C27 and C32 Engines for Caterpillar Built Machines Caterpillar


Camshaft Bearings - Remove and Install

Usage:

826K 2L3

Removal Procedure

Table 1
Required Tools    
Tool     Part Number     Part Description     Qty    
A     8S-2241     Camshaft Bearing Tool Group     1    
B     9U-7222     Camshaft Bearing Pilot     1    
8M-8778 Taperlock Stud
1/2 - 13 by 1 9/16 inch    
1    
C     9U-7210     Puller Plate     1    

Start By:

  1. Remove the camshaft.


NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.





    Illustration 1g01159745

  1. Remove the No. 7 camshaft bearing (rear). Work from the rear of the engine to the front of the engine.

  1. Install the small end of Tooling (B) in camshaft bearing (1) .

  1. Position Tooling (C) over Tooling (A). Install Tooling (A) through the cylinder head on Tooling (B) .

    Note: Tooling (C) is installed on the outside of the cylinder head. Tooling (C) is required in order to remove all the camshaft bearings from the cylinder head.

  1. Use Tooling (A) to remove camshaft bearing (1) from the cylinder head.

  1. Remove Tooling (B) from Tooling (A) and remove the camshaft bearing.

Installation Procedure

Table 2
Required Tools    
Tool     Part Number     Part Description     Qty    
A     8S-2241     Camshaft Bearing Tool Group     1    
B     9U-7222     Camshaft Bearing Pilot     1    
8M-8778 Taperlock Stud
1/2 - 13 by 1 9/16 inch    
1    
C     9U-7210     Puller Plate     1    
D     9U-7223     Alignment Bushing     1    
E     9U-7213     Backup Plate     1    
0S-1621 Bolt
1/2 - 13 by 1 inch    
1    
F     9U-7214     Spacer Plate     1    


NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.





    Illustration 2g01159754

  1. Install the No. 7 camshaft bearing (rear), as follows:

    1. Insert the large end of Tooling (B) into the No. 7 camshaft bore.

    1. Position Tooling (C) over Tooling (A). Install Tooling (A) through the cylinder head on Tooling (B) .

    1. Position camshaft bearing (1) on Tooling (B). Install Tooling (E) on Tooling (B) .

      Note: Refer to Specifications, "Cylinder Head" for appropriate information for the orientation of the camshaft bearings in the cylinder head.

    1. Use Tooling (A) in order to pull camshaft bearing (1) into the camshaft bore.

      Note: When the chamfer of Tooling (E) contacts the face of the camshaft bore, the camshaft bearing is properly installed.




    Illustration 3g01159756

  1. Install the No. 6 through No. 2 camshaft bearings, as follows:

    1. Insert the large end of Tooling (B) into the camshaft bore.

      Note: Use Tooling (D) to align Tooling (A) and Tooling (B) with the camshaft bearing bores. Install Tooling (D) in the inside diameter of any installed camshaft bearing between Tooling (A) and Tooling (B) .

    1. Install Tooling (A) on Tooling (B). Position camshaft bearing (1) on Tooling (B). Install Tooling (E) on Tooling (B) .

      Note: Refer to Specifications, "Cylinder Head" for appropriate information for the location and the orientation of the camshaft bearings in the cylinder head.

    1. Use Tooling (A) in order to pull camshaft bearing (1) into the camshaft bore.

      Note: When the chamfer of Tooling (E) contacts the face of the camshaft bore, the camshaft bearing is properly installed.




    Illustration 4g01159758

  1. Install the No. 1 camshaft bearing (front), as follows:

    1. Insert the large end of Tooling (B) into the No. 1 camshaft bore. Assemble Tooling (A) and Tooling (D) on Tooling (B) .

    1. Position camshaft bearing (1) on Tooling (B). Install Tooling (E) and Tooling (F) on Tooling (B) .

      Note: Refer to Specifications, "Cylinder Head" for appropriate information for the location and the orientation of the camshaft bearings in the cylinder head.

      Note: Tooling (F) is used to seat the No. 1 camshaft bearing to the correct depth in the camshaft bore.

    1. Use Tooling (A) in order to pull the No. 1 camshaft bearing into the No. 1 camshaft bore. When the chamfer of Tooling (E) contacts the face of the camshaft bore, the camshaft bearing is properly installed.

End By: Install the camshaft.

Caterpillar Information System:

C27 and C32 Engines for Caterpillar Built Machines Camshaft - Remove and Install - C27
C27 and C32 Engines for Caterpillar Built Machines Camshaft - Remove and Install
521B and 522B Track Feller Bunchers Machine Systems Pressure Reducing Valve (Feed Reduction) Test and Adjust - Signal Limiter Valve
C18 Generator Sets Mounting and Dismounting
299D and 299D XHP Compact Track Loaders and 272D and 272D XHP Skid Steer Loaders Machine Electronic Control System Electrical Input Components
C27 and C32 Engines for Caterpillar Built Machines Rocker Arm and Shaft - Remove and Install
C27 and C32 Engines for Caterpillar Built Machines Valve Actuator (Variable) - Remove and Install
789D Off-Highway Truck Speed Sensor (Transmission)
793F CMD Off-Highway Truck/Tractor Braking System Electronic Control Module (ECM)
2011/11/11 New Mounting Bolts Update the Wheel Group on Certain 797 Off-Highway Trucks {4006, 4251, 7200}
Cat® Terrain Office Software Consumable Management
259D, 279D, 289D, 299D, 299D XHP, 299D2 and 299D2 XHP Compact Track Loaders, 257D, 277D, 287D, 297D, 297D XHP, 297D2 and 297D2 XHP Multi Terrain Loaders and 236D, 242D, 246D, 262D, 272D, 272D XHP, 272D2 and 272D2 XHP Skid Steer Loaders Piston Pump (Hydrostatic)
Bench Test Procedure for a R2900G and R3000H Load Haul Dump Transmission {3030, 3030, 3073} Bench Test Procedure for a R2900G and R3000H Load Haul Dump Transmission {3030, 3030, 3073}
PL87 Pipelayer Hydraulic System Accumulator - Test and Charge
C27 and C32 Engines for Caterpillar Built Machines Engine Oil Pan - Remove and Install - Multiple Oil Pan
789D Off-Highway Truck Torque Converter Hydraulic System
793F CMD Off-Highway Truck/Tractor Braking System Diagnostic Code List
C27 and C32 Engines for Caterpillar Built Machines Cylinder Liner - Remove and Install
C27 and C32 Engines for Caterpillar Built Machines Pistons and Connecting Rods - Remove and Install
C27 and C32 Engines for Caterpillar Built Machines Connecting Rod Bearings - Remove and Install
C27 and C32 Engines for Caterpillar Built Machines Crankshaft Main Bearings - Remove and Install
C27 and C32 Engines for Caterpillar Built Machines Crankshaft - Remove and Install
C27 and C32 Engines for Caterpillar Built Machines Atmospheric Pressure Sensor - Remove and Install
299D and 299D XHP Compact Track Loaders and 272D and 272D XHP Skid Steer Loaders Machine Electronic Control System Electrical Output Components
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.