrile (75)
	1.40	6.70	085-8219	Nitrile (75)
	1.40	25.63	9X-7430	Fluorocarbon (FKM) (90)	DK Blue
	1.42	3.99	5P-9262	Fluorocarbon (FKM) (75)
	1.42	4.47	9X-7379	HNBR (72)	Orange
	1.42	4.47	5P-6458	Nitrile (75)
-901	1.42	4.70	7M-0105	Nitrile (75)
-901	1.42	4.70	3S-2912	Silicone (70)
	1.50	5.00	8C-3131	Fluorocarbon (FKM) (75)
	1.50	8.00	3E-4296	Nitrile (90)
	1.50	8.20	8T-7876	Nitrile (90)
	1.50	8.20	8C-3076	Fluorocarbon (FKM) (90)	DK Green
	1.50	12.00	9X-7377	Fluorocarbon (FKM) (75)
	1.57	12.70	5D-0834	Nitrile (75)
	1.57	15.88	4M-6582	Nitrile (70)
	1.57	31.04	2M-8663	Nitrile (75)
	1.59	10.72	8M-8544	Nitrile (75)
	1.60	13.10	8C-3097	Nitrile (75)
	1.60	14.00	8C-3132	Fluorocarbon (FKM) (75)
-902	1.63	6.07	8T-9587	EPDM (70)
-902	1.63	6.07	4J-7533	Nitrile (90)
-902	1.63	6.07	5P-7812	Fluorocarbon (FKM) (75)
-903	1.63	7.65	8K-0001	EPDM (70)
-903	1.63	7.65	7J-0204	Nitrile (90)
-903	1.63	7.65	5P-7813	Fluorocarbon (FKM) (75)
	1.65	14.50	8C-3082	Fluorocarbon (FKM) (90)	DK Green
-005	1.78	2.57	8C-3095	Fluorocarbon (FKM) (75)
-006	1.78	2.90	6H-9691	Nitrile (75)
-007	1.78	3.68	3H-0442	Nitrile (75)
-008	1.78	4.47	8F-7219	Nitrile (75)
-008	1.78	4.47	6V-5722	Nitrile (90)
-008	1.78	4.47	8M-8468	Silicone (70)
-008	1.78	4.47	8T-2360	Urethane (90)	Natural
-009	1.78	5.28	8F-9538	Nitrile (75)

Attachment A-2

Table 4

O-RINGS (BY CROSS SECTION)
Dash Size (AS568A)	Section Dia (mm)	Inside Dia. (mm)	Part Number	Material Name	Color
-009	1.78	5.28	3G-1209	Nitrile (90)
-009	1.78	5.28	8M-5250	Silicone (70)
-009	1.78	5.28	8T-2361	Urethane (90)	Natural
-010	1.78	6.07	2D-6392	Nitrile (75)
-010	1.78	6.07	6V-5586	Nitrile (90)
-010	1.78	6.07	3L-6768	Silicone (70)
-010	1.78	6.07	1P-7363	Urethane (90)	Natural
-011	1.78	7.65	9X-7380	HNBR (72)	Orange
-011	1.78	7.65	5F-9144	Nitrile (75)
-011	1.78	7.65	3E-6760	Nitrile (90)
-011	1.78	7.65	4J-5477	Nitrile (90)
-011	1.78	7.65	8C-3085	Nitrile (90)
-011	1.78	7.65	061-7538	Fluorocarbon (FKM) (75)
-011	1.78	7.65	9X-7680	Fluorocarbon (FKM) (90)	DK Green
-012	1.78	9.25	6D-7128	EPDM (70)
-012	1.78	9.25	1H-1023	Nitrile (75)
-012	1.78	9.25	6V-8397	Nitrile (90)
-012	1.78	9.25	5H-8853	Silicone (70)
-012	1.78	9.25	8L-2779	Fluorocarbon (FKM) (75)
-012	1.78	9.25	033-6039	Fluorocarbon (FKM) (90)
-013	1.78	10.82	9X-7381	HNBR (72)	Orange
-013	1.78	10.82	6M-5062	Nitrile (75)
-013	1.78	10.82	095-1750	Nitrile (90)
-013	1.78	10.82	7X-4800	Silicone (70)
-013	1.78	10.82	033-5879	Fluorocarbon (FKM) (75)
-013	1.78	10.82	9X-7409	Fluorocarbon (FKM) (90)	DK Blue
-014	1.78	12.42	9X-7408	HNBR (72)	Orange
-014	1.78	12.42	4K-2039	Nitrile (75)
-014	1.78	12.42	6V-8398	Nitrile (90)
-014	1.78	12.42	033-6033	Fluorocarbon (FKM) (75)
-014	1.78	12.42	6V-5758	Fluorocarbon (FKM) (90)
	1.78	12.83	5P-8942	Fluorocarbon (FKM) (75)
	1.78	13.34	008-5593	Nitrile (75)
-015	1.78	14.00	9X-7382	HNBR (72)	Orange
-015	1.78	14.00	5L-4758	Nitrile (75)
-015	1.78	14.00	095-1751	Nitrile (90)
-015	1.78	14.00	5P-6620	Silicone (70)
-015	1.78	14.00	033-6043	Fluorocarbon (FKM) (90)

Attachment A-3

Table 5

O-RINGS (BY CROSS SECTION)
Dash Size (AS568A)	Section Dia (mm)	Inside Dia(mm)	Part Number	Material Name	Color
-016	1.78	15.60	6V-5138	EPDM (70)
-016	1.78	15.60	4D-2297	Nitrile (75)
-016	1.78	15.60	8C-3086	Nitrile (90)
-016	1.78	15.60	8L-2746	Fluorocarbon (FKM) (75)
-016	1.78	15.60	6V-5142	Fluorocarbon (FKM) (90)
	1.78	15.72	7J-9108	Nitrile (90)
-017	1.78	17.17	9X-7383	HNBR (72)	Orange
-017	1.78	17.17	1S-8947	Nitrile (75)
-017	1.78	17.17	6V-8399	Nitrile (90)
-017	1.78	17.17	2P-2975	Fluorocarbon (FKM) (75)
-018	1.78	18.77	8M-8997	Nitrile (75)
-018	1.78	18.77	8C-3087	Nitrile (90)
-018	1.78	18.77	5P-9757	Fluorocarbon (FKM) (75)
	1.78	18.94	6V-9746	Nitrile (90)
-019	1.78	20.35	6V-6580	Nitrile (90)
-019	1.78	20.35	03-36044	Fluorocarbon (FKM) (75)
-019	1.78	20.35	5E-9816	Fluorocarbon (FKM) (90)	DK Green
-020	1.78	21.95	030-4605	Nitrile (75)
-020	1.78	21.95	8J-2413	Nitrile (90)
-020	1.78	21.95	061-8341	Urethane (90)	Natural
-020	1.78	21.95	5P-5599	Fluorocarbon (FKM) (75)
-021	1.78	23.52	8C-3098	Nitrile (75)
-021	1.78	23.52	8C-3088	Nitrile (90)
-021	1.78	23.52	106-9586	Fluorocarbon (FKM) (75)
-021	1.78	23.52	8C-3093	Fluorocarbon (FKM) (90)
	1.78	23.66	5K-9090	Nitrile (90)
-022	1.78	25.12	5L-4759	Nitrile (75)
-022	1.78	25.12	6V-9178	Fluorocarbon (FKM) (75)
-022	1.78	25.12	8T-9529	Fluorocarbon (FKM) (90)
-023	1.78	26.70	9X-7384	HNBR (72)	Orange
-023	1.78	26.70	077-3241	Nitrile (75)
-023	1.78	26.70	005-8592	Nitrile (90)
-023	1.78	26.70	033-6032	Fluorocarbon (FKM) (75)
-024	1.78	28.30	003-8137	Nitrile (75)
-024	1.78	28.30	4K-4986	Nitrile (90)
-024	1.78	28.30	5P-5600	Fluorocarbon (FKM) (75)
-025	1.78	29.87	6V-0894	Nitrile (75)
-025	1.78	29.87	2Y-2347	Nitrile (90)

Attachment A-4

Table 6

O-RINGS (BY CROSS SECTION)
Dash Size (AS568A)	Section Dia. (mm)	Inside Dia. (mm)	Part Number	Material Name	Color
-025	1.78	29.87	5P-6436	Silicone (70)
	1.78	30.01	6V-8400	Nitrile (90)
-026	1.78	31.47	8F-0212	Nitrile (75)
-026	1.78	31.47	8C-0563	Fluorocarbon (FKM) (90)
-027	1.78	33.05	5D-8539	Nitrile (75
-027	1.78	33.05	8T-4827	Nitrile (90)
-027	1.78	33.05	5P-5601	Fluorocarbon (FKM) (75)
-028	1.78	34.65	5D-6543	Nitrile (75)
-028	1.78	34.65	5K-5221	Nitrile (90)
-028	1.78	34.65	5P-4932	Silicone (70)
-028	1.78	34.65	5P-9658	Fluorocarbon (FKM) (75)
-028	1.78	34.65	8T-7431	Fluorocarbon (FKM) (90)	DK Blue
	1.78	37.98	8T-0315	Nitrile (90)
-030	1.78	41.00	3J-9015	Nitrile (75)
-030	1.78	41.00	5K-6526	Nitrile (90)
-031	1.78	44.17	3P-1979	Nitrile (75)
-031	1.78	44.17	5K-0227	Nitrile (90)
-031	1.78	44.17	5P-7914	Silicone (70)
-031	1.78	44.17	5E-8767	Fluorocarbon (FKM) (75)
-032	1.78	47.35	5K-0216	Nitrile (90)
-032	1.78	47.35	5P-8907	Silicone (70)
-032	1.78	47.35	5E-8768	Fluorocarbon (FKM) (75)
-033	1.78	50.52	6V-0895	Nitrile (75)
-034	1.78	53.70	3P-5859	Silicone (70)
-036	1.78	60.05	077-5843	Nitrile (75)
-036	1.78	60.05	095-1753	Nitrile (90)
-037	1.78	63.22	3P-0815	Silicone (70)
-037	1.78	63.22	7X-4745	Fluorocarbon (FKM) (75)
-039	1.78	69.57	2P-5820	Silicone (70)
-040	1.78	72.76	9J-5686	Nitrile (90)
	1.78	75.46	7C-0565	Polyacrylate (75)
-041	1.78	75.92	6V-3865	Fluorocarbon (FKM) (75)
	1.78	78.56	5P-3114	Silicone (70)
-042	1.78	82.27	5P-2931	Nitrile (75)
-042	1.78	82.27	6V-5778	Fluorocarbon (FKM) (75)
-043	1.78	88.62	8T-2944	EPDM (70)
-043	1.78	88.62	5P-3881	Nitrile (75)
-043	1.78	88.62	8T-6717	Fluorocarbon (FKM) (75)

Attachment A-5

Table 7

O-RINGS (BY CROSS SECTION)
Dash Size (AS568A)	Section Dia. (mm)	Inside Dia. (mm)	Part Number	Material Name	Color
-044	1.78	94.97	7X-9372	Nitrile (75)
-044	1.78	94.97	5E-8769	Fluorocarbon (FKM) (75)
-045	1.78	101.32	7X-5494	Nitrile (75)
-045	1.78	101.32	8T-2572	Silicone (70)
-045	1.78	101.32	6V-1320	Fluorocarbon (FKM) (75)
-046	1.78	107.67	9X-7357	Nitrile (90)
-048	1.78	120.37	8C-5237	Nitrile (75)
	1.78	124.40	9X-7365	Fluorocarbon (FKM) (75)
-049	1.78	126.72	3E-6799	Fluorocarbon (FKM) (75)
-050	1.78	133.07	5P-4969	Silicone (70)
-050	1.78	133.07	6V-1934	Fluorocarbon (FKM) (75)
	1.78	142.34	5P-9650	Silicone (70)
	1.78	193.37	9S-6929	Silicone (70)
	1.78	228.83	1S-7390	Silicone (70)
-904	1.83	8.92	6V-9027	EPDM (70)
-904	1.83	8.92	9X-7378	HNBR (72)	Orange
-904	1.83	8.92	3J-7354	Nitrile (90)
-904	1.83	8.92	6V-5048	Fluorocarbon (FKM) (75)
-904	1.83	8.92	033-5853	Fluorocarbon (FKM) (90)
-905	1.83	10.52	1J-9671	Nitrile (90)
-905	1.83	10.52	5P-7814	Fluorocarbon (FKM) (75)
	1.88	7.98	6V-5324	Nitrile (90)
	1.90	4.80	095-1572	Nitrile (90)
	1.90	5.80	3T-7528	Nitrile (75)
	1.90	5.80	095-1573	Nitrile (90)
	1.90	7.80	095-1512	Nitrile (75)
	1.90	7.80	095-1575	Nitrile (90)
	1.90	9.80	095-1514	Nitrile (75)
	1.90	9.80	095-1578	Nitrile (90)
	1.90	16.76	6V-6921	Silicone (70)
-906	1.98	11.89	6V-3250	EPDM (70)
-906	1.98	11.89	3J-1907	Nitrile (90)
-906	1.98	11.89	7L-6385	Polyacrylate (75)
-906	1.98	11.89	6V-5049	Fluorocarbon (FKM) (75)
-906	1.98	11.89	033-6042	Fluorocarbon (FKM) (90)
	2.00	7.50	8T-9528	Fluorocarbon (FKM) (90)	DK Green
	2.00	14.00	8T-0116	Nitrile (75)	DK Green
	2.00	17.00	3E-6769	Fluorocarbon (FKM) (90)

Attachment A-6

Table 8

O-RINGS (BY CROSS SECTION)
Dash Size (AS568A)	Section Dia. (mm)	Inside Dia. (mm)	Part Number	Material Name	Color
	2.00	30.00	092-2304	Nitrile (75)
	2.00	80.00	8T-9525	Fluorocarbon (FKM) (75)
	2.00	84.00	107-6279	Nitrile (75)
	2.10	9.40	6V-9028	Nitrile (90)
	2.10	11.40	6V-6560	Nitrile (90)
	2.10	13.40	8T-6850	Nitrile (90)
	2.10	15.40	8T-7524	Nitrile (90)
	2.10	17.40	8T-7877	Nitrile (90)
	2.10	19.40	6N-7970	Nitrile (90)
	2.20	9.60	9X-7317	Fluorocarbon (FKM) (90)	DK Green
-908	2.21	16.36	6V-6609	EPDM (70)
-908	2.21	16.36	9X-7745	Nitrile (75)
-908	2.21	16.36	3K-0360	Nitrile (90)
-908	2.21	16.36	8L-2786	Fluorocarbon (FKM) (75)
-908	2.21	16.36	033-6028	Fluorocarbon (FKM) (90)
	2.38	22.22	2T-2894	Fluorocarbon (FKM) (75)
	2.40	9.30	8T-9521	Fluorocarbon (FKM) (75)
	2.40	10.80	095-1515	Nitrile (75)
	2.40	10.80	095-1579	Nitrile (90)
	2.40	11.80	095-1516	Nitrile (75)
	2.40	11.80	095-1580	Nitrile (90)
	2.40	12.30	095-1581	Nitrile (90)
	2.40	12.30	8T-9522	Fluorocarbon (FKM) (75)
	2.40	13.80	095-1517	Nitrile (75)
	2.40	13.80	095-1582	Nitrile (90)
	2.40	14.80	095-1518	Nitrile (75)
	2.40	14.80	095-1583	Nitrile (90)
	2.40	15.80	095-1519	Nitrile (75)
	2.40	15.80	095-1584	Nitrile (90)
	2.40	16.30	3E-4299	Nitrile (90)
	2.40	17.80	095-1585	Nitrile (90)
	2.40	18.30	8T-9523	Fluorocarbon (FKM) (75)
	2.40	19.08	095-1521	Nitrile (75)
	2.40	20.80	095-1522	Nitrile (75)
	2.40	20.80	095-1587	Nitrile (90)
	2.40	21.80	095-1524	Nitrile (75)
	2.40	21.80	095-1590	Nitrile (90)
	2.40	27.30	9X-4625	Fluorocarbon (FKM) (75)

