Diesel Particulate Filter Active Regeneration Was Interrupted
此步骤涉及以下诊断代码:
Show/hide table
柴油微粒滤清器(DPF)主动再生的诊断故障代码中止     | ||
J1939 代码     | 说明     | 备注     |
5319-31     | 后处理 1 柴油微粒滤清器再生未完成     | 电子控制模块(ECM)中止了主动再生。 主动再生的最大持续时间已超过三次。 如有配备,警告灯将闪烁。 发动机将减额。 ECM 将会记录此诊断代码。 成功主动再生后,该代码变为非现行状态。     |
执行下述步骤:
建议的措施
注: 下面以概率的先后顺序列出了这些步骤。 依次完成这些步骤。
Show/hide table
故障诊断与排除测试步骤     | 数值     | 结果     |
---|---|---|
1. 诊断代码 A. 建立电子维修工具和电子控制模块 (ECM) 之间的通信。 B. 检查有无现行诊断代码。     |
代码     |
结果:激活或记录了故障诊断代码。 继续此步骤之前,先对可能导致再生不成功的所有诊断代码进行故障诊断与排除。 结果:未激活或记录故障诊断代码。 转至测试步骤 2。     |
2. 排气管上的绝缘层(如有配备) A. 检查发动机和清洁排放模块(CEM)之间排放管上的绝缘层。 确保绝缘层没有缺失或损坏。     |
隔垫     |
结果:绝缘层缺失或损坏。 修理或更换排气管上的绝缘层。 结果:绝缘层正常。 转至测试步骤 3。     |
3. 排气泄漏 A. 彻底检查发动机和 CEM 之间的排气管有无泄漏。 确保所有连接牢固且没有泄漏。     |
排气泄漏     |
结果:排气泄漏。 进行必要修理,并确认通过修理排除了故障。 结果:排气管正常。 继续测试步骤 4。     |
4. 手动再生 A. 使用以下方法之一执行手动再生: · 应用上的"强制再生"开关(如有配备) · 电子维修工具上的"微粒滤清器强制再生" B. 使用电子维修工具清除所有记录的诊断代码。     |
完成再生     |
结果:再生成功完成且没有主动再生代码。 将发动机重新投入使用。 结果:再生未成功完成。 请联系代理商解决方案网络 (DSN)。     |
Caterpillar Information System:
Model HCS-40 Hydraulic Cylinder Servicer{0374, 0599, 0700, 0738, 7562} Model HCS-40 Hydraulic Cylinder Servicer{0374, 0599, 0700, 0738, 7562}
CT660 CX31 and CX31 HT On Highway Truck Power Train Electronic Control System Electronic Control Unit - Flash Program
C13, C15, and C18 Tier 4 Final Engines Cylinder Head
320 GC, 320 and 323 Excavator Machine Systems Specifications Refrigerant Compressor
3512C and 3516C Marine Auxiliary and Generator Set Engines Fumes Disposal Filter Element - Replace
CT660 CX31 and CX31 HT On Highway Truck Power Train Electronic Control System Transmission - Calibrate
3512C Petroleum Engines Data Link Configuration Status - Test
2011/10/10 A New Charging Alternator Group Is Used on C18 Engines In Certain Products {1405}
319-2187 Diesel Particulate Filter (DPF) Cleaner {0374, 0599, 0680, 0701, 0702, 108D} 319-2187 Diesel Particulate Filter (DPF) Cleaner {0374, 0599, 0680, 0701, 0702, 108D}
2011/12/15 A New Service Tool for Installing the Service Sleeve Bearings in Hydraulic Gear Pumps Is Now Available for Certain CAT Machines {0738, 5073, 5073, 7551}
Installation of the 324-7875 Control Box Gp for G3600 Engines {1917, 1924, 4460, 7426} Installation of the 324-7875 Control Box Gp for G3600 Engines {1917, 1924, 4460, 7426}
320E and 323E Excavators Machine System Specifications Boom Lines
2011/10/28 Correct Orientation of the V-Band Clamp on the Center Housing/Turbine Housing Joint Is Needed on Certain C15 Truck Engines {1052, 1053}
3500 Generator Sets Engine Air Cleaner Element (Dual Element) - Inspect/Clean/Replace
3500 Generator Sets Engine Air Cleaner Element (Single Element) - Inspect/Clean/Replace
3500 Generator Sets Engine Air Precleaner - Check/Clean
3516C Industrial Engine Product Lifting
2011/11/16 A New Turbocharger Water Line Is Used for Certain 3516B and 3516C Engines {1380}
2011/12/23 Special Instruction, REHS7409, "Initial Start-Up of CG137 and G3300B Engines" Is Available {1000}
3516C Marine Engine Engine Operation
2011/10/19 Improved Bolts and Washers Along with a New Procedure Are Used to Fasten the Pilot to the Lockup Clutch Housing {3101, 7553}
2011/12/14 A New Engine Oil Cooler Bypass Is Used for C175-16 Engines {1307}
320E and 323E Excavators Machine System Specifications Travel Motor Guard
320E and 323E Excavators Machine System Specifications Swivel