Cylinder Head
Show/hide table
| |
| 图 1 | g02648477 |
Show/hide table
| 274-1953 缸盖总成和 235-2974 缸盖总成技术规格 | |||
| 项目 | 数量 | 零件 | 技术规格说明 |
| - | - | - | 以下螺栓为 以下螺栓为 在螺栓的螺纹上和硬垫圈两侧涂抹 6V-4876 润滑剂。 按照下列步骤拧紧缸盖的螺栓： 按数字次序拧紧螺栓 1 到螺栓 26 至 按数字次序拧紧螺栓 1 到螺栓 26 至 再次按数字次序拧紧螺栓 1 到螺栓 26 至 缸盖的平整度都应在总体 |
Show/hide table
| |
| 图 2 | g02548900 |
Show/hide table
| 274-1953 缸盖总成和 235-2974 缸盖总成技术规格 | |||
| 项目 | 数量 | 零件 | 技术规格说明 |
| A | - | - | 缸盖厚度：
新缸盖的厚度为 使用后的缸盖的最小厚度为 |
Show/hide table
| |
| 图 3 | g02548907 |
|
(1) 套筒轴承接头
(2) 机油道 (3) 机油孔 (4) 套筒轴承 | |
Show/hide table
| 注意 |
|---|
|
必须把凸轮轴轴承安装到正确位置。 不这样做的话可能导致发动机损坏。 |
Show/hide table
| |
| 图 4 | g02548916 |
Show/hide table
| 274-1953 缸盖总成和 235-2974 缸盖总成技术规格 | |||
| 项目 | 数量 | 零件 | 技术规格说明 |
| B | - | - | 套筒轴承接头的方位为水平面以上 20 ± 5 度 |
| C | - | - | 凸轮轴套筒轴承的孔为 |
Show/hide table
| |
| 图 5 | g02548921 |
Show/hide table
| 274-1953 缸盖总成和 235-2974 缸盖总成技术规格 | |||
| 项目 | 数量 | 零件 | 技术规格说明 |
| 4 | 7 | 216-5582 衬套 | 套筒轴承的安装深度是很重要的。 将套筒轴承安装到以下深度：
尺寸 (D)： 尺寸 (E)： 尺寸 (F)： 尺寸 (G)： 尺寸 (H)： 尺寸 (J)： 尺寸 (K)： |
Show/hide table
| |
| 图 6 | g02742717 |
Show/hide table
| 274-1953 缸盖总成和 235-2974 缸盖总成技术规格 | |||
| 项目 | 数量 | 零件 | 技术规格说明 |
| 5 | - | - | 组装前，将 4C-9506 固定胶涂抹在六个喷油器套筒的下端压装直径上。
将喷油器套筒压到面 (6) 的底部。 |
| V | - | - | 杯塞的安装深度为 |
| W | - | - | 杯塞的安装深度为 |
Caterpillar Information System:
320 GC, 320 and 323 Excavator Machine Systems Specifications Refrigerant Compressor
3512C and 3516C Marine Auxiliary and Generator Set Engines Fumes Disposal Filter Element - Replace
CT660 CX31 and CX31 HT On Highway Truck Power Train Electronic Control System Transmission - Calibrate
3512C Petroleum Engines Data Link Configuration Status - Test
2011/10/10 A New Charging Alternator Group Is Used on C18 Engines In Certain Products {1405}
319-2187 Diesel Particulate Filter (DPF) Cleaner {0374, 0599, 0680, 0701, 0702, 108D} 319-2187 Diesel Particulate Filter (DPF) Cleaner {0374, 0599, 0680, 0701, 0702, 108D}
2011/12/15 A New Service Tool for Installing the Service Sleeve Bearings in Hydraulic Gear Pumps Is Now Available for Certain CAT Machines {0738, 5073, 5073, 7551}
Installation of the 324-7875 Control Box Gp for G3600 Engines {1917, 1924, 4460, 7426} Installation of the 324-7875 Control Box Gp for G3600 Engines {1917, 1924, 4460, 7426}
320E and 323E Excavators Machine System Specifications Boom Lines
320E and 323E Excavators Machine System Specifications Boom Cylinder Lines
312F and 313F Excavators Plate Locations and Film Locations
3512C and 3516C Marine Auxiliary and Generator Set Engines Gauges and Indicators
CT660 CX31 and CX31 HT On Highway Truck Power Train Electronic Control System Electronic Control Unit - Flash Program
Model HCS-40 Hydraulic Cylinder Servicer{0374, 0599, 0700, 0738, 7562} Model HCS-40 Hydraulic Cylinder Servicer{0374, 0599, 0700, 0738, 7562}
C3.4B Engines Diesel Particulate Filter Active Regeneration Was Interrupted
2011/10/28 Correct Orientation of the V-Band Clamp on the Center Housing/Turbine Housing Joint Is Needed on Certain C15 Truck Engines {1052, 1053}
3500 Generator Sets Engine Air Cleaner Element (Dual Element) - Inspect/Clean/Replace
3500 Generator Sets Engine Air Cleaner Element (Single Element) - Inspect/Clean/Replace
3500 Generator Sets Engine Air Precleaner - Check/Clean
3516C Industrial Engine Product Lifting
2011/11/16 A New Turbocharger Water Line Is Used for Certain 3516B and 3516C Engines {1380}
2011/12/23 Special Instruction, REHS7409, "Initial Start-Up of CG137 and G3300B Engines" Is Available {1000}
3516C Marine Engine Engine Operation
2011/10/19 Improved Bolts and Washers Along with a New Procedure Are Used to Fasten the Pilot to the Lockup Clutch Housing {3101, 7553}