Attachment A-7

Table 9

O-RINGS (BY CROSS SECTION)
Dash Size (AS568A)	Section Dia. (mm)	Inside Dia. (mm)	Part Number	Material Name	Color
	2.40	27.70	9X-4614	Silicone (70)
	2.40	39.70	8C-0626	Silicone (70)
	2.40	67.60	8T-6716	Nitrile (75)
-910	2.46	19.18	6V-3251	EPDM (70)
-910	2.46	19.18	2M-9780	Nitrile (90)
-910	2.46	19.18	7L-2224	Polyacrylic (75) (ACM)
-910	2.46	19.18	6V-4589	Fluorocarbon (FKM) (75)
-910	2.46	19.18	033-6027	Fluorocarbon (FKM) (90)
	2.48	19.80	095-1586	Nitrile (90)
	2.50	33.00	3E-6764	Nitrile (90)
	2.50	107.00	8C-3083	Fluorocarbon (FKM) (90)	DK Green
	2.50	140.00	8C-3057	Nitrile (75)
	2.50	195.00	3E-6770	Fluorocarbon (FKM) (90)	DK Green
-102	2.62	1.24	7V-5646	Chloroprene Rubber (70)
-106	2.62	4.42	8J-1699	Nitrile (90)
-107	2.62	5.23	8B-7216	Nitrile (75)
-107	2.62	5.23	5P-4933	Nitrile (90)
-108	2.62	6.02	8J-8343	Nitrile (75)
-108	2.62	6.02	5P-5874	Nitrile (90)
-108	2.62	6.02	9X-7676	Fluorocarbon (FKM) (75)
-109	2.62	7.56	4J-2506	Nitrile (75)
-109	2.62	7.56	6J-3134	Nitrile (90)
-109	2.62	7.56	032-8970	Fluorocarbon (FKM) (75)
-110	2.62	9.19	6F-5559	Nitrile (75)
-110	2.62	9.19	4J-5309	Nitrile (90)
-110	2.62	9.19	8M-8157	Silicone (70)
-110	2.62	9.19	6V-4365	Fluorocarbon (FKM) (75)
	2.62	9.80	7W-3983	Nitrile (75)
-111	2.62	10.77	5H-6005	Nitrile (75)
-111	2.62	10.77	4J-9535	Nitrile (90)
-111	2.62	10.77	8M-5127	Silicone (70)
-111	2.62	10.77	8L-2777	Fluorocarbon (FKM) (75)
-112	2.62	12.37	8F-9206	Nitrile (75)
-112	2.62	12.37	7Y-5219	Nitrile (90)
-112	2.62	12.37	8M-5251	Silicone (70)
-112	2.62	12.37	032-9313	Fluorocarbon (FKM) (75)
-113	2.62	13.94	6F-4855	Nitrile (75)
-113	2.62	13.94	4J-5268	Nitrile (90)

Attachment A-8

Table 10

O-RINGS (BY CROSS SECTION)
Dash Size (AS568A)	Section Dia. (mm)	Inside Dia. (mm)	Part Number	Material Name	Color
-113	2.62	13.94	8M-4437	Silicone (70)
-113	2.62	13.94	3P-0647	Fluorocarbon (FKM) (75)
-113	2.62	13.94	6V-8350	Fluorocarbon (FKM) (90)
-114	2.62	15.54	8F-3469	Nitrile (75)
-114	2.62	15.54	5J-2974	Nitrile (90)
-114	2.62	15.54	7L-2180	Polyacrylic (75) (ACM)
-114	2.62	15.54	8M-5260	Silicone (70)
-114	2.62	15.54	061-8639	Fluorocarbon (FKM) (90)
-115	2.62	17.12	6F-6672	Nitrile (75)
-115	2.62	17.12	4J-5351	Nitrile (90)
-115	2.62	17.12	8M-4438	Silicone (70)
-115	2.62	17.12	6J-2245	Fluorocarbon (FKM) (75)
-115	2.62	17.12	6V-8351	Fluorocarbon (FKM) (90)	DK Green
	2.62	17.96	6V-5325	Nitrile (90)
-116	2.62	18.72	7F-8607	Nitrile (75)
-116	2.62	18.72	6V-3922	Nitrile (90)
-116	2.62	18.72	8M-5253	Silicone (70)
-116	2.62	18.72	7L-9061	Fluorocarbon (FKM) (75)
-117	2.62	20.30	4M-8303	Nitrile (75)
-117	2.62	20.30	5P-3108	Nitrile (90)
-117	2.62	20.30	8M-4389	Silicone (70)
-117	2.62	20.30	5P-9186	Fluorocarbon (FKM) (75)
-117	2.62	20.30	033-6041	Fluorocarbon (FKM) (90)
-118	2.62	21.89	9H-6761	Nitrile (75)
-118	2.62	21.89	7J-9933	Nitrile (90)
-118	2.62	21.89	8M-8283	Silicone (70)
-118	2.62	21.89	5P-8356	Fluorocarbon (FKM) (75)
-119	2.62	23.47	4D-9986	Nitrile (75)
-119	2.62	23.47	6V-5326	Nitrile (90)
-119	2.62	23.47	9X-4609	Silicone (70)
-119	2.62	23.47	033-6034	Fluorocarbon (FKM) (75)
-119	2.62	23.47	6V-8352	Fluorocarbon (FKM) (90)
-120	2.62	25.07	3D-4245	Nitrile (75)
-120	2.62	25.07	6V-5556	Nitrile (90)
-120	2.62	25.07	1S-7462	Silicone (70)
-120	2.62	25.07	6V-8958	Urethane (90)	Natural
-120	2.62	25.07	5P-3456	Fluorocarbon (FKM) (75)
-120	2.62	25.07	6V-6339	Fluorocarbon (FKM) (90)

Attachment A-9

Table 11

O-RINGS (BY CROSS SECTION)
Dash Size (AS568A)	Section Dia. (mm)	Inside Dia. (mm)	Part Number	Material Name	Color
-121	2.62	26.64	3D-2992	Nitrile (75)
-121	2.62	26.64	7E-4846	Nitrile (90)	Orange/Red
-121	2.62	26.64	085-7539	Nitrile (90)
-121	2.62	26.64	8M-4431	Silicone (70)
-121	2.62	26.64	6V-6228	Fluorocarbon (FKM) (75)
-122	2.62	28.24	2K-8199	Nitrile (75)
-122	2.62	28.24	099-8232	Nitrile (90)
-122	2.62	28.24	8M-8514	Silicone (70)
-122	2.62	28.24	5P-7530	Fluorocarbon (FKM) (75)
-122	2.62	28.24	6V-4591	Fluorocarbon (FKM) (90)
-123	2.62	29.82	3S-9233	Nitrile (75)
-123	2.62	29.82	6V-8978	Nitrile (90)
-123	2.62	29.82	8M-1112	Silicone (70)
-123	2.62	29.82	7X-4744	Fluorocarbon (FKM) (75)
-124	2.62	31.42	2S-4663	Nitrile (75)
-124	2.62	31.42	8T-5452	Fluorocarbon (FKM) (75)
-124	2.62	31.42	9X-3979	Fluorocarbon (FKM) (75)	Orange
-124	2.62	31.42	9X-7722	Fluorocarbon (FKM) (90)	DK Blue
	2.62	31.72	096-3044	Nitrile (75)
-125	2.62	32.99	2K-8198	Nitrile (90)
-125	2.62	32.99	6V-8218	Nitrile (90)
-125	2.62	32.99	8M-8515	Silicone (70)
-125	2.62	32.99	3E-6747	Fluorocarbon (FKM) (75)
-125	2.62	32.99	6V-3550	Fluorocarbon (FKM) (90)
-125	2.62	32.99	9X-7418	Fluorocarbon (FKM) (90)	DK Blue
-126	2.62	34.59	5M-2057	Nitrile (75)
-126	2.62	34.59	096-6100	Nitrile (90)
-126	2.62	34.59	6V-4367	Fluorocarbon (FKM) (75)
-127	2.62	36.17	6J-2419	Nitrile (75)
-127	2.62	36.17	6V-5393	Nitrile (90)
-127	2.62	36.17	7E-4847	Nitrile (90)	DK Blue
-127	2.62	36.17	5P-8065	Fluorocarbon (FKM) (75)
-127	2.62	36.17	9X-7735	Fluorocarbon (FKM) (90)	DK Green
-128	2.62	37.77	4D-3107	Nitrile (75)
-128	2.62	37.77	6V-5391	Nitrile (90)
-128	2.62	37.77	6F-0249	Silicone (70)
-128	2.62	37.77	8C-0624	Fluorocarbon (FKM) (75)
-128	2.62	37.77	6V-7323	Fluorocarbon (FKM) (90)

Attachment A-10

Table 12

O-RINGS (BY CROSS SECTION)
Dash Size (AS568A)	Section Dia. (mm)	Inside Dia. (mm)	Part Number	Material Name	Color
-129	2.62	39.34	5P-8215	Nitrile (75)
-129	2.62	39.34	7X-8592	Fluorocarbon (FKM) (75)
-129	2.62	39.34	6V-1250	Fluorocarbon (FKM) (90)
-130	2.62	40.94	6V-5597	Nitrile (90)
-131	2.62	42.52	4J-8268	Nitrile (60)
-131	2.62	42.52	4L-7711	Nitrile (75)
-131	2.62	42.52	9X-7432	Fluorocarbon (FKM) (75)
-132	2.62	44.12	2D-0598	Nitrile (75)
-132	2.62	44.12	5P-2568	Nitrile (90)
-132	2.62	44.12	8C-4949	Polyacrylic (75) (ACM)
-132	2.62	44.12	3E-6790	Fluorocarbon (FKM) (75)
-133	2.62	45.69	7D-9749	Nitrile (75)
-133	2.62	45.69	3E-6771	Nitrile (90)
-133	2.62	45.69	8C-3078	Fluorocarbon (FKM) (75)
-134	2.62	47.29	032-9882	Nitrile (75)
-134	2.62	47.29	7D-8048	Chloroprene Rubber (70)
-135	2.62	48.90	3D-2898	Nitrile (75)
-135	2.62	48.90	6V-8676	Fluorocarbon (FKM) (75)
-136	2.62	50.47	8C-3080	Nitrile (75)
-136	2.62	50.47	8C-3079	Fluorocarbon (FKM) (75)
-137	2.62	52.07	005-8593	Nitrile (75)
-138	2.62	53.64	8C-5196	EPDM (70)
-138	2.62	53.64	3D-7805	Nitrile (75)
-138	2.62	53.64	6V-5100	Fluorocarbon (FKM) (75)
-139	2.62	55.25	5J-1808	Nitrile (60)
-139	2.62	55.25	004-1963	Nitrile (75)
-139	2.62	55.25	6V-3832	Fluorocarbon (FKM) (75)
	2.62	56.82	7Y-5269	Nitrile (90)
-141	2.62	58.42	7J-2036	Nitrile (90)
-141	2.62	58.42	3S-4489	Silicone (70)
-141	2.62	58.42	5P-5756	Fluorocarbon (FKM) (75)
-142	2.62	59.99	8T-7000	Nitrile (75)
-142	2.62	59.99	009-2061	Fluorocarbon (FKM) (75)
-143	2.62	61.60	8S-0768	Nitrile (75)
-143	2.62	61.60	6D-7889	Fluorocarbon (FKM) (75)
	2.62	63.17	8C-3081	Nitrile (75)
	2.62	63.17	009-2062	Fluorocarbon (FKM) (75)
	2.62	63.20	8T-2929	EPDM (70)

Attachment A-11

Table 13

O-RINGS (BY CROSS SECTION)
Dash Size (AS568A)	Section Dia. (mm)	Inside Dia. (mm)	Part Number	Material Name	Color
-145	2.40	64.77	5S-4548	Silicone (70)
-145	2.40	64.77	5P-5757	Fluorocarbon (FKM) (75)
-146	2.40	66.34	5M-6509	Nitrile (75)
	2.46	67.94	107-4057	Nitrile (75)
-148	2.46	69.52	004-1964	Nitrile (75)
-149	2.46	71.12	3K-4025	Nitrile (75)
-150	2.46	72.69	5P-0908	Nitrile (75)
-150	2.46	72.69	8C-5197	Fluorocarbon (FKM) (75)
	2.48	75.87	7R-8872	Nitrile (75)
	2.50	75.87	5E-8770	Fluorocarbon (FKM) (75)
	2.50	79.38	107-5769	HNBR (72)
	2.50	79.38	1P-8362	Nitrile (75)
-152	2.50	82.22	5P-3863	Nitrile (75)
-152	2.62	82.22	5P-2569	Nitrile (90)
-152	2.62	82.22	8C-3089	Fluorocarbon (FKM) (75)
-152	2.62	82.22	6V-3551	Fluorocarbon (FKM) (90)
-153	2.62	88.57	8T-6340	EPDM (70)
-153	2.62	88.57	6V-2483	Nitrile (75)
-153	2.62	88.57	6V-3834	Fluorocarbon (FKM) (75)
-154	2.62	94.92	7X-4752	EPDM (70)
-154	2.62	94.92	4F-4097	Nitrile (75)
	2.62	97.80	7X-4804	Fluorocarbon (FKM) (75)
-155	2.62	101.27	3K-0715	Nitrile (75)
-155	2.62	101.27	8T-5049	Fluorocarbon (FKM) (75)
-155	2.62	101.27	6D-7146	Fluorocarbon (FKM) (75)
-156	2.62	107.62	9X-7549	EPDM (70)
-156	2.62	107.62	1T-1068	Fluorocarbon (FKM) (75)
-157	2.62	113.97	6S-3002	Nitrile (90)
-157	2.62	113.97	6V-7350	Fluorocarbon (FKM) (75)
	2.62	120.32	9X-7566	Nitrile (90)
	2.62	120.32	5E-8771	Fluorocarbon (FKM) (75)
-159	2.62	126.67	7J-6285	Nitrile (75)
-159	2.62	126.67	9X-7422	Fluorocarbon (FKM) (75)
-160	2.62	133.02	2P-1692	Nitrile (75)
-161	2.62	139.37	5J-3888	Nitrile (75)
	2.62	145.72	9X-7358	Nitrile (90)
-163	2.62	152.07	5P-3864	Nitrile (75)
-163	2.62	152.07	9X-4576	Fluorocarbon (FKM) (75)

Attachment A-12

Table 14

O-RINGS (BY CROSS SECTION)
Dash Size (AS568A)	Section Dia. (mm)	Inside Dia. (mm)	Part Number	Material Name	Color
-164	2.62	158.42	8T-6404	Nitrile (75)
-164	2.62	158.42	9X-7286	Fluorocarbon (FKM) (75)
	2.62	164.80	4S-7762	EPDM (70)
	2.62	164.80	9X-7391	Nitrile (90)
-166	2.62	171.12	9D-8042	Nitrile (75)
-167	2.62	177.47	5P-5397	Nitrile (75)
	2.62	183.82	9X-7725	Nitrile (75)
-169	2.62	190.17	9X-7683	Nitrile (75)
-169	2.62	190.17	9X-7295	Fluorocarbon (FKM) (75)
-171	2.62	202.87	7X-4799	Silicone (70)
-171	2.62	202.87	9X-7410	Fluorocarbon (FKM) (90)	DK Blue
	2.62	249.50	8C-5175	Nitrile (75)
	2.62	260.00	8C-5177	Nitrile (75)
	2.62	269.40	8C-5176	Nitrile (75)
	2.62	287.91	065-2793	Nitrile (75)
	2.70	13.60	8T-0117	Nitrile (75)
	2.72	19.30	006-2992	Nitrile (75)
	2.80	22.70	8T-7878	Nitrile (90)
	2.80	23.70	8T-7525	Nitrile (90)
	2.80	29.70	8T-7526	Nitrile (90)
	2.80	38.70	8C-5193	Nitrile (90)
-911	2.95	21.92	9X-7692	Nitrile (75)
-912	2.95	23.47	6V-5063	EPDM (70)
-912	2.95	23.47	3D-2824	Nitrile (90)
-912	2.95	23.47	7L-3385	Polyacrylic (75) (ACM)
-912	2.95	23.47	6V-5050	Fluorocarbon (FKM) (75)
-912	2.95	23.47	033-6038	Fluorocarbon (FKM) (90)
-914	2.95	26.59	4K-1388	Nitrile (90)
-914	2.95	26.59	6V-1903	Fluorocarbon (FKM) (75)
-914	2.95	26.59	033-6038	Fluorocarbon (FKM) (90)
-916	2.95	29.74	6V-5064	EPDM (70)
-916	2.95	29.74	9X-7744	Nitrile (75)
-916	2.95	29.74	7M-8485	Nitrile (90)
-916	2.95	29.74	7L-2229	Polyacrylic (75) (ACM)
-916	2.95	29.74	5P-7701	Fluorocarbon (FKM) (75)
-916	2.95	29.74	9X-7712	Fluorocarbon (FKM) (90)
	3.00	36.50	9X-4621	Fluorocarbon (FKM) (75)
-920	3.00	37.47	6V-5065	EPDM (70)

