Engine Oil Pump
Show/hide table
Illustration 1 | g02724345 |
Show/hide table
Specification for 6N-1030 Engine Oil Pump Gp | |||
Item | Qty | Part | Specification Description |
Before operation, the pump must be lubricated with clean engine oil and the pump must turn freely by hand. | |||
A | 1 | 4N-5273 Pump Drive Shaft | Diameter of pump drive shaft is Bore in the 7N-0285 Oil Pump Cover for bushing for pump drive shaft is |
B | 1 | 1W-7240 Gear | Length of the gear is |
Depth of bore for the gear is |
|||
1 | 1 | 2S-2760 Spring | Length under test force is |
Test force is |
|||
Approximate free length after test is |
|||
2 | 2 | 7N-2156 Bushing | Install the bushings, so that the bushings are even with the outside of the oil pump body.
Angle from the centerline of the oil pump body to the bushing joint of the bushing is 30 ± 15 degrees. |
D | 2 | 8M-8489 Dowel | Extension of the dowel after installation is |
E | 1 | - | Installation depth of bushing in the oil pump housing is |
Show/hide table
Illustration 2 | g02724342 |
Show/hide table
Specification for 6N-1030 Engine Oil Pump Gp | |||
Item | Qty | Part | Specification Description |
3 | 2 | 8S-6511 Bushing | Flush the bushing with the face of the pump cover. |
Angle (F) from the centerline of the pump cover to the bushing joint of the bushing is 30 ± 15 degrees. |
Caterpillar Information System:
CG137-08 and CG137-12 Generator Sets Exhaust Bypass Valve
C27 Generator Set Control Panel - Inspect/Test
TH55-E70 and TH55-E90 Petroleum Transmissions Transmission Planetary - Assemble
TH55-E70 and TH55-E90 Petroleum Transmissions Transmission Planetary - Disassemble
3500 Generator Sets Coolant Level - Check
349F and 352F Excavators Hydraulic System Automatic Travel Speed Control - Test
3500 Generator Sets Coolant (ELC) - Change
3500 Generator Sets Coolant (DEAC) - Change
3512, 3508 and 3516 Generator Sets Refill Capacities
G3512 EPA Emergency and Non-Emergency Standby Generator Sets Generator Lead Connections
2011/09/28 New Rocker Arm Assemblies Are Available for Certain C15 Truck Engines {1102, 1123}
G3500 Valve Runout Tool{0760, 1100, 1101, 1103, 1104, 1105} G3500 Valve Runout Tool{0760, 1100, 1101, 1103, 1104, 1105}
C3.4B Industrial Engine Stopping the Engine
3500 Generator Sets Coolant Temperature Regulator - Replace
C1.5 and C2.2 Industrial Engines Monitoring System - Engine Warning Indicators
C27 Generator Set Manual Stop Procedure
3516C Generator Sets Before Starting Engine
XQ400 Power Module Maintenance Recommendations
Using the U5MK1110 Ampseal Connector Kit for Wiring Harness Repairs on Perkins Engines{0374, 0599, 0701, 0709} Using the U5MK1110 Ampseal Connector Kit for Wiring Harness Repairs on Perkins Engines{0374, 0599, 0701, 0709}
Idler/Roller Assembly Machine{0374, 0599, 0729, 4159, 4180} Idler/Roller Assembly Machine{0374, 0599, 0729, 4159, 4180}
Base-Mounted Recirculating Parts Washers{0374, 0599, 0680, 0699, 0700} Base-Mounted Recirculating Parts Washers{0374, 0599, 0680, 0699, 0700}
C3.4B Engines Inlet Air Is Restricted
2011/10/13 Service Replacement Bolts and Seal Washers Are Available for the High-Pressure Fuel Pump on C175-16 Engines {1251, 1290, 7553}
3516C Generator Set Engines Coolant Temperature Is Low