C13, C15, and C18 Tier 4 Final Engines Caterpillar


Engine Oil Filter Base

Usage:

826K 232


Illustration 1g02678338
Bolt tightening sequence for oil filter base

Table 1
Specification for 363-7616 Engine Oil Filter Gp 
Item  Qty  Part  Specification Description 
1R-1808 Engine Oil Filter  Apply clean lubricating oil to the gasket of the engine oil filter. 
Tighten the 209-7291 Oil Filter Base As bolts in a numerical sequence as shown in the Illustration 1 to the standard torque. 


Illustration 2g02678340


Illustration 3g02678341

Table 2
Specification for 363-7616 Engine Oil Filter Gp 
Item  Qty  Part  Specification Description 
242-3864 Spring  Length under test force is 43.18 mm (1.700 inch)
Test force is 43.7 N (9.8 lb).
Free length after test is 58.50 ± 0.50 mm (2.303 ± 0.020 inch).
2P-4304 Hollow Stud  Torque to 68 ± 7 N·m (50 ± 5 lb ft)
Length for applying red Loctite 271 to the threads of the hollow stud is 10.0 ± 1.5 mm (0.39 ± 0.06 inch)

Caterpillar Information System:

C9.3 Tier 4 Final Engines Engine Oil Filter Base
C4.4 Marine Generator Set Emergency Stopping
TA19 M4WD Agricultural Transmission Transmission System
TA19 M4WD Agricultural Transmission General Information
Retrofitting a Cat 270 Air Compressor with a BA-921 CR Air Compressor on Certain C13 and C15 On-Highway Engines{1803} Retrofitting a Cat 270 Air Compressor with a BA-921 CR Air Compressor on Certain C13 and C15 On-Highway Engines{1803}
2011/08/04 Correction to Troubleshooting, SENR6493 , "3512 Engine Oil Well Service" {1265, 1901}
3516C Generator Set Engines Sensor Signal (Analog, Passive) - Test
C4.4 Marine Generator Set Generator Set Vibration - Test/Record
C4.4 Marine Generator Set Product Description
C3.4B Industrial Engine Engine Oil Pan - Cast Iron Oil Pan
C3.4B Engines For Caterpillar Built Machines Fan Drive
C9.3 Tier 4 Final Engines Camshaft
C3.4B Engines For Caterpillar Built Machines Electronic Control Module
Retrofitting for Ultra Lean Burn (ULB) on a G3512 Engine{1000, 775E} Retrofitting for Ultra Lean Burn (ULB) on a G3512 Engine{1000, 775E}
C27 and C32 Industrial Engines Auxiliary Drive (Front) - Remove and Install
3516C Generator Set Engines Sensor Signal (PWM) - Test
C27 and C32 Industrial Engines Auxiliary Drive (Front) - Disassemble
C27 and C32 Industrial Engines Auxiliary Drive (Front) - Assemble
CG137-08 and CG137-12 Industrial Engines Sensor Signal (Analog, Active) - Test
Checking the High-Pressure Relief Valve for Leakage on C6.6 and C4.4 Engines{1288} Checking the High-Pressure Relief Valve for Leakage on C6.6 and C4.4 Engines{1288}
TA19 M4WD Agricultural Transmission Location of Electronic Components for Transmission System
2013/08/21 A New Oversized Cylinder Bore Liner Seal Insert Is Available for 3500 Engine Cylinder Block Salvage {1201, 7555}
3516C Generator Set Engines Sensor Supply - Test
C27 Generator Set Electronic Modular Control Panel 4 (EMCP 4) - EMCP 4.3/4.4
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.