Attachment A-13

Table 15

O-RINGS (BY CROSS SECTION)
Dash Size (AS568A)	Section Dia. (mm)	Inside Dia. (mm)	Part Number	Material Name	Color
-920	3.00	37.47	2S-4078	Nitrile (90)
-920	3.00	37.47	7L-3386	Polyacrylic (75) (ACM)
-920	3.00	37.47	5P-7815	Fluorocarbon (FKM) (75)
	3.00	41.00	2T-2692	Nitrile (70)
-924	3.00	43.69	8C-0562	EPDM (70)
-924	3.00	43.69	6K-6307	Nitrile (90)
-924	3.00	43.69	1N-6002	Polyacrylic (75) (ACM)
-924	3.00	43.69	5P-7816	Fluorocarbon (FKM) (75)
	3.00	51.00	2T-2691	Nitrile (70)
-928	3.00	53.09	8T-2928	EPDM (70)
-928	3.00	53.09	9X-3978	Fluorocarbon (FKM) (75)
-932	3.00	59.36	030-4606	Nitrile (90)
-932	3.00	59.36	5P-7817	Fluorocarbon (FKM) (75)
	3.00	79.50	3C-5546	Nitrile (75)
	3.00	84.50	9X-4622	Fluorocarbon (FKM) (75)
	3.00	105.00	8T-9526	Fluorocarbon (FKM) (75)
	3.00	145.00	4V-2445	EPDM (50)
	3.00	179.50	107-5665	Nitrile (75)
	3.10	186.00	4V-2444	EPDM (50)
	3.10	24.40	095-1657	Nitrile (75)
	3.10	24.40	095-1696	Nitrile (90)
	3.10	29.40	095-1658	Nitrile (75)
	3.10	29.40	095-1698	Nitrile (90)
	3.10	34.90	095-1700	Nitrile (90)
	3.10	39.40	095-1701	Nitrile (90)
	3.10	44.40	095-1703	Nitrile (90)
	3.10	49.40	095-1662	Nitrile (75)
	3.10	49.40	095-1704	Nitrile (90)
	3.10	54.40	095-1663	Nitrile (75)
	3.10	54.40	095-1705	Nitrile (90)
	3.10	59.40	095-1706	Nitrile (90)
	3.10	64.40	095-1707	Nitrile (90)
	3.10	69.40	095-1708	Nitrile (90)
	3.10	74.40	095-1709	Nitrile (90)
	3.10	79.40	095-1710	Nitrile (90)
	3.10	84.40	8T-3338	Nitrile (75)
	3.10	84.40	095-1711	Nitrile (90)
	3.10	89.40	095-1712	Nitrile (90)

Attachment A-14

Table 16

O-RINGS (BY CROSS SECTION)
Dash Size (AS568A)	Section Dia. (mm)	Inside Dia. (mm)	Part Number	Material Name	Color
	3.10	94.40	095-1671	Nitrile (75)
	3.10	94.40	095-1713	Nitrile (90)
	3.10	94.40	096-3944	Fluorocarbon (FKM) (75)
	3.10	99.40	095-1714	Nitrile (90)
	3.10	104.40	095-1673	Nitrile (75)
	3.10	104.40	095-1715	Nitrile (90)
	3.10	109.40	095-1674	Nitrile (75)
	3.10	109.40	095-1716	Nitrile (90)
	3.10	114.40	095-1675	Nitrile (75)
	3.10	114.40	095-1717	Nitrile (90)
	3.10	119.40	095-1676	Nitrile (75)
	3.10	119.40	095-1718	Nitrile (90)
	3.10	124.40	095-1719	Nitrile (90)
	3.10	129.40	095-1678	Nitrile (75)
	3.10	129.40	095-1720	Nitrile (90)
	3.10	134.40	095-1679	Nitrile (75)
	3.10	134.40	095-1721	Nitrile (90)
	3.10	139.40	095-1680	Nitrile (75)
	3.10	139.40	095-1722	Nitrile (90)
	3.10	144.40	095-1681	Nitrile (75)
	3.10	144.40	095-1723	Nitrile (90)
	3.10	160.00	095-7384	Nitrile (90)
	3.10	174.00	095-7383	Nitrile (90)
	3.10	190.00	096-4377	Nitrile (90)
	3.10	259.30	6V-8101	Nitrile (75)
	3.15	30.00	8T-9524	Fluorocarbon (FKM) (75)
	3.18	34.11	4D-5256	Nitrile (75)
	3.18	49.23	4F-2709	Nitrile (75)
	3.18	200.02	3F-8333	Nitrile (75)
	3.18	323.85	4S-5805	Polyacrylic (75) (ACM)
	3.18	377.82	002-6962	Nitrile (90)
	3.18	419.10	4S-5804	Polyacrylic (75) (ACM)
	3.30	31.75	4F-2928	Nitrile (75)
	3.30	66.68	3F-3759	Nitrile (75)
	3.30	74.63	4F-3408	Nitrile (75)
	3.30	106.38	4F-9174	Nitrile (75)
	3.30	195.28	4F-2410	Nitrile (75)
	3.50	21.70	095-1589	Nitrile (90)

Attachment A-15

Table 17

O-RINGS (BY CROSS SECTION)
Dash Size (AS568A)	Section Dia. (mm)	Inside Dia. (mm)	Part Number	Material Name	Color
	3.50	21.70	5I-4115	Urethane (90)	Natural
	3.50	22.10	095-1591	Nitrile (90)
	3.50	23.70	095-1526	Nitrile (75)
	3.50	23.70	095-1592	Nitrile (90)
	3.50	24.70	095-1527	Nitrile (75)
	3.50	24.70	095-1593	Nitrile (90)
	3.50	25.70	095-1528	Nitrile (75)
	3.50	25.70	095-1594	Nitrile (90)
	3.50	27.70	095-1595	Nitrile (90)
	3.50	28.70	095-1530	Nitrile (75)
	3.50	28.70	095-1596	Nitrile (90)
	3.50	29.70	095-1597	Nitrile (90)
	3.50	30.70	095-1532	Nitrile (75)
	3.50	30.70	095-1598	Nitrile (90)
	3.50	31.70	095-1533	Nitrile (75)
	3.50	31.70	095-1599	Nitrile (90)
	3.50	33.70	095-1534	Nitrile (75)
	3.50	33.70	095-1600	Nitrile (90)
	3.50	34.70	095-1601	Nitrile (90)
	3.50	35.70	095-1602	Nitrile (90)
	3.50	37.70	095-1603	Nitrile (90)
	3.50	38.70	095-1538	Nitrile (75)
	3.50	38.70	095-5572	Nitrile (90)
	3.50	39.70	095-1539	Nitrile (75)
	3.50	39.70	095-1604	Nitrile (90)
	3.50	40.70	095-1540	Nitrile (75)
	3.50	40.70	095-1605	Nitrile (90)
	3.50	41.70	095-1541	Nitrile (75)
	3.50	41.70	095-1606	Nitrile (90)
	3.50	43.70	095-1607	Nitrile (90)
	3.50	44.70	095-1543	Nitrile (75)
	3.50	44.70	095-1608	Nitrile (90)
	3.50	45.70	095-1544	Nitrile (75)
	3.50	45.70	095-1609	Nitrile (90)
	3.50	47.70	095-1610	Nitrile (90)
	3.50	48.70	095-1545	Nitrile (75)
	3.50	48.70	095-1611	Nitrile (90)
	3.50	49.70	095-1547	Nitrile (75)

Attachment A-16

Table 18

O-RINGS (BY CROSS SECTION)
Dash Size (AS568A)	Section Dia. (mm)	Inside Dia. (mm)	Part Number	Material Name	Color
	3.50	49.70	095-1613	Nitrile (90)	Natural
	3.50	84.60	8C-5212	Silicone (70)
	3.50	89.60	8C-5213	Silicone (70)
	3.50	94.60	8C-5214	Silicone (70)
-202	3.53	5.94	2H-5001	Nitrile (75)
-202	3.53	5.94	9J-6491	Nitrile (90)
-202	3.53	5.94	8M-8281	Silicone (70)
-202	3.53	5.94	6V-4366	Fluorocarbon (FKM) (75)
-203	3.53	7.52	6V-5555	Nitrile (90)
-204	3.53	9.12	2J-6274	Nitrile (75)
-204	3.53	9.12	6V-0913	Nitrile (90)
-204	3.53	9.12	7X-4805	Fluorocarbon (FKM) (75)
-204	3.53	9.12	6V-3548	Fluorocarbon (FKM) (90)
-205	3.53	10.69	6V-5759	Fluorocarbon (FKM) (75)
-206	3.53	12.29	2M-4453	Nitrile (75)
-206	3.53	12.29	5P-6300	Nitrile (90)
-206	3.53	12.29	8M-4447	Silicone (70)
-206	3.53	12.29	5P-0840	Fluorocarbon (FKM) (75)
	3.53	13.21	5M-1868	Silicone (70)
-207	3.50	13.87	3H-3385	Nitrile (75)
-207	3.53	13.87	8M-8282	Silicone (70)
-208	3.53	15.47	8C-0504	EPDM (70)
-208	3.53	15.47	2J-0157	Nitrile (75)
-208	3.53	15.47	6J-1038	Nitrile (90)
-208	3.53	15.47	8M-4448	Silicone (70)
-208	3.53	15.47	5P-5598	Fluorocarbon (FKM) (75)
-209	3.53	17.04	5P-8119	Fluorocarbon (FKM) (75)
-210	3.53	18.64	5P-3148	EPDM (70)
-210	3.53	18.64	5F-7054	Nitrile (75)
-210	3.53	18.64	4J-5140	Nitrile (90)
-210	3.53	18.64	8M-4435	Silicone (70)
-210	3.53	18.64	5P-6718	Fluorocarbon (FKM) (75)
-211	3.53	20.22	9X-7385	HNBR (72)	Orange
-211	3.53	20.22	1H-8171	Nitrile (75)
-211	3.53	20.22	008-2103	Nitrile (90)
-211	3.53	20.22	061-7539	Fluorocarbon (FKM) (75)
-212	3.53	21.82	3H-0107	Nitrile (75)
-212	3.53	21.82	4J-8996	Nitrile (90)

Attachment A-17

Table 19

O-RINGS (BY CROSS SECTION)
Dash Size (AS568A)	Section Dia. (mm)	Inside Dia. (mm)	Part Number	Material Name	Color
-212	3.50	21.82	8M-4445	Silicone (70)
-212	3.50	21.82	3P-1156	Fluorocarbon (FKM) (75)
-213	3.50	23.39	5H-2767	Nitrile (75)
-213	3.50	23.39	8M-4446	Silicone (70)
-213	3.53	23.39	035-0273	Urethane (90)	Natural
-213	3.53	23.39	6V-3683	Fluorocarbon (FKM) (75)
-214	3.53	24.99	5F-1678	Nitrile (75)
-214	3.53	24.99	4J-5267	Nitrile (90)
-214	3.53	24.99	8M-4988	Silicone (70)
-214	3.53	24.99	3P-1155	Fluorocarbon (FKM) (75)
-215	3.53	26.57	4F-8946	Nitrile (75)
-215	3.53	26.57	7X-1550	Nitrile (90)
-215	3.53	26.57	8M-4432	Silicone (70)
-215	3.53	26.57	5P-8118	Fluorocarbon (FKM) (75)
-216	3.53	28.17	2H-3932	Nitrile (75)
-216	3.53	28.17	4J-8997	Nitrile (90)
-216	3.53	28.17	8M-5248	Silicone (70)
-216	3.53	28.17	061-9458	Fluorocarbon (FKM) (75)
-217	3.53	29.74	4F-9029	Nitrile (75)
-217	3.50	29.74	6V-0357	Nitrile (90)
-217	3.53	29.74	8M-4433	Silicone (70)
-218	3.53	31.34	6F-6673	Nitrile (75)
-218	3.53	31.34	4J-0519	Nitrile (90)
-218	3.53	31.34	8M-5254	Silicone (70)
-218	3.53	31.34	5P-8210	Fluorocarbon (FKM) (75)
-219	3.53	32.92	4F-7391	Nitrile (75)
-219	3.53	32.92	4J-0520	Nitrile (90)
-219	3.53	32.92	8M-4987	Silicone (70)
-219	3.53	32.92	5P-8066	Fluorocarbon (FKM) (75)
-219	3.53	32.92	9X-7557	Fluorocarbon (FKM) (90)	DK Blue
-220	3.53	34.52	7L-4774	EPDM (70)
-220	3.53	34.52	3H-1461	Nitrile (75)
-220	3.53	34.52	4J-0521	Nitrile (90)	DK Blue
-220	3.53	34.52	8M-5249	Silicone (70)
-220	3.53	34.52	5P-4268	Fluorocarbon (FKM) (75)
-221	3.53	36.09	5F-9657	Nitrile (75)
-221	3.53	36.09	4J-8998	Nitrile (90)
-221	3.53	36.09	1S-9799	Silicone (70)

Attachment A-18

Table 20

O-RINGS (BY CROSS SECTION)
Dash Size (AS568A)	Section Dia. (mm)	Inside Dia. (mm)	Part Number	Material Name	Color
-221	3.50	36.09	6V-5266	Fluorocarbon (FKM) (75)
-221	3.50	36.09	9X-7419	Fluorocarbon (FKM) (90)
-222	3.50	37.69	4F-7952	Nitrile (75)
-222	3.50	37.69	4J-0522	Nitrile (90)
-222	3.53	37.69	7L-2175	Polyacrylic (75) (ACM)
-222	3.53	37.69	8M-4986	Silicone (70)
-222	3.53	37.69	061-7540	Fluorocarbon (FKM) (75)
	3.53	37.69	2J-1826	Nitrile (75)
-223	3.53	40.87	6F-0711	Nitrile (75)
-223	3.53	40.87	099-0187	Fluorocarbon (FKM) (75)
-223	3.53	40.87	4J-5573	Nitrile (90)
-223	3.53	40.87	8M-4992	Silicone (70)
-223	3.53	40.87	061-8561	Fluorocarbon (FKM) (75)
-223	3.53	40.87	8J-8725	Fluorocarbon (FKM) (90)
-224	3.53	44.04	8T-9588	EPDM (70)
-224	3.53	44.04	1H-9696	Nitrile (75)
-224	3.53	44.04	4J-0523	Nitrile (90)
-224	3.53	44.04	8M-4443	Silicone (70)
-224	3.53	44.04	8J-4351	Fluorocarbon (FKM) (75)
-224	3.50	44.04	5P-1480	Fluorocarbon (FKM) (90)
-225	3.53	47.22	8T-1702	EPDM (70)
-225	3.53	47.22	7F-8267	Nitrile (75)
-225	3.53	47.22	4J-0524	Nitrile (90)
-225	3.53	47.22	8M-5661	Silicone (70)
-225	3.53	47.22	061-9455	Fluorocarbon (FKM) (75)
-226	3.53	50.39	5F-8000	Nitrile (75)
-226	3.53	50.39	4J-0525	Nitrile (90)
-226	3.53	50.39	8M-4436	Silicone (70)
-226	3.53	50.39	5P-8211	Fluorocarbon (FKM) (75)
-227	3.53	53.57	7F-8268	Nitrile (75)
-227	3.53	53.57	4J-0526	Nitrile (90)
-227	3.53	53.57	8M-5010	Silicone (70)
-227	3.53	53.57	061-9456	Fluorocarbon (FKM) (75)
-227	3.53	53.57	8C-3077	Fluorocarbon (FKM) (90)
-228	3.53	56.74	8T-1703	EPDM (70)
-228	3.53	56.74	8F-6711	Nitrile (75)
-228	3.53	56.74	4J-0527	Nitrile (90)
-228	3.53	56.74	8M-4390	Silicone (70)

