C13 Engine for Combat and Tactical Vehicles Caterpillar


Exhaust Manifold

Usage:

C13 EMS


Illustration 1g02781480

(1) Torque for taperlock studs ... 38 ± 5 N·m (28 ± 4 lb ft)

Note: Before applying sealant, the male and the female ends of the exhaust manifold must be free of the following substances:dirt, rust, grease and oil. Apply a thin coat of 2P-2333 High Temperature Sealer to the outside diameter of the male ends and inside diameter of the female ends of the exhaust manifolds. Remove excess sealer from the assembled joint.

(3) Install the gaskets with the tabs downward on all six exhaust ports.

Note: Before assembly, apply Loctite# 51008 C5A CO BSE A/S on the washer faces and to the 12 threads of the exhaust manifold .

Note: Use assembly spacers at positions 11, 7 and 9 to align the exhaust manifolds. Remove the assembly spacers before final assembly.

(2) Tighten locknuts 1 through 12 in the numerical tightening sequence shown in Illustration 1 to 55 ± 5 N·m (41 ± 4 lb ft).

Caterpillar Information System:

2011/12/01 An Improved 5P-8500 Key Is Now Available {1416, 1416, 7000, 7000}
Diesel Particulate Filter Regeneration on C7.1 Engines{108F} Diesel Particulate Filter Regeneration on C7.1 Engines{108F}
New Engine Software Is Available for Tier 4 Interim C9.3 Through C18 Industrial and Machine Engines{1901, 1902, 1920} New Engine Software Is Available for Tier 4 Interim C9.3 Through C18 Industrial and Machine Engines{1901, 1902, 1920}
Revised Start-Up Procedure For Uninterruptible Power Supply UPSB 125/130 {4480} Revised Start-Up Procedure For Uninterruptible Power Supply UPSB 125/130 {4480}
2012/01/12 A New Hose Is Used in the Fuel Filter Lines on C175-16 Generator Set Engines {1261, 1274}
2011/12/19 New Fuel Injectors and New Software Are Used for C175-16 Generator Set Engines {1251, 1254, 1290, 1713, 1901, 1920}
C7 and C9 On-highway Engines Fluid Recommendations
C7 and C9 On-highway Engines Refill Capacities
C13 and C15 On-Highway Engines Reference Information
C7 and C9 On-highway Engines Plate Locations and Film Locations
2011/12/15 Procedure to Remedy Loose V-belts on Certain C12 Marine Engines {1207, 1358, 1359, 1397}
C7 and C9 On-highway Engines Product Description
9U-5000 Series Hydraulic Test Bench {0599, 0738} 9U-5000 Series Hydraulic Test Bench {0599, 0738}
C7 and C9 On-highway Engines Maintenance Interval Schedule - C7 Engines with Deep Sumps that are Used in School Bus Applications
C7 and C9 On-highway Engines Maintenance Interval Schedule - C7 Engines with Shallow Sumps that are Used in School Bus Applications
4C-9910 Portable Hydraulic Tester (Flow 125 GPM) {0599, 0784, 5050, 5057, 5095} 4C-9910 Portable Hydraulic Tester (Flow 125 GPM) {0599, 0784, 5050, 5057, 5095}
C7 and C9 On-highway Engines Air Compressor - Check
C7 and C9 On-highway Engines Compression Brake - Inspect/Adjust/Replace - Cat Compression Brake
CX48-P2300 Petroleum Transmission Transmission Relief Valve (Transmission Hydraulic Control)
CX48-P2300 Petroleum Transmission Transmission Flexible Coupling
CX48-P2300 Petroleum Transmission Transmission Flexible Coupling
CX48-P2300 Petroleum Transmission Transmission Flexible Coupling
2012/01/06 New Location for the Air Inlet Temperature Sensor on C175-16 Generator Set Engines {1439, 7400}
C11 and C13 Engines Camshaft
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.