High Pressure Screens - Clean/Replace - If Equipped
There are a total of six hydraulic screens on your machine. If the system becomes contaminated or if a major failure occurs, clean the screens. If a screen is damaged, replace the screen.
Show/hide table
Illustration 1 | g02585040 |
The screen for the steering pump is located inside the access door directly behind the cab.
Show/hide table
Illustration 2 | g02670136 |
There are two screens for the implement pump that are located inside the rear frame near the articulation joint. These screens are accessible from the right side of the machine.
Show/hide table
Illustration 3 | g02670416 |
The screen for the brake pump is located behind the hydraulic tank on the left side of the machine.
Show/hide table
Illustration 4 | g02670158 |
The screens for the fan pump and the fan motor are located behind the fan guard on the rear of the machine.
- Stop the engine.
- Remove the drain plug at the bottom of the filter housing. Allow the oil to drain into a suitable container.
- Use a strap type wrench to remove the filter housing.
- Remove the high-pressure screens from the filter housing.
- Clean the screen, the drain plug, the filter housing, and the filter housing base with a clean, nonflammable solvent. Allow the components to dry.
- Install the screen and the drain plug in the filter housing.
- Install the filter housing on the filter housing base.
- Start the engine. Make sure that the parking brake is engaged.
- Operate the steering, the brakes, and the attachment in order to circulate the oil. Check the high-pressure screens for leaks.
- Stop the engine.
Caterpillar Information System:
854K Wheel Dozer Electrohydraulic System Pilot Control Actuator Current (Proportional Solenoid) - Check
924K, 930K and 938K Wheel Loaders Electrohydraulic System Gear Pump (Hydraulic Fan)
854K Wheel Dozer Electrohydraulic System Electronic Control Module (ECM) - Configure
854K Wheel Dozer Electrohydraulic System Electronic Control Module (ECM) - Flash Program
966M and 972M Wheel Loaders Visibility Information
992K Wheel Loader and 854K Wheel Dozer Power Train Torque Converter and Pump Drive Housing
621H, 623H and 627H Wheel Tractor-Scrapers Power Train Transmission Hydraulic Control Valve - Disassemble - Tractor
992K Wheel Loader Electrohydraulic System MID 082 - CID 1326 - FMI 02
992K Wheel Loader Electrohydraulic System MID 082 - CID 0967 - FMI 14
992K Wheel Loader Electrohydraulic System MID 082 - CID 0967 - FMI 09
992K Wheel Loader and 854K Wheel Dozer Power Train Torque Converter and Transmission Pressures
Weld Repair Procedure for 990H Wheel Loader Main Hydraulic Tank{0679, 5056, 5068} Weld Repair Procedure for 990H Wheel Loader Main Hydraulic Tank{0679, 5056, 5068}
854K Wheel Dozer Electrohydraulic System System Pressure - Release
854K Wheel Dozer Electrohydraulic System Pressure Tap Locations
854K Wheel Dozer Electrohydraulic System Lift Double Stall Speed with Stall Detection (Electronic Technician) - Check
D9T Track-Type Tractor Machine Systems Pilot Control Valve - Remove and Install
Product Link - PL522/523 MID 161 - CID 3766- FMI 14
854K Wheel Dozer Electrohydraulic System Pressure Reducing Valve Pressure for Dead Engine Pilot Supply (Engine OFF) - Test and Adjust
854K Wheel Dozer Electrohydraulic System Pilot Control Actuator Pressure - Check
D9T Track-Type Tractor Power Train Torque Converter Outlet Relief Valve - Remove
992K Wheel Loader Electrohydraulic System Ride Control Signal Pressure - Check
992K Wheel