Attachment A-19

Table 21

O-RINGS (BY CROSS SECTION)
Dash Size (AS568A)	Section Dia. (mm)	Inside Dia. (mm)	Part Number	Material Name	Color
-228	3.50	56.74	6V-4368	Fluorocarbon (FKM) (75)
-229	3.50	59.92	1H-8720	Nitrile (75)
-229	3.50	59.92	4J-0528	Nitrile (90)
-229	3.50	59.92	1S-2147	Silicone (70)
-229	3.53	59.92	5P-4892	Fluorocarbon (FKM) (75)
-230	3.53	63.09	1H-5728	Nitrile (75)
-230	3.53	63.09	3P-0439	Nitrile (90)
-230	3.53	63.09	8M-4395	Silicone (70)
-230	3.53	63.09	061-9457	Fluorocarbon (FKM) (75)
	3.53	65.07	5B-4399	Nitrile (75)
-231	3.53	66.27	8F-8882	Nitrile (75)
-231	3.53	66.27	3E-6730	Nitrile (90)
-231	3.53	66.27	8M-5252	Silicone (70)
-231	3.53	66.27	6J-2244	Fluorocarbon (FKM) (75)
-232	3.53	69.44	5H-8848	Nitrile (75)
-232	3.53	69.44	6J-2680	Nitrile (90)
-232	3.53	69.44	9M-7539	Silicone (70)
-232	3.53	69.44	033-6031	Fluorocarbon (FKM) (75)
-232	3.53	69.44	8T-0568	Fluorocarbon (FKM) (90)
-233	3.50	72.62	6H-3977	Nitrile (75)
-233	3.53	72.62	6V-1179	Fluorocarbon (FKM) (75)
-234	3.53	75.79	1H-7339	Nitrile (75)
-234	3.53	75.79	5M-3038	Silicone (70)
-234	3.53	75.79	5P-4889	Fluorocarbon (FKM) (75)
-235	3.53	78.97	2H-6184	Nitrile (75)
-235	3.53	78.97	3E-6732	Nitrile (90)
-236	3.53	82.14	8C-3073	EPDM (70)
-236	3.53	82.14	2H-3931	Nitrile (75)
-236	3.53	82.14	6V-6707	Nitrile (90)
-236	3.53	82.14	6L-9965	Silicone (70)
-236	3.53	82.14	6V-1196	Fluorocarbon (FKM) (75)
-237	3.53	85.32	8C-3072	EPDM (70)
-237	3.53	85.32	2H-6338	Nitrile (75)
-237	3.53	85.32	2P-3538	Silicone (70)
-237	3.53	85.32	6V-8001	Fluorocarbon (FKM) (75)
-238	3.53	88.49	2H-4145	Nitrile (75)
-238	3.53	88.49	6R-0365	Nitrile (90)
-238	3.53	88.49	3S-1427	Silicone (70)

Attachment A-20

Table 22

O-RINGS (BY CROSS SECTION)
Dash Size (AS568A)	Section Dia. (mm)	Inside Dia. (mm)	Part Number	Material Name	Color
-238	3.53	88.49	6V-8002	Fluorocarbon (FKM) (75)
-239	3.53	91.67	8H-7521	Nitrile (75)
-239	3.53	91.67	3E-6735	Nitrile (90)
-239	3.53	91.67	2M-2561	Silicone (70)
	3.53	92.08	5D-6618	Nitrile (80)
-240	3.53	94.84	1H-8128	Nitrile (75)
-240	3.53	94.84	5P-6302	Nitrile (90)
-240	3.53	94.84	5K-1770	Silicone (70)
-240	3.53	94.84	3E-6773	Fluorocarbon (FKM) (75)
-241	3.53	98.02	2H-3934	Nitrile (75)
-241	3.53	98.02	9X-4611	Nitrile (90)
-241	3.53	98.02	9M-9936	Silicone (70)
-241	3.53	98.02	6V-1197	Fluorocarbon (FKM) (75)
-242	3.53	101.19	1H-6227	Nitrile (75)
-242	3.53	101.19	2S-2182	Silicone (70)
-242	3.53	101.19	6V-6353	Fluorocarbon (FKM) (75)
-243	3.53	104.37	4M-0189	Nitrile (75)
-243	3.53	104.37	7M-9909	Silicone (70)
-243	3.53	104.37	5D-5957	Fluorocarbon (FKM) (75)
-244	3.50	107.54	2H-3928	Nitrile (75)
-244	3.53	107.54	7L-3313	Polyacrylic (75) (ACM)
-244	3.53	107.54	8S-5654	Silicone (70)
-245	3.53	110.72	4H-9105	Nitrile (75)
-245	3.53	110.72	3E-6703	Nitrile (90)
-245	3.53	110.72	9M-9729	Silicone (70)
-245	3.53	110.72	8T-9527	Fluorocarbon (FKM) (75)
-246	3.53	113.89	5H-6734	Nitrile (75)
-246	3.53	113.89	9X-7287	Fluorocarbon (FKM) (75)
-247	3.53	117.07	2J-8163	Nitrile (75)
-247	3.53	117.07	5D-5958	Fluorocarbon (FKM) (75)
	3.53	117.10	5P-1705	Silicone (70)
-248	3.53	120.24	5F-3144	Nitrile (75)
-248	3.53	120.24	7L-2211	Polyacrylic (75) (ACM)
-248	3.53	120.24	8M-5255	Silicone (70)
-249	3.53	123.42	5F-3999	Nitrile (75)
-249	3.53	123.42	7M-6637	Silicone (70)
-249	3.53	123.42	6V-8260	Fluorocarbon (FKM) (75)
-250	3.53	126.59	5F-3106	Nitrile (75)

Attachment A-21

Table 23

O-RINGS (BY CROSS SECTION)
Dash Size (AS568A)	Section Dia. (mm)	Inside Dia. (mm)	Part Number	Material Name	Color
-250	3.53	126.59	031-4392	Nitrile (90)
-250	3.53	126.59	4S-5898	Silicone (70)
-250	3.53	126.59	9X-7371	Fluorocarbon (FKM) (75)
-251	3.53	129.77	3F-5792	Nitrile (75)
-251	3.53	129.77	7L-4090	Polyacrylic (75) (ACM)
-251	3.53	129.77	5P-3457	Silicone (70)
-251	3.53	129.77	5P-8286	Fluorocarbon (FKM) (75)
-252	3.53	132.94	2H-9247	Nitrile (75)
-252	3.53	132.94	9N-1619	Silicone (70)
-252	3.53	132.94	6V-7351	Fluorocarbon (FKM) (75)
-253	3.53	136.12	2H-3935	Nitrile (75)
-253	3.53	136.12	9N-2693	Silicone (70)
-253	3.53	136.12	6V-1195	Fluorocarbon (FKM) (75)
-254	3.53	139.29	8F-9516	Nitrile (75)
-254	3.53	139.29	8M-5007	Silicone (70)
-255	3.53	142.47	2D-8009	Nitrile (75)
-255	3.53	142.47	6V-1904	Silicone (70)
-256	3.53	145.64	6V-3428	EPDM (70)
-256	3.53	145.64	5H-3252	Nitrile (75)
-256	3.50	145.64	6J-5541	Nitrile (90)
-256	3.53	145.64	6V-3549	Fluorocarbon (FKM) (90)
-257	3.53	148.82	2K-8257	Nitrile (75)
-257	3.53	148.82	3S-5135	Silicone (70)
-258	3.53	151.99	8F-8733	Nitrile (75)
-258	3.53	151.99	7D-9014	Nitrile (90)
-258	3.53	151.99	2L-1778	Polyacrylic (75) (ACM)
-258	3.53	151.99	5D-4311	Silicone (70)
-258	3.53	151.99	6V-5553	Fluorocarbon (FKM) (75)
-259	3.53	158.34	2K-4472	Nitrile (75)
-259	3.53	158.34	7L-3380	Polyacrylic (75) (ACM)
-259	3.53	158.34	8M-4704	Silicone (70)
-259	3.53	158.34	6V-3689	Silicone (70) VMQ	Off White
-259	3.53	158.34	6V-3319	Fluorocarbon (FKM) (75)
-260	3.53	164.69	6F-4718	Nitrile (75)
-260	3.53	164.69	1S-4974	Silicone (70)
-260	3.53	164.69	6V-7681	Fluorocarbon (FKM) (75)
-261	3.53	171.04	9F-1399	Nitrile (75)
-261	3.53	171.04	061-9729	Nitrile (90)

Attachment A-22

Table 24

O-RINGS (BY CROSS SECTION)
Dash Size (AS568A)	Section Dia. (mm)	Inside Dia. (mm)	Part Number	Material Name	Color
-261	3.53	171.04	2S-4071	Silicone (70)
-261	3.53	171.04	5P-8428	Fluorocarbon (FKM) (75)
-262	3.53	177.39	2K-2939	Nitrile (75)
-262	3.53	177.39	7L-2181	Polyacrylic (75) (ACM)
-262	3.53	177.39	5S-4554	Silicone (70)
-262	3.53	177.39	6V-1902	Fluorocarbon (FKM) (75)
-263	3.53	183.74	4H-6520	Nitrile (75)
-263	3.53	183.74	1S-6119	Silicone (70)
-263	3.53	183.74	6V-3907	Fluorocarbon (FKM) (75)
-264	3.53	190.09	6V-5098	EPDM (70)
-264	3.53	190.09	3J-0634	Nitrile (75)
-264	3.53	190.09	5J-2383	Nitrile (90)
-265	3.53	196.44	1H-8278	Nitrile (75)
-265	3.53	196.44	8L-5189	Polyacrylic (75) (ACM)
-266	3.53	202.79	1J-2176	Nitrile (75)
-266	3.53	202.79	7Y-4277	Nitrile (90)
-266	3.53	202.79	9M-9545	Silicone (70)
	3.53	204.00	9C-3493	Nitrile (90)
-267	3.53	209.14	9M-5024	Nitrile (75)
-267	3.50	209.14	7Y-4294	Nitrile (90)
-267	3.53	209.14	9N-2694	Silicone (70)
	3.53	214.30	2M-0340	Nitrile (75)
-268	3.53	215.49	4K-6804	Nitrile (75)
-269	3.53	221.84	8F-5900	Nitrile (75)
-270	3.53	228.19	8F-6230	Nitrile (75)
-270	3.53	228.19	6V-3684	Fluorocarbon (FKM) (75)
-271	3.53	234.54	1T-0132	Nitrile (75)
-271	3.53	234.54	8L-3017	Silicone (70)
-272	3.53	240.89	2D-9572	Nitrile (75)
-272	3.53	240.89	9N-1609	Silicone (70)
-273	3.53	247.24	5S-3676	Nitrile (75)
-274	3.53	253.59	5H-4909	Nitrile (75)
-274	3.53	253.59	7D-1979	Silicone (70)
-275	3.53	266.29	8J-8879	Nitrile (75)
	3.53	269.88	9H-5548	Nitrile (75)
-276	3.53	278.99	2R-0239	Nitrile (75)
	3.53	281.94	5D-4187	Nitrile (90)
	3.53	282.37	6V-7991	Nitrile (75)

Attachment A-23

Table 25

O-RINGS (BY CROSS SECTION)
Dash Size (AS568A)	Section Dia. (mm)	Inside Dia. (mm)	Part Number	Material Name	Color
	3.53	185.80	4D-5497	Nitrile (90)
-277	3.53	291.69	5P-2545	Nitrile (75)
-277	3.53	291.69	9N-1520	Silicone (70)
	3.53	298.45	9X-7686	Nitrile (75)
-278	3.53	304.39	2D-6533	Nitrile (75)
	3.53	307.57	5P-9035	Fluorocarbon (FKM) (75)
	3.53	316.87	5P-2861	Nitrile (75)
	3.53	317.91	6V-2406	Silicone (70)
	3.53	323.44	5J-1086	Nitrile (90)
-279	3.53	329.79	4D-6695	Nitrile (75)
-279	3.53	329.79	9N-1552	Silicone (70)
-280	3.53	355.19	4S-5879	Nitrile (75)
-280	3.53	355.19	9N-1562	Silicone (70)
-280	3.53	355.19	5D-5959	Fluorocarbon (FKM) (75)
	3.53	367.89	6D-0692	Nitrile (75)
-281	3.53	380.59	4D-1577	Nitrile (75)
	3.53	385.34	8D-2714	Nitrile (75)
	3.53	385.34	6V-5058	Fluorocarbon (FKM) (75)
	3.53	399.80	5P-9147	Nitrile (75)
-282	3.50	405.26	7S-8561	Nitrile (75)
	3.53	412.34	2P-3628	Nitrile (75)
-283	3.53	430.66	4S-5924	Nitrile (75)
	3.53	454.91	7X-1548	Nitrile (75)
	3.53	470.00	8C-5240	Nitrile (75)
	3.53	481.46	2S-6507	Nitrile (75)
	3.53	523.47	7D-7519	Nitrile (75)
	3.53	535.50	6V-6204	Nitrile (75)
	3.53	552.04	4D-0449	Nitrile (75)
	3.53	570.00	9X-7550	Silicone (70)
	3.53	576.48	7Y-0640	Nitrile (75)
	3.53	606.02	7D-5868	Nitrile (75)
	3.53	622.35	7D-5863	Nitrile (80)
	3.53	631.82	7D-7228	Nitrile (80)
	3.53	698.09	6D-1355	Nitrile (75)
	3.53	749.00	5P-4076	Nitrile (75)
	3.96	11.13	4F-5675	Nitrile (75)
	3.96	11.13	1H-3748	Silicone (70)
	3.96	14.27	3H-2387	Silicone (70)

Attachment A-24

Table 26

O-RINGS (BY CROSS SECTION)
Dash Size (AS568A)	Section Dia. (mm)	Inside Dia. (mm)	Part Number	Material Name	Color
	3.96	22.22	4F-5676	Nitrile (75)
	3.96	25.40	8B-6015	Nitrile (70)
	3.96	38.10	3H-2389	Silicone (70)
	3.96	76.20	4D-6773	Silicone (70)
	3.96	87.53	7H-0538	Silicone (70)
	3.96	117.48	7F-6268	Nitrile (75)
	4.00	95.00	3E-6752	Silicone (70)
	4.00	140.00	9X-7440	Nitrile (75)
	4.00	172.00	8C-3058	Nitrile (75)
	4.29	9.52	7B-0305	Nitrile (75)
	4.30	9.53	3S-5496	Silicone (70)
	4.30	77.50	6P-8160	ECO (60)
	4.30	95.50	9P-9661	ECO (60)
	4.31	140.20	1Y-3606	EPDM (70)
	4.31	140.20	3E-6777	Fluorocarbon (FKM) (75)	DK Blue
	4.39	42.88	7B-6868	Nitrile (75)
	4.39	101.60	7B-2125	Nitrile (75)
	4.39	113.80	3S-3977	EPDM (70)
	4.39	117.10	5S-6670	EPDM (70)
	4.78	7.92	2A-3307	Nitrile (75)
	4.78	20.62	5B-3718	Chloroprene Rubber (50)
	4.78	25.40	2A-3854	Nitrile (75)
	4.78	73.02	3F-9141	Nitrile (75)
	4.78	76.20	5B-3323	Nitrile (75)
	4.78	83.95	3H-2726	Silicone (70)
	4.78	93.68	5B-4484	Nitrile (75)
	4.78	107.92	1Y-6637	Nitrile (75)
	4.78	193.68	7F-7151	Nitrile (75)
	4.78	219.08	7B-5716	Nitrile (75)
	4.78	249.22	9F-3384	Nitrile (75)
	4.78	290.53	7F-2094	Nitrile (75)
	4.78	320.68	7F-2093	Nitrile (75)
	4.78	469.90	4F-2411	Nitrile (75)
	4.88	84.07	6F-8509	Nitrile (75)
	4.88	112.73	4F-7471	Nitrile (75)
	4.88	133.80	6H-6998	EPDM (70)
	4.88	139.803	3S-3978	EPDM (70)
	4.88	152.40	6L-7812	EPDM (70)

Attachment A-25

Table 27

O-RINGS (BY CROSS SECTION)
Dash Size (AS568A)	Section Dia. (mm)	Inside Dia. (mm)	Part Number	Material Name	Color
	4.88	165.10	6L-7815	EPDM (70)
	4.88	175.00	7N-2046	EPDM (70)
	5.00	205.00	8C-3059	Nitrile (75)
	5.33	7.14	3H-2388	Silicone (70)
-310	5.33	12.07	3H-4970	Nitrile (75)
-310	5.33	12.07	1S-7104	Silicone (70)
-310	5.33	12.07	8S-5011	Fluorocarbon (FKM) (75)
-310	5.33	15.24	5H-8038	Nitrile (75)
-312	5.33	15.24	8M-4990	Silicone (70)
-312	5.33	15.24	6V-3955	Fluorocarbon (FKM) (75)
-314	5.33	18.42	6V-5061	EPDM (70)
-314	5.33	18.42	3B-8453	Nitrile (75)
-314	5.33	18.42	1S-0004	Silicone (70)
-314	5.33	18.42	6V-3348	Fluorocarbon (FKM) (75)
	5.33	19.30	9M-4618	Silicone (70)
	5.33	19.99	9H-4557	Nitrile (75)
-316	5.33	21.59	6V-5062	EPDM (70)
-316	5.33	21.59	6H-5672	Nitrile (75)
-316	5.33	21.59	9H-6067	Silicone (70)
-316	5.33	21.59	2N-3350	Fluorocarbon (FKM) (75)
-317	5.33	23.16	7L-4773	EPDM (70)
-317	5.33	23.16	8F-4994	Nitrile (75)
-317	5.33	23.16	9M-4849	Silicone (70)
-317	5.33	23.16	5P-9890	Fluorocarbon (FKM) (75)
-317	5.33	23.16	032-8969	Fluorocarbon (FKM) (90)
-318	5.33	24.77	8T-0280	EPDM (70)
-318	5.33	24.77	8B-4967	Nitrile (75)
-318	5.33	24.77	8M-5266	Silicone (70)
-318	5.33	24.77	6V-4480	Fluorocarbon (FKM) (75)
-320	5.33	27.94	5H-7370	Nitrile (75)
-320	5.33	27.94	8M-4991	Silicone (70)
-320	5.33	27.94	3P-0648	Fluorocarbon (FKM) (75)
-322	5.33	31.12	7L-6580	EPDM (70)
-322	5.33	31.12	4F-5607	Nitrile (75)
-322	5.33	31.12	5H-7153	Silicone (70)
-322	5.33	31.12	6V-5134	Fluorocarbon (FKM) (75)
-323	5.33	32.69	5M-7423	Nitrile (75)
-324	5.33	32.69	5P-7204	EPDM (70)

Attachment A-26

Table 28

O-RINGS (BY CROSS SECTION)
Dash Size (AS568A)	Section Dia. (mm)	Inside Dia. (mm)	Part Number	Material Name	Color
-324	5.33	34.29	5M-5860	Nitrile (75)
-324	5.33	34.29	5P-5316	Polyacrylic (75) (ACM)
-324	5.33	34.29	1A-9544	Silicone (70)
-324	5.33	34.29	6V-3830	Fluorocarbon (FKM) (75)
-325	5.33	37.47	6V-9769	EPDM (70)
-325	5.33	37.47	3S-6538	Nitrile (60)
-325	5.33	37.47	4F-7389	Nitrile (75)
-325	5.33	37.47	5L-2727	Polyacrylic (75) (ACM)
-325	5.33	37.47	9M-7002	Silicone (70)
-325	5.33	37.47	5P-8068	Fluorocarbon (FKM) (75)
-326	5.33	40.64	6L-7817	EPDM (70)
-326	5.33	40.64	2H-3927	Nitrile (75)
-326	5.33	40.64	8S-5953	Nitrile (90)
-326	5.33	40.64	9M-9647	Silicone (70)
-326	5.33	40.64	5P-5846	Fluorocarbon (FKM) (75)
-327	5.33	43.82	2N-5749	EPDM (70)
-327	5.33	43.82	4F-8824	Nitrile (75)
-327	5.33	43.82	2S-2251	Silicone (70)
-327	5.33	43.82	8C-5230	Fluorocarbon (FKM) (75)
	5.33	46.20	9M-2610	Silicone (70)
-328	5.33	46.99	6V-1585	EPDM (70)
-328	5.33	46.99	4F-9653	Nitrile (75)
-328	5.33	46.99	9S-8307	Nitrile (90)
-328	5.33	46.99	6L-1648	Silicone (70)
-328	5.33	46.99	7S-3206	Silicone (70) VMQ	Off White
-328	5.33	46.99	8C-3107	Fluorocarbon (FKM) (75)
-328	5.33	46.99	6V-2859	XNBR
-329	5.33	50.17	5S-1105	EPDM (70)
-329	5.33	50.17	2H-3088	Nitrile (60)
-329	5.33	50.17	5K-5959	Nitrile (75)
-329	5.33	50.17	6L-1651	Silicone (70)
-329	5.33	50.17	3P-0650	Fluorocarbon (FKM) (75)
-330	5.33	53.34	2N-5243	EPDM (70)
-330	5.33	53.34	4F-7390	Nitrile (75)
-330	5.33	53.34	6V-3831	Fluorocarbon (FKM) (75)
-331	5.33	56.52	2N-0475	EPDM (70)
-331	5.33	56.52	3H-2652	Nitrile (75)
-331	5.33	56.52	7S-4001	Nitrile (90)

Attachment A-27

Table 29

O-RINGS (BY CROSS SECTION)
Dash Size (AS568A)	Section Dia. (mm)	Inside Dia. (mm)	Part Number	Material Name	Color
-331	5.33	56.52	6L-1650	Silicone (70)
-331	5.33	56.52	3P-0649	Fluorocarbon (FKM) (75)
-332	5.33	59.69	6F-8146	Nitrile (75)
-332	5.33	59.69	6L-9284	Silicone (70)
-332	5.33	59.69	3P-0651	Fluorocarbon (FKM) (75)
-333	5.33	62.87	8T-1919	EPDM (70)
-333	5.33	62.87	2H-2665	Nitrile (75)
-333	5.33	62.87	2R-0039	Nitrile (90)
-333	5.33	62.87	6L-1649	Silicone (70)
-333	5.33	62.87	3P-0657	Fluorocarbon (FKM) (75)
-334	5.33	66.04	2H-3933	Nitrile (75)
-334	5.33	66.04	8H-1607	Silicone (70)
-334	5.33	66.04	3P-0656	Fluorocarbon (FKM) (75)
-335	5.33	69.22	7F-2122	Nitrile (75)
-335	5.33	69.22	006-8352	Nitrile (90)
-335	5.33	69.22	8M-4989	Silicone (70)
-335	5.33	69.22	3P-0653	Fluorocarbon (FKM) (75)
-336	5.33	72.39	6V-1454	EPDM (70)
-336	5.33	72.39	5F-3092	Nitrile (75)
-336	5.33	72.39	9M-4218	Silicone (70)
-336	5.33	72.39	3P-0655	Fluorocarbon (FKM) (75)
-337	5.33	75.57	7H-2444	Nitrile (75)
-337	5.33	75.57	6V-5051	Fluorocarbon (FKM) (75)
-338	5.33	78.74	9F-4446	Nitrile (75)
-338	5.33	78.74	7L-2174	Polyacrylic (75) (ACM)
-338	5.33	78.74	1M-6036	Silicone (70)
-338	5.33	78.74	6V-3833	Fluorocarbon (FKM) (75)
-339	5.33	81.92	4L-9564	Nitrile (75)
-339	5.33	81.92	5D-1597	Nitrile (90)
-339	5.33	81.92	6L-5359	Silicone (70)
-339	5.33	81.92	6V-5656	Fluorocarbon (FKM) (75)
-340	5.33	85.09	6V-5066	EPDM (70)
-340	5.33	85.09	8H-2046	Nitrile (75)
-340	5.33	85.09	9M-4217	Silicone (70)
-340	5.33	85.09	3P-0654	Fluorocarbon (FKM) (75)
-341	5.33	88.27	1H-0474	Nitrile (75)
-341	5.33	88.27	6V-0973	Fluorocarbon (FKM) (75)
-342	5.33	91.44	5F-0149	Nitrile (75)

Attachment A-28

Table 30

O-RINGS (BY CROSS SECTION)
Dash Size (AS568A)	Section Dia. (mm)	Inside Dia. (mm)	Part Number	Material Name	Color
-342	5.33	91.44	9X-7727	Silicone (70)
-342	5.33	91.44	5P-7818	Fluorocarbon (FKM) (75)
-343	5.33	94.62	5H-8624	Nitrile (75)
-343	5.33	94.62	6V-4315	Fluorocarbon (FKM) (75)
-344	5.33	97.79	6V-5139	EPDM (70)
-344	5.33	97.79	9M-2092	Nitrile (75)
-344	5.33	97.79	6V-5188	Silicone (70)
-344	5.33	97.79	5S-9134	Fluorocarbon (FKM) (75)
-345	5.33	100.97	4F-7387	Nitrile (75)
-345	5.33	100.97	9X-7458	Nitrile (90)
-345	5.33	100.97	7L-2197	Polyacrylic (75) (ACM)
-345	5.33	100.97	4H-3243	Silicone (70)
-345	5.33	100.97	6V-3908	Fluorocarbon (FKM) (75)
-346	5.33	104.14	1J-2859	Nitrile (75)
-346	5.33	104.14	6V-5052	Fluorocarbon (FKM) (75)
-347	5.33	107.32	6V-5504	EPDM (70)
-347	5.33	107.32	9F-7283	Nitrile (75)
-347	5.33	107.32	1S-1225	Silicone (70)
-347	5.33	107.32	6V-5101	Fluorocarbon (FKM) (75)
-348	5.33	110.49	1S-7408	Nitrile (75)
-348	5.33	110.49	7D-7111	Fluorocarbon (FKM) (75)
-349	5.33	113.67	6V-5140	EPDM (70)
-349	5.33	113.67	5H-5672	Nitrile (75)
-349	5.33	113.67	8S-5655	Silicone (70)
-349	5.33	113.67	5P-8872	Fluorocarbon (FKM) (75)
-350	5.33	116.84	6V-5067	EPDM (70)
-350	5.33	116.84	5P-4326	Nitrile (75)
-350	5.33	116.84	8C-3103	Fluorocarbon (FKM) (75)
-351	5.33	120.02	1P-9005	Nitrile (75)
-351	5.33	120.02	5P-8940	Fluorocarbon (FKM) (75)
-352	5.33	123.19	8T-2903	EPDM (70)
-352	5.33	123.19	2S-8439	Nitrile (75)
-352	5.33	123.19	7X-1547	Fluorocarbon (FKM) (75)
-353	5.33	126.37	068-9002	Nitrile (75)
-354	5.33	129.54	6V-5068	EPDM (70)
-354	5.33	129.54	8J-1688	Nitrile (75)
-354	5.33	129.54	6V-4314	Fluorocarbon (FKM) (75)
-355	5.33	132.72	5P-1979	Nitrile (75)

Attachment A-29

Table 31

O-RINGS (BY CROSS SECTION)
Dash Size (AS568A)	Section Dia. (mm)	Inside Dia. (mm)	Part Number	Material Name	Color
	5.33	135.89	9X-7562	Fluorocarbon (FKM) (75)
-357	5.33	139.07	6V-6809	EPDM (70)
-357	5.33	139.07	9M-3786	Nitrile (75)
-357	5.33	139.07	3S-1219	Silicone (70)
-357	5.33	139.07	6V-5054	Fluorocarbon (FKM) (75)
-358	5.33	142.24	6D-9157	Nitrile (75)
-358	5.33	142.24	6V-3835	Fluorocarbon (FKM) (75)
-359	5.33	145.42	3S-1223	Nitrile (75)
-360	5.33	148.59	6V-5657	Nitrile (75)
-361	5.33	151.77	7J-8956	Nitrile (75)
-361	5.33	151.77	6V-5055	Fluorocarbon (FKM) (75)
-362	5.33	158.12	8T-6444	Nitrile (75)
-362	5.33	158.12	8C-3091	Silicone (70)
-362	5.33	158.12	6V-4297	Fluorocarbon (FKM) (75)
-363	5.33	164.47	8J-1665	Nitrile (75)
-363	5.33	164.47	7S-8758	Silicone (70)
-364	5.33	170.82	5P-7593	Nitrile (90)
-365	5.33	177.17	107-6280	HNBR (72)
-365	5.33	177.17	8T-7568	Nitrile (75)
-366	5.33	183.52	5K-1787	Nitrile (75)
-366	5.33	183.52	6V-5102	Fluorocarbon (FKM) (75)
-367	5.33	189.87	3F-1547	Nitrile (75)
-368	5.33	196.22	5M-7142	Nitrile (75)
-368	5.33	196.22	6V-3349	Fluorocarbon (FKM) (75)
	5.33	199.39	8J-4386	Nitrile (90)
-369	5.33	202.57	6V-7703	EPDM (70)
-369	5.33	202.57	9M-5894	Nitrile (75)
-370	5.33	208.92	4N-1230	Nitrile (75)
-370	5.33	208.92	5P-8429	Fluorocarbon (FKM) (75)
-371	5.33	215.27	5P-3092	Nitrile (75)
-372	5.33	221.62	5H-4081	Nitrile (75)
-372	5.33	221.62	1U-3174	Nitrile (90)
-372	5.33	221.62	6V-5141	Fluorocarbon (FKM) (75)
-373	5.33	227.97	5P-5374	Nitrile (90)
-373	5.33	227.97	5D-9344	Silicone (70)
-374	5.33	234.32	6V-5375	Fluorocarbon (FKM) (75)
-375	5.33	240.67	5P-2235	Nitrile (90)
-375	5.33	240.67	5P-8105	Silicone (70)

Attachment A-30

Table 32

O-RINGS (BY CROSS SECTION)
Dash Size (AS568A)	Section Dia. (mm)	Inside Dia. (mm)	Part Number	Material Name	Color
-375	5.33	240.67	6V-7701	Fluorocarbon (FKM) (75)
-377	5.33	253.36	8L-9241	Nitrile (75)
-378	5.33	266.07	3S-3074	Nitrile (75)
-378	5.33	266.07	5P-5819	Silicone (70)
-379	5.33	278.77	5P-2236	Nitrile (90)
-379	5.33	278.77	6V-5554	Fluorocarbon (FKM) (75)
	5.33	287.00	8C-9023	Fluorocarbon (FKM) (75)
-380	5.33	291.47	2M-1309	Nitrile (75)
-380	5.33	291.47	6V-5057	Fluorocarbon (FKM) (75)
-381	5.33	304.17	6V-3263	Nitrile (90)
	5.33	310.13	5H-4082	Nitrile (75)
	5.33	317.24	6V-7702	Fluorocarbon (FKM) (75)
	5.33	325.00	1W-0115	EPDM (70)
-382	5.33	329.57	7S-8554	Nitrile (75)
-382	5.33	329.57	9X-7688	Fluorocarbon (FKM) (75)
	5.33	335.00	6V-3602	Fluorocarbon (FKM) (75)
	5.33	342.90	2M-3818	Nitrile (75)
-383	5.33	354.97	6V-1175	Nitrile (75)
-383	5.33	354.97	8C-3828	Fluorocarbon (FKM) (75)
	5.33	372.00	8T-0098	Fluorocarbon (FKM) (75)
-384	5.33	380.37	2M-3340	Nitrile (75)
	5.33	383.60	9X-7428	Fluorocarbon (FKM) (75)
	5.33	399.42	7S-4571	Nitrile (75)
-385	5.33	405.30	5M-6200	Nitrile (75)
	5.33	411.489	5M-7329	Nitrile (75)
	5.33	415.00	6V-9670	Fluorocarbon (FKM) (75)
	5.33	421.70	8T-8883	Fluorocarbon (FKM) (75)
-386	5.33	430.66	5P-9806	Nitrile (75)
-386	5.33	430.66	9L-5650	Silicone (70)
	5.33	440.69	6M-5218	Nitrile (75)
-387	5.33	456.06	2R-0098	Nitrile (75)
-387	5.33	456.06	6V-5059	Fluorocarbon (FKM) (75)
-388	5.33	481.41	8D-4771	Nitrile (75)
	5.33	494.66	9H-0846	Nitrile (75)
	5.33	494.66	6V-5043	Fluorocarbon (FKM) (75)
	5.33	514.65	9M-5892	Nitrile (75)
-390	5.33	532.21	4H-6730	Nitrile (75)
	5.33	548.64	8S-6251	Silicone (70)

Attachment A-31

Table 33

O-RINGS (BY CROSS SECTION)
Dash Size (AS568A)	Section Dia. (mm)	Inside Dia. (mm)	Part Number	Material Name	Color
-391	5.33	557.61	9H-3360	Nitrile (75)
-392	5.33	582.68	3D-8422	Nitrile (75)
-393	5.33	608.10	8T-3013	Nitrile (75)
-394	5.33	633.38	9H-6832	Nitrile (75)
	5.33	643.38	8D-5096	Nitrile (75)
	5.33	684.28	5D-7523	Nitrile (75)
	5.33	736.60	2D-6506	Nitrile (75)
	5.33	760.00	5P-4057	Nitrile (75)
	5.33	786.76	3D-3295	Nitrile (75)
	5.33	843.00	5P-9519	Nitrile (75)
	5.33	940.00	6V-6557	Silicone (70)
	5.70	45.60	8C-0627	Silicone (70)
	5.70	49.60	095-1546	Nitrile (75)
	5.70	49.60	095-1612	Nitrile (90)
	5.70	54.60	8T-6346	Nitrile (75)
	5.70	59.60	095-1549	Nitrile (75)
	5.70	59.60	095-1619	Nitrile (90)
	5.70	61.60	095-1620	Nitrile (90)
	5.70	69.60	095-1551	Nitrile (75)
	5.70	69.60	095-1622	Nitrile (90)
	5.70	74.60	095-1552	Nitrile (75)
	5.70	79.60	095-1553	Nitrile (75)
	5.70	79.60	095-1623	Nitrile (90)
	5.70	89.60	095-1555	Nitrile (75)
	5.70	89.60	095-1625	Nitrile (90)
	5.70	94.60	095-1626	Nitrile (90)
	5.70	99.60	095-1557	Nitrile (75)
	5.70	99.60	095-1627	Nitrile (90)
	5.70	109.60	095-1558	Nitrile (75)
	5.70	109.60	095-1628	Nitrile (90)
	5.70	114.60	095-1560	Nitrile (75)
	5.70	119.60	095-1631	Nitrile (90)
	5.70	129.60	095-1632	Nitrile (90)
	5.70	139.60	095-1563	Nitrile (75)
	5.70	139.60	095-1633	Nitrile (90)
	5.70	144.60	095-1564	Nitrile (75)
	5.70	144.60	095-1634	Nitrile (90)
	5.70	149.30	095-1724	Nitrile (90)

Attachment A-32

Table 34

O-RINGS (BY CROSS SECTION)
Dash Size (AS568A)	Section Dia. (mm)	Inside Dia. (mm)	Part Number	Material Name	Color
	5.70	149.60	095-1635	Nitrile (90)
	5.70	154.30	096-4921	Nitrile (75)
	5.70	154.30	095-1725	Nitrile (90)
	5.70	159.30	095-1726	Nitrile (90)
	5.70	164.30	095-1727	Nitrile (90)
	5.70	169.30	095-1684	Nitrile (75)
	5.70	169.30	095-1728	Nitrile (90)
	5.70	174.30	095-1729	Nitrile (90)
	5.70	179.30	095-1685	Nitrile (75)
	5.70	179.30	095-1730	Nitrile (90)
	5.70	189.30	095-1687	Nitrile (75)
	5.70	189.30	095-1731	Nitrile (90)
	5.70	209.30	095-1690	Nitrile (75)
	5.70	209.30	095-1733	Nitrile (90)
	5.70	229.30	095-1692	Nitrile (75)
	5.70	229.30	095-1735	Nitrile (90)
	5.70	249.30	095-1693	Nitrile (75)
	5.70	249.30	095-1736	Nitrile (90)
	5.70	259.30	095-1737	Nitrile (90)
	5.70	279.30	095-1694	Nitrile (75)
	5.70	279.30	095-1738	Nitrile (90)
	5.70	289.30	9X-4623	Fluorocarbon (FKM) (75)
	5.70	299.30	095-1695	Nitrile (75)
	5.84	59.69	6V-2699	Nitrile (75)
	5.84	72.39	6V-2701	Nitrile (75)
	5.84	72.39	8T-2272	Silicone (70)
	5.84	81.40	6V-2700	Nitrile (75)
	5.84	87.80	6V-2698	Nitrile (75)
	5.84	113.66	6V-2475	Nitrile (75)
	6.22	49.23	2B-8293	Nitrile (75)
	6.22	92.72	6S-3284	Nitrile (60) (Toric Ring)
	6.22	92.72	3N-3095	Silicone (70) (Toric Ring)
	6.22	128.23	3S-0302	Nitrile (60) (Toric Ring)
	6.22	128.23	8L-5520	Silicone (70) (Toric Ring)
	6.22	143.52	5K-5129	Nitrile (60) (Toric Ring)
	6.22	143.52	3N-3097	Silicone (70) (Toric Ring)
	6.22	154.50	5K-1075	Nitrile (60) (Toric Ring)
	6.22	154.50	8L-5517	Silicone (70) (Toric Ring)

Attachment A-33

Table 35

O-RINGS (BY CROSS SECTION)
Dash Size (AS568A)	Section Dia. (mm)	Inside Dia. (mm)	Part Number	Material Name	Color
	6.22	207.15	5N-7644	Nitrile (55) (Toric Ring)
	6.35	28.58	6F-6600	Nitrile (75)
	6.35	40.49	1A-2298	Nitrile (75)
	6.35	53.98	6L-7816	EPDM (70)
	6.35	53.98	6B-7021	Nitrile (60)
	6.35	60.96	7F-9134	Nitrile (75)
	6.99	139.70	7B-2123	Nitrile (75)
	6.99	12.70	3B-7363	Nitrile (75)
	6.99	31.12	8C-5209	EPDM (70)
	6.99	31.12	4H-1860	Nitrile (75)
	6.99	31.12	6L-4905	Silicone (70)
	6.99	37.46	7H-9959	Nitrile (75)
	6.99	42.80	8S-0530	Nitrile (75)
	6.99	46.99	1M-3548	Nitrile (75)
	6.99	56.52	7D-1195	Nitrile (75)
	6.99	56.52	4M-0142	Silicone (70)
	6.99	56.52	5P-6861	Fluorocarbon (FKM) (75)
	6.99	61.60	5P-8432	Nitrile (75)
	6.99	64.26	1T-0136	Nitrile (75)
	6.99	69.22	1M-0556	Nitrile (75)
	6.99	69.22	4M-0141	Silicone (70)
	6.99	75.56	5H-2824	Fluorocarbon (FKM) (75)
	6.99	75.56	5H-9205	Silicone (70)
	6.99	81.00	4L-8337	Silicone (70)
	6.99	81.92	7L-7459	EPDM (70)
	6.99	81.92	5P-5700	Fluorocarbon (FKM) (75)
	6.99	85.09	2A-3676	Nitrile (75)
	6.99	88.26	6K-9149	Nitrile (75)
	6.99	88.26	5S-1188	Silicone (70)
	6.99	91.44	5S-0982	Nitrile (75)
	6.99	94.61	5H-7704	Silicone (70)
	6.99	94.62	7L-7460	EPDM (70)
	6.99	94.62	6V-3917	Fluorocarbon (FKM) (75)
	6.99	100.96	5H-1039	Silicone (70)
	6.99	100.96	6V-2695	Fluorocarbon (FKM) (75)
	6.99	104.14	8H-7469	Silicone (70)
	6.99	107.31	6H-1871	Silicone (70)
	6.99	107.31	6V-5166	Fluorocarbon (FKM) (75)

Attachment A-34

Table 36

O-RINGS (BY CROSS SECTION)
Dash Size (AS568A)	Section Dia. (mm)	Inside Dia. (mm)	Part Number	Material Name	Color
-425	6.99	113.67	7S-1156	Silicone (70)
-426	6.99	116.84	9S-3888	Nitrile (75)
-426	6.99	116.84	9M-8788	Silicone (70)
-427	6.99	120.02	7L-2031	EPDM (70)
-427	6.99	120.02	3H-0976	Silicone (70)
-428	6.99	123.19	6F-0671	Nitrile (90)
-428	6.99	123.19	5S-6760	Fluorocarbon (FKM) (75)
-429	6.99	126.37	6L-9405	EPDM (70)
-429	6.99	126.37	8F-4469	Nitrile (75)
-429	6.99	126.37	2M-5173	Silicone (70)
-429	6.99	126.37	6V-5103	Fluorocarbon (FKM) (75)
-431	6.99	132.72	5H-9524	Nitrile (75)
-432	6.99	135.89	4F-7507	Nitrile (75)
-432	6.99	135.89	3E-6751	Fluorocarbon (FKM) (75)
-433	6.99	139.07	5H-6733	Nitrile (75)
-433	6.99	139.07	6H-1995	Silicone (70)
-433	6.99	139.07	6V-5167	Fluorocarbon (FKM) (75)
-436	6.99	148.59	5P-3620	Nitrile (75)
-436	6.99	148.59	003-2770	Nitrile (90)
-436	6.99	148.59	5D-6642	Silicone (70)
-436	6.99	148.59	5P-8861	Fluorocarbon (FKM) (75)
-437	6.99	151.77	8H-0273	Nitrile (75)
-437	6.99	151.77	6H-4162	Nitrile (90)
-437	6.99	151.77	6L-5473	Silicone (70)
-437	6.99	151.77	5P-8862	Fluorocarbon (FKM) (75)
-438	6.99	158.12	5L-5032	Nitrile (75)
-439	6.99	164.47	2H-6124	Nitrile (75)
-439	6.99	164.47	7M-6952	Silicone (70)
-439	6.99	164.47	6V-3968	Fluorocarbon (FKM) (75)
-440	6.99	170.82	5P-6619	EPDM (70)
-440	6.99	170.82	2D-1692	Nitrile (75)
-441	6.99	177.17	4F-9652	Nitrile (75)
-441	6.99	177.17	5D-7665	Silicone (70)
-441	6.99	177.17	6V-5095	Fluorocarbon (FKM) (75)
-442	6.99	183.52	2D-1690	Nitrile (75)
-442	6.99	183.52	7X-4810	Fluorocarbon (FKM) (75)
-443	6.99	189.87	5F-6222	Nitrile (75)
	6.99	199.26	2M-0338	Nitrile (75)

Attachment A-35

Table 37

O-RINGS (BY CROSS SECTION)
Dash Size (AS568A)	Section Dia. (mm)	Inside Dia. (mm)	Part Number	Material Name	Color
-445	6.99	202.57	2D-1691	Nitrile (75)
-445	6.99	202.57	6L-5360	Silicone (70)
-445	6.99	202.57	3P-0658	Fluorocarbon (FKM) (75)
-446	6.99	215.27	4F-7388	Nitrile (75)
-446	6.99	215.27	2N-6037	Polyacrylic (75) (ACM)
	6.99	218.50	6V-3603	Fluorocarbon (FKM) (75)
	6.99	224.79	4D-6548	Nitrile (75)
-447	6.99	227.97	1J-2890	Nitrile (75)
-447	6.99	227.97	7L-2176	Polyacrylic (75) (ACM)
-447	6.99	227.97	2S-2966	Silicone (70)
-448	6.99	240.67	1M-9015	Nitrile (75)
	6.99	253.37	3E-6794	Nitrile (75)
	6.99	253.37	1N-6000	Polyacrylic (75) (ACM)
-450	6.99	266.07	8F-8861	Nitrile (75)
	6.99	268.44	5P-3487	Nitrile (75)
	6.99	268.44	9X-7442	Fluorocarbon (FKM) (75)
-451	6.99	278.77	2H-6340	Nitrile (75)
-452	6.99	291.47	8H-8257	Nitrile (75)
-453	6.99	304.17	1W-0118	EPDM (70)
-453	6.99	304.17	4M-0661	Nitrile (75)
	6.99	310.13	4M-0737	Nitrile (75)
-454	6.99	316.87	8T-9047	Nitrile (75)
-454	6.99	316.87	4D-4508	Nitrile (75)
-454	6.99	316.87	6V-3967	Fluorocarbon (FKM) (75)
-455	6.99	329.57	5M-4454	Nitrile (75)
-456	6.99	342.27	5P-9217	Nitrile (75)
-456	6.99	342.27	6V-6638	Fluorocarbon (FKM) (75)
-457	6.99	354.97	4J-1253	Nitrile (75)
-458	6.99	367.67	6V-5862	Nitrile (75)
-459	6.99	380.37	8F-9960	Nitrile (75)
-460	6.99	393.07	5P-4342	Nitrile (75)
-461	6.99	405.26	8F-6498	Nitrile (75)
-462	6.99	417.96	4D-4503	Nitrile (75)
-463	6.99	430.33	3S-9896	Nitrile (75)
-466	6.99	468.76	8T-4811	Nitrile (75)
-467	6.99	481.46	5D-1071	Nitrile (75)
-468	6.99	494.16	2D-8363	Nitrile (75)
-468	6.99	494.16	6V-5060	Fluorocarbon (FKM) (75)

Attachment A-36

Table 38

O-RINGS (BY CROSS SECTION)
Dash Size (AS568A)	Section Dia. (mm)	Inside Dia. (mm)	Part Number	Material Name	Color
	6.99	520.07	5P-2587	Nitrile (75)
-470	6.99	532.26	3D-8241	Nitrile (75)
-472	6.99	582.68	2D-8364	Nitrile (75)
-473	6.99	608.08	5D-6428	Nitrile (75)
	7.16	18.47	5P-2428	Silicone (70)
	7.98	76.96	1L-7548	Polyacrylic (75) (ACM)
	9.00	216.20	8T-6690	Nitrile (75)
	8.40	154.50	095-1636	Nitrile (90)
	8.40	164.50	095-1637	Nitrile (90)
	8.40	179.50	095-1639	Nitrile (90)
	8.40	189.50	095-1565	Nitrile (75)
	8.40	199.50	095-1566	Nitrile (75)
	8.40	249.50	095-1643	Nitrile (90)
	8.40	384.50	095-1570	Nitrile (75)
	8.48	78.38	3H-4066	Nitrile (75)
	8.79	28.17	5H-4196	Nitrile (75)
	8.79	37.34	8F-2691	Nitrile (75)
	9.00	96.00	093-1342	Nitrile (70)
	9.47	48.34	8P-7003	Nitrile (60) (Toric Ring)
	9.47	48.34	7T-4087	Silicone (70) (Toric Ring)
	9.47	60.34	6P-8912	Nitrile (60) (Toric Ring)
	9.47	60.34	7T-1094	Silicone (70) (Toric Ring)
	9.47	66.09	1M-3097	Nitrile (60) (Toric Ring)
	9.47	66.09	2S-2181	Silicone (70) (Toric Ring)
	9.47	70.34	8P-0021	Nitrile (60) (Toric Ring)
	9.47	70.34	7T-1093	Silicone (70) (Toric Ring)
	9.47	76.34	8H-2262	Nitrile (60) (Toric Ring)
	9.47	76.34	9M-9730	Silicone (70) (Toric Ring)
	9.47	92.28	8H-2265	Nitrile (60) (Toric Ring)
	9.47	92.28	8S-5653	Silicone (70) (Toric Ring)
	9.47	102.34	6H-1309	Nitrile (60) (Toric Ring)
	9.47	102.34	5P-7145	Fluorocarbon (60) (Toric Ring)	Brt Blue
	9.47	102.34	3P-1847	Silicone (70) (Toric Ring)
	9.47	127.74	5P-9120	Nitrile (55) (Toric Ring)
	9.47	127.74	5P-7148	Fluorocarbon (60) (Toric Ring)	Brt Blue
	9.47	127.74	5P-2499	Silicone (70) (Toric Ring)
	9.52	70.10	1H-7683	Nitrile (75)
	9.52	196.85	3K-1516	Nitrile (75)

Attachment A-37

Table 39

O-RINGS (BY CROSS SECTION)
Dash Size (AS568A)	Section Dia. (mm)	Inside Dia. (mm)	Part Number	Material Name	Color
	10.00	140.00	093-1344	Nitrile (70)
	10.00	155.00	093-1345	Nitrile (70)
	10.00	175.00	093-1349	Nitrile (70)
	10.00	230.00	101-2154	Nitrile (70)
	11.43	300.61	9M-6097	Nitrile (60)
	11.43	326.00	4V-4884	Nitrile (60)
	12.55	262.69	1C-9746	Fluorocarbon (60) (Toric Ring)	Brt Blue
	12.70	147.47	4K-0173	Nitrile (60) (Toric Ring)
	12.70	147.47	3N-0801	Silicone (70) (Toric Ring)
	12.70	164.47	5P-3401	Silicone (70) (Toric Ring)
	12.70	166.47	7M-0475	Nitrile (60) (Toric Ring)
	12.70	184.95	2M-0344	Nitrile (60) (Toric Ring)
	12.70	184.95	9W-0055	Fluorocarbon (60) (Toric Ring)	Brt Blue
	12.70	184.95	3N-0759	Silicone (70) (Toric Ring)
	12.70	224.90	1M-9011	Nitrile (60) (Toric Ring)
	12.70	224.90	5P-1606	Silicone (70) (Toric Ring)
	12.70	232.80	9W-4097	Nitrile (55) (Toric Ring)
	12.70	232.80	9W-6612	Silicone (70) (Toric Ring)
	12.70	265.00	4M-0660	Nitrile (60) (Toric Ring)
	12.70	265.00	5P-1608	Silicone (70) (Toric Ring)
	12.70	280.03	7T-2457	Nitrile (60) (Toric Ring)
	12.70	317.13	4M-0736	Nitrile (60) (Toric Ring)
	12.70	317.13	3P-1849	Silicone (70) (Toric Ring)
	12.70	364.03	5P-4858	Nitrile (55) (Toric Ring)
	12.70	364.03	9W-5976	Silicone (70) (Toric Ring)
	12.70	424.65	5P-4946	Nitrile (55) (Toric Ring)
	12.70	424.65	9W-6613	Silicone (70) (Toric Ring)
	12.70	498.63	6Y-6333	ECO (60)
	12.70	498.63	5P-4062	Nitrile (55) (Toric Ring)
	12.70	498.63	5P-8403	Silicone (70) (Toric Ring)
	12.70	532.60	8E-6328	Nitrile (55) (Toric Ring)
	12.70	660.39	6V-2305	Silicone (70) (Toric Ring)
	12.70	820.58	6Y-8213	Silicone (70) (Toric Ring)
	12.75	666.65	1C-9456	Nitrile (55) (Toric Ring)
	14.28	650.00	9J-0818	Nitrile (60)
	15.88	600.00	6A-4503	Nitrile (60)
	15.88	660.40	5P-3228	Nitrile (60)
	15.88	751.84	8J-3699	Nitrile (60)

Material and Application Descriptions

Note: Each of the materials listed are broad, "Generic" Specifications encompassing many formulations, each one "fine-tuned" for specific applications. Some of the formulations used for Caterpillar O-rings are special for Caterpillar, and are not available in "off the shelf" O-rings. Make your selection of material based on the requirements of particular application.

Attachment B-1

Chloroprene Rubber (50) - 50 Durometer Chloroprene Rubber (70) - 70 Durometer

• Temperature Range (Continuous):

−40° to 100°C (−40.0° to 180.0°F)

• Typical Color: Black

• Compatible With:

- High aniline point oils

- Silicate esters

- Refrigerants (freons)

- Ammonia gas

- Weather/ozone resistant

- Freon®

• NOT Compatible With:

- Automotive and aircraft brake fluids

- Phosphate ester fluids

- Ketones

- Gasoline

- Aromatic and nitro hydrocarbons

• Typical Applications:

- Refrigeration

ECO (60) - 58-60 Durometer Epichlorohydrin

• Temperature Range (Continuous):

−40° to 120°C (−40.0° to 216.0°F)

• Typical Color: Black

• Compatible With:

- Petroleum fluids

- Ozone resistant

• NOT Compatible With:

- Brake fluids

- Esters

- Aldehydes

- Chlorinated and nitro hydrocarbons

- Ketones

• Typical Applications:

- Duo Cone toric rings

Attachment B-2

EPDM (50) - 50 Durometer Ethylene Propylene Diene Modified

• Temperature Range (Continuous):

−55° to 100°C (−67.0° to 180.0°F)

• Typical Color: Black

• Compatible With:

- Hydraulic fluids

- Automotive brake fluids

- Hot, cold water

- Steam (200° C (392.0° F) max)

- Some diluted acids

- Silicone fluids

- Phosphate ester fluids

- Ketones

- Alcohols

- Ozone

• NOT Compatible With:

- Petroleum fluids

- Diester Lubricants

- Aromatic fuels

• Typical Applications:

- Weather seals

- Gommets

- Boots

EPDM (70) - 70 Durometer Ethylene Propylene Diene Modified

• Temperature Range (Continuous):

−55° to 150°C (−67.0° to 270.0°F)

• Typical Color: Black

• Compatible With:

- Automotive brake fluids

- Hot, cold water

- Steam (200° C (392.0° F) max)

- Some diluted acids

- Silicone fluids

- Phosphate ester fluids

- Ketones

- Alcohols

- Ozone and sunlight

- Highly resistant to compression set

• NOT Compatible With:

- Petroleum fluids

- Diester Lubricants

- Aromatic fuels

• Typical Applications:

- Ebullient cooled engine cooling systems

Attachment B-3

Fluorocarbon (60) - (Toric Ring) 60 Durometer

• Temperature Range (Continuous):

−7° to 160°C (19.4° to 288.0°F)

• Typical Color: Black

• Compatible With:

- Petroleum fluids

- Diester Lubricants

- Some acids

- Phosphate ester fluids

- Highly resistant to compression set

- Silicone fluids

- Halogenated hydrocarbons (above 100° C (212.0° F))

- Ozone

- UV light

• NOT Compatible With:

- Methoxypropanol coolants (Dowtherm)

- Amines

- Ketones

- Esters

- Hot water

- Steam

- Brake fluids

• Typical Applications:

- High pressure, high temperature applications requiring resistance to air, water, fuels, lubricants, and hydraulic fluids

Fluorocarbon (FKM) (75) - (VITON) - 75 Durometer

• Temperature Range (Continuous):

−40° to 200°C (−40.0° to 360.0°F)

• Typical Color: Brown

• Compatible With:

- Petroleum fluids

- Diester Lubricants

- Some acids

- Phosphate ester fluids

- Ketones

- Highly resistant to compression set

- Silicone fluids

- Halogenated hydrocarbons (above 100° C (212.0° F))

• NOT Compatible With:

- Methoxypropanol coolants (Dowtherm)

- Amines

- Ketones

- Hot water

- Steam

- Brake fluids

• Typical Applications:

- High temperature applications requiring resistance to air, water, fuels, lubricants, and hydraulic fluids

Attachment B-4

Fluorocarbon (FKM) (90) - (VITON) - 90 Durometer

• Temperature Range (Continuous):

−25° to 200°C (−13.0° to 360.0°F)

• Typical Color: Green

• Compatible With:

- Petroleum fluids

- Diester Lubricants

- Some acids

- Phosphate ester fluids

- Highly resistant to compression set

- Silicone fluids

- Halogenated hydrocarbons (above 100° C (212.0° F))

• NOT Compatible With:

- Methoxypropanol coolants (Dowtherm)

- Amines

- Ketones

- Hot water

- Steam

- Brake fluids

• Typical Applications:

- High pressure, high temperature applications requiring resistance to air, water, fuels, lubricants, and hydraulic fluids

HNBR (72) - Highly Saturated Nitrile - 72 Durometer

• Temperature Range (Continuous):

−40° to 135°C (−40.0° to 243.0°F)

• Typical Color: Black

• Compatible With:

- Petroleum oils, greases

- Diester Lubricants

- Silicone fluids

- Water base engine coolants

- Steam

- Diesel Fuels

- Refrigerant HFC-134a (Non-Freon®)

- Highly resistant to compression set

- Ozone

- Abrasion resistant

• NOT Compatible With:

- Ketones

- Ethers

- Automotive and aircraft brake fluids

- Phosphate ester fluids

- Aromatic and nitro hydrocarbons

- Chlorinated hydrocarbons

• Typical Applications:

- High temperature power steering seals

- Higher temperature hydraulic seals

- Upper and lower cylinder liner seals

- Automotive air conditioner seals

- High temperature flex boot seals

Attachment B-5

Nitrile (55) (Toric Ring) - 55 Durometer

• Temperature Range (Continuous):

−20° to 105°C (−4.0° to 189.0°F)

• Typical Color: Black

• Compatible With:

- Petroleum base lubricants

- Water, water base engine coolants

- Silicone oils and greases

- Ethylene Glycol

- Alpha-Olefin base synthetic lubricants

• NOT Compatible With:

- Ketones

- Automotive and aircraft brake fluids

- Phosphate ester fluids

- Strong acids

- High levels of ozone

- UV light

• Typical Applications:

- Duo Cone seal toric ring

Nitrile (60) (Toric Ring) - 60 Durometer

• Temperature Range (Continuous):

−17° to 93°C (1.40° to 167.4°F)

• Typical Color: Black

• Compatible With:

- Petroleum base lubricants

- Water, water base engine coolants

- Silicone oils and greases

- Ethylene Glycol

- Alpha-Olefin base synthetic lubricants

• NOT Compatible With:

- Ketones

- Automotive and aircraft brake fluids

- Phosphate ester fluids

- Strong acids

- High levels of ozone

- UV light

• Typical Applications:

- Duo Cone seal toric ring

Nitrile (60) - 60 Durometer

• Temperature Range (Continuous):

−40° to 107°C (−40.0° to 192.6°F)

• Typical Color: Black

• Compatible With:

- Petroleum base lubricants

- Water, water base engine coolants

- Silicone oils and greases

- Ethylene Glycol

- Alpha-Olefin base synthetic lubricants

• NOT Compatible With:

- Ketones

- Automotive and aircraft brake fluids

- Phosphate ester fluids

- Strong acids

- High levels of ozone

- UV light

• Typical Applications:

- Hydraulic fluids

- Ambient temperature fuel handling

- Radiator thermostat seals

- Power steering seals

- High and low-pressure LPG service

Attachment B-6

Nitrile (70) - 70 Durometer

• Temperature Range (Continuous):

−40° to 107°C (−40.0° to 192.6°F)

• Typical Color: Black

• Compatible With:

- Petroleum base lubricants

- Water, water base engine coolants

- Silicone oils and greases

- Ethylene Glycol

- Alpha-Olefin base synthetic lubricants

- Hydrocarbon fuels

• NOT Compatible With:

- Ketones

- Acetone

- Automotive and aircraft brake fluids

- Phosphate ester fluids

- Strong acids

- Chlorinated hydrocarbons

- Nitro hydrocarbons

- High levels of ozone

- UV light

• Typical Applications:

- Hydraulic fluids

- Ambient temperature fuel handling

- Radiator thermostat seals

- Power steering seals

- High and low-pressure LPG service

Nitrile (75) - 75 Durometer

• Temperature Range (Continuous):

−40° to 107°C (−40.0° to 192.6°F)

• Typical Color: Black

• Compatible With:

- Petroleum base lubricants

- Water, water base engine coolants

- Silicone oils and greases

- Ethylene Glycol

- Alpha-Olefin base synthetic lubricants

- Excellent resistance to compression set

• NOT Compatible With:

- Ketones

- Automotive and aircraft brake fluids

- Phosphate ester fluids

- Strong acids

- High levels of ozone

- UV light

• Typical Applications:

- Hydraulic fluids (to 10335 kPa (1500.0 psi))

- Ambient temperature fuel handling

- Radiator thermostat seals

- Power steering seals

- High and low-pressure LPG service

Attachment B-7

Nitrile (80) - 80 Durometer

• Temperature Range (Continuous):

−40° to 107°C (−40.0° to 192.6°F)

• Typical Color: Black

• Compatible With:

- Petroleum base lubricants

- Water, water base engine coolants

- Silicone oils and greases

- Ethylene Glycol

- Alpha-Olefin base synthetic lubricants

- Hydrocarbon fuels

- Abrasion resistant

• NOT Compatible With:

- Ketones

- Automotive and aircraft brake fluids

- Phosphate ester fluids

- Strong acids

- High levels of ozone

- UV light

• Typical Applications:

- Hydraulic fluids (to 10335 kPa (1500.0 psi))

- Ambient temperature fuel handling

- Radiator thermostat seals

- Power steering seals

- High and low-pressure LPG service

Nitrile (90) - 90 Durometer

• Temperature Range (Continuous):

−34° to 107°C (−29.2° to 192.6°F)

• Compatible With:

- Petroleum base lubricants

- Water, water base engine coolants

- Silicone oils and greases

- Ethylene Glycol

- Alpha-Olefin base synthetic lubricants

- Hydrocarbon fuels

- Abrasion resistant

• NOT Compatible With:

- Ketones

- Automotive and aircraft brake fluids

- Phosphate ester fluids

- Strong acids

- High levels of ozone

- UV light

• Typical Applications:

- Hydraulic fluids (to 10335 kPa (1500.0 psi))

- Ambient temperature fuel handling

- Radiator thermostat seals

- Power steering seals

- High and low-pressure LPG service

Polyacrylate (75) - 75 Durometer

• Temperature Range (Continuous):

−34° to 150°C (−29.2° to 270.0°F)

• Typical Color: Black

• Compatible With:

- Petroleum base lubricants

- Automatic transmission fluid

- Resists flex cracking

• NOT Compatible With:

- Water or steam

- Methanol

- Ethylene glycol

- Brake fluids

- Phosphate ester fluids

• Typical Applications:

- Transmissions

- Power steering seals

Attachment B-8

Polyacrylate (75) (ACM) - 75 Durometer

• Temperature Range (Continuous):

−12° to 175°C (10.4° to 315.0°F)

• Typical Color: Black

• Compatible With:

- Petroleum base lubricants

- Transmission fluids

- Type "R" power steering fluid

- Excellent resistance to oxidation

- Excellent resistance to ozone

- Excellent resistance to sunlight and UV light

• NOT Compatible With:

- Water or steam

- Methanol

- Ethylene glycol

- Other alcohols

- Brake fluids

- Phosphate ester fluids

- Chlorinated hydrocarbons

- Aromatic hydrocarbons

• Typical Applications:

- Transmissions

- Power steering seals

Silicone (70) - 70 Durometer

• Temperature Range (Continuous):

−60° to 204°C (−76.0° to 367.2°F)

• Typical Color: Red

• Compatible With:

- Iso-butyl alcohol

- Diacetone alcohol

- Ethylene glycol

- Polyglycol

- High aniline point oils

- Extreme high/low temperatures

- Ozone and UV light

• NOT Compatible With:

- Aromatic hydrocarbons

- Petroleum oils

- Steam and hot water

- Low aniline point oils

- Ketones

- Acetone

- Abrasion

• Typical Applications:

- Duo Cone seal toric ring

- Brake seal ring

Silicone (70) - 70 Durometer, Silicone (70) (Toric Ring) - 70 Durometer

• Temperature Range (Continuous):

−46° to 170°C (−50.8° to 306.0°F)

• Typical Color: Yellow

• Compatible With:

- Air

- Water

- Silicone oils and greases

- High Aniline pint oil

- Good compression set resistance

• NOT Compatible With:

- Fuel Oil

- Gasoline

- EP oil

- Not tear or abrasion resistant

• Typical Applications:

- High temperature air seals

- Electrical system seals

- High temperature static grease seals

- Duo Cone Seals toric rings

Attachment B-9

Silicone (70) (VMQ) - 70 Durometer

• Temperature Range (Continuous):

−54° to 163°C (−65.2° to 293.4°F)

• Typical Color: Off-White

• Compatible With:

- Air

- Water

- Ethylene Glycol

- Polyglycol

- Diacetone alcohol

- High Aniline pint oil

- Ozone

- UV light

- Good compression set resistance

• NOT Compatible With:

- Fuel Oil

- Gasoline

- EP oil

- Ketones

- Acetone

- Steam and hot water

- Not tear or abrasion resistant

• Typical Applications:

- High temperature air seals

- Electrical system seals

- High temperature static grease seals

- Duo Cone Seals toric rings

Urethane (90) - 90 Durometer

• Temperature Range (Continuous):

−40° to 93°C (−40.0° to 167.4°F)

• Typical Color: Amber

• Compatible With:

- Excellent tear, extrusion, and abrasion resistance

- Petroleum base lubricants and hydraulic fluids/fuels

- Ozone

- UV light

• NOT Compatible With:

- Water

- Water base hydraulic fluids

• Typical Applications:

- Hydraulic cylinder seals

- Brake seals

Attachment B-10

XNBR - 80 Durometer Carboxylated Nitrile

• Temperature Range (Continuous):

−54° to 163°C (−65.2° to 293.4°F)

• Typical Color: Black

• Compatible With:

- Petroleum base lubricants

- Water, water base engine coolants

- Silicone oils and greases

- Ethylene Glycol

- Alpha-Olefin base synthetic lubricants

- Good resistance to low temperature brittleness

- Good resistance to compression set

- Good resistance to abrasion

• NOT Compatible With:

- Ketones

- Automotive and aircraft brake fluids

- Phosphate ester fluids

- Strong acids

- High levels of ozone

• Typical Applications:

- Hydraulic fluids (above 10335 kPa (1500.0 psi))

- Ambient temperature fuel handling

- Radiator thermostat seals

- Power steering seals

- High and low-pressure LPG service

Attachment C-1

Backup Rings

Illustration 8	g02795785

Table 40

Dash Size (AS568A)	Dim "B" (mm)	Inside Dia. (mm)	Dim "C" (mm)	Dim "D" (mm)	Part Number	Material Name
-006	1.35	3.56	1.14	1.19	031-3347	Nitrile (90)
-007	1.35	4.34	1.14	1.19	030-6117	Nitrile (90)
-008	1.35	5.14	1.14	1.19	030-6118	Nitrile (90)
-009	1.35	5.94	1.14	1.19	030-6119	Nitrile (90)
-010	1.35	6.73	1.14	1.19	030-6120	Nitrile (90)
-012	1.35	9.91	1.14	1.19	9X-7741	Fluorocarbon (FKM) (90)
-012	1.35	9.91	1.14	1.19	030-6121	Nitrile (90)
-013	1.35	10.82	1.14	1.19	9J-0705	Nitrile (90)
	1.35	13.16	1.14	1.19	7X-4776	Nitrile (90)
	1.35	13.89	1.14	1.19	008-5592	Nitrile (90)
	1.35	14.73	1.14	1.19	6V-3505	Nitrile (90)
-016	1.35	16.33	1.14	1.19	5P-2199	Nitrile (90)
	1.35	21.08	1.14		2Y-4536	Nitrile (90)
-111	2.18	11.48	1.14	1.19	6v-3956	Fluorocarbon (FKM) (90)
-114	2.18	16.26	1.14	1.19	8T-8885	Nitrile (90)
-116	2.18	19.43	1.14	1.19	004-4576	Nitrile (90)
-117	2.18	21.11	1.14		5P-7857	Nitrile (90)
-118	2.18	22.68	1.14	1.19	9J-0240	Nitrile (90)
-119	2.18	24.28	1.14	1.19	6V-3838	Fluorocarbon (FKM) (90)
-119	2.18	24.28	1.14		5P-7858	Nitrile (90)
-122	2.18	29.03	1.14	1.19	6V-1941	Fluorocarbon (FKM) (90)
-124	2.18	32.21	1.14	1.19	7J-6288	Nitrile (90)
-125	2.18	33.81	1.14	1.19	5P-9685	Nitrile (90)
-127	2.18	36.98	1.14	1.19	6J-2418	Nitrile (90)
-129	2.18	40.16	1.14	1.19	5P-9686	Nitrile (90)
-131	2.18	43.33	1.14	1.19	5P-9687	Nitrile (90)
-133	2.18	46.51	1.14	1.19	6V-3300	Nitrile (90)
-135	2.18	49.68	1.14	1.19	8T-4946	Nitrile (90)
-139	2.18	56.03	1.14	1.19	6V-3299	Nitrile (90)
	2.39	33.33		1.27	9J-7252	Urethane (90)
	2.90	44.36		1.09	1S-0670	Urethane (90)
-228	2.90	56.69		1.09	030-3239	Urethane (90)

Attachment C-2

Backup Rings

Illustration 9	g02795788

Table 41

Dash Size (AS568A)	Dim "B" (mm)	Inside Dia. (mm)	Dim "C" (mm)	Dim "D" (mm)	Part Number	Material Name
-230	2.90	63.30		1.09	4J-9225	Urethane (90)
-232	2.90	69.61		1.09	6J-5731	Urethane (90)
-234	2.90	75.92		1.09	8J-2574	Urethane (90)
-236	2.90	82.23		1.09	4J-9224	Urethane (90)
-238	2.90	88.55		1.09	1S-0669	Urethane (90)
-240	2.90	94.86		1.09	2K-6830	Urethane (90)
-242	2.90	101.17		1.09	5J-7865	Urethane (90)
-244	2.90	107.48		1.09	1K-7095	Urethane (90)
-246	2.90	113.79		1.09	2J-3961	Urethane (90)
-248	2.90	120.11		1.09	2K-4096	Urethane (90)
-250	2.90	126.42		1.09	2J-7767	Urethane (90)
	2.90	129.58		1.09	030-6141	Urethane (90)
-252	2.90	132.73		1.09	2K-2961	Urethane (90)
	2.90	139.10		1.09	8T-8434	Urethane (90)
-256	2.90	145.35		1.09	2K-3258	Urethane (90)
-258	2.90	151.66		1.09	4J-9223	Urethane (90)
-259	2.90	157.98		1.09	2K-4473	Urethane (90)
-261	2.90	170.60		1.09	4J-9218	Urethane (90)
-262	2.90	176.91		1.09	2K-2940	Urethane (90)
	2.90	183.40		1.00	4T-3107	Urethane (90)
-264	2.90	189.52		1.09	3J-9742	Urethane (90)
	2.90	202.16		1.09	2J-0744	Urethane (90)
	2.90	208.60		1.00	1U-1101	Urethane (90)
-270	2.90	227.41		1.09	3J-8466	Urethane (90)
-271	2.90	233.72		1.09	3J-2688	Urethane (90)
-274	2.90	252.66		1.09	4J-1151	Urethane (90)
	2.90	259.20		1.00	3G-6857	Urethane (90)
-275	2.90	265.28		1.09	8J-8880	Urethane (90)
	2.90	271.80		1.09	9X-4596	Urethane (90)
-210	3.00	19.46	1.02	1.09	030-6122	Nitrile (90)
-211	3.00	21.03	1.02	1.09	031-0646	Nitrile (90)
-212	3.00	22.63	1.02	1.09	030-6123	Nitrile (90)

Attachment C-3

Backup Rings

Illustration 10	g02795861

Table 42

Dash Size (AS568A)	Dim "B" (mm)	Inside Dia. (mm)	Dim "C" (mm)	Dim "D" (mm)	Part Number	Material Name
-213	3.00	24.21	1.02	1.09	3K-7863	Nitrile (90)
-214	3.00	25.18	1.02	1.09	4K-4759	Nitrile (90)
-215	3.00	27.38	1.02	1.09	3K-7219	Nitrile (90)
-217	3.00	30.56	1.02	1.09	3K-8692	Nitrile (90)
-218	3.00	31.34	1.02	1.09	030-7588	Nitrile (90)
-219	3.00	33.88	1.02	1.09	030-6125	Nitrile (90)
-221	3.00	37.06	1.02	1.09	3K-8699	Nitrile (90)
-222	3.00	38.66	1.02	1.09	6V-1557	Fluorocarbon (FKM) (90)
-222	3.00	38.66	1.02	1.09	4J-9222	Nitrile (90)
-224	3.00	45.00	1.02	1.09	6V-1556	Fluorocarbon (FKM) (90)
-225	3.00	48.18	1.02	1.09	6J-1021	Nitrile (90)
-226	3.00	51.36	1.02	1.09	5J-0605	Nitrile (90)
-227	3.00	54.53	1.02	1.09	030-6129	Nitrile (90)
	3.00	57.71	1.02	1.09	9X-7552	Nitrile (90)
-229	3.00	60.88	1.02	1.09	7J-6287	Nitrile (90)
	3.00	64.06	1.02	1.09	6V-1555	Fluorocarbon (FKM) (90)
-231	3.00	66.83	1.02	1.09	6J-2420	Nitrile (90)
-233	3.00	73.18	1.02	1.09	6V-1558	Fluorocarbon (FKM) (90)
-233	3.00	73.18	1.02	1.00	1S-0668	Nitrile (90)
-235	3.00	79.53	1.02	1.09	6J-1381	Nitrile (90)
-237	3.00	85.88	1.02	1.09	2J-4066	Nitrile (90)
	3.00	89.05	1.02		2Y-8973	Nitrile (90)
-239	3.00	92.23	1.02	1.09	4J-9219	Nitrile (90)
-241	3.00	98.58	1.02	1.09	1K-7098	Nitrile (90)
-243	3.00	104.93	1.02	1.09	4J-9220	Nitrile (90)
-247	3.00	117.63	1.02	1.00	030-6140	Nitrile (90)
-249	3.00	124.28	1.02	1.09	4J-9221	Nitrile (90)
-253	3.00	136.98	1.02	1.09	030-6142	Nitrile (90)
-255	3.00	143.33	1.02	1.09	5J-0604	Nitrile (90)
-257	3.00	149.68	1.02	1.09	2K-8256	Nitrile (90)
-263	3.00	184.61	1.02	1.09	5P-3235	Nitrile (90)
-265	3.00	197.31		1.09	5J-6444	Nitrile (90)

Attachment C-4

Backup Rings

Illustration 11	g02795867

Table 43

Dash Size (AS568A)	Dim "B" (mm)	Inside Dia. (mm)	Dim "C" (mm)	Dim "D" (mm)	Part Number	Material Name
-267	3.00	210.01	1.02	1.09	4J-6557	Nitrile (90)
	3.00	260.81	1.02	1.09	5J-6787	Nitrile (90)
-350	4.30	117.28		1.52	9J-7861	Urethane (90)
-354	4.30	129.91		1.52	8J-1689	Urethane (90)
-358	4.30	142.53		1.52	8J-1717	Urethane (90)
-361	4.30	155.15		1.52	7J-8955	Urethane (90)
	4.30	174.25		1.50	1U-1738	Urethane (90)
-366	4.30	186.21		1.52	8J-0548	Urethane (90)
	4.30	227.75		1.52	1U-3173	Urethane (90)
	4.30	243.75		1.52	1U-3307	Urethane (90)
	4.30	256.40		1.52	1U-1770	Urethane (90)
	4.30	281.70		1.50	1U-1626	Urethane (90)
	4.30	294.05		1.50	3E-6793	Urethane (90)
	4.30	300.64		1.50	8T-6926	Urethane (90)
	4.30	307.00		1.50	1U-3383	Urethane (90)
	4.30	352.00		1.52	4T-4127	Urethane (90)
	4.32	199.52		1.52	3G-3747	Urethane (90)
-318	4.65	25.73	1.52		3P-1205	Nitrile (90)
-324	4.65	35.26	1.52		3P-1204	Nitrile (90)
-325	4.65	38.43	1.52	1.65	030-6127	Nitrile (90)
-326	4.65	41.61	1.52	1.65	030-6128	Nitrile (90)
-327	4.65	44.78	1.52	1.65	5P-2134	Nitrile (90)
-328	4.65	47.96	1.52	1.65	030-5087	Nitrile (90)
-330	4.65	54.31	1.52	1.65	030-3114	Nitrile (90)
-332	4.65	60.78	1.52	1.65	030-6131	Nitrile (90)
-334	4.65	67.13	1.52	1.65	030-6133	Nitrile (90)
-335	4.65	70.31	1.52	1.65	3P-1207	Nitrile (90)
-339	4.65	83.13	1.52	1.65	030-3117	Nitrile (90)
-340	4.65	86.31	1.52	1.09	5P-0911	Nitrile (90)
-342	4.65	92.66	1.52	1.65	5J-3934	Nitrile (90)
-343	4.65	95.83	1.52		3P-1206	Nitrile (90)
-346	4.65	105.49	1.52	1.65	8J-3752	Nitrile (90)

Attachment C-5

Backup Rings

Illustration 12	g02795872

Table 44

Dash Size (AS568A)	Dim "B" (mm)	Inside Dia. (mm)	Dim "C" (mm)	Dim "D" (mm)	Part Number	Material Name
-347	4.65	108.66	1.52		5P-0910	Nitrile (90)
-348	4.65	111.84	1.52		5P-8921	Nitrile (90)
-348	4.65	111.84	1.52		9X-7278	Urethane (90)
	4.65	124.54	1.52	1.65	6V-5659	Nitrile (90)
-353	4.65	127.71	1.52	1.65	068-9001	Nitrile (90)
-252	4.65	132.73	1.14	1.19	2K-2961	Urethane (90)
-355	4.65	134.06	1.52		5P-0909	Nitrile (90)
	4.65	149.94	1.52	1.65	6V-5658	Nitrile (90)
	4.65	167.28		1.52	9X-7273	Urethane (90)
	4.65	200.74	1.52	1.65	8J-4385	Nitrile (90)
	4.65	338.80		1.52	9X-4595	Urethane (90)
-362	5.33	158.12			7J-8955	Urethane (90)
-367	5.33	189.87			8J-0548	Urethane (90)
-375	5.33	240.67			1U-3307	Urethane (90)
-377	5.33	253.37			1U-1770	Urethane (90)
-379	5.33	278.77			1U-1626	Urethane (90)
-381	5.33	304.17			1U-3383	Urethane (90)
-382	5.33	329.57			9X-4595	Urethane (90)
-432	6.00	136.98	2.44	2.61	030-6143	Nitrile (90)
-434	6.00	144.17	2.44	2.61	030-4538	Nitrile (90)
-436	6.00	150.52	2.44	2.61	030-6145	Nitrile (90)
-440	6.00	172.06	2.44		065-7978	Nitrile (90)
	6.00	353.20		2.45	4T-5929	Urethane (90)
	6.00	396.12		2.40	9X-4615	Urethane (90)
	6.23	220.89		2.40	3E-6783	Urethane (90)
	6.23	227.20		2.40	3E-6784	Urethane (90)
	6.40	265.00		2.40	3E-6795	Urethane (90)
-454	6.99	316.87			6V-3580	Urethane (90)
-457	6.99	354.97			4T-5929	Urethane (90)
	9.52	221.00		4.72	6E-0250	XNBR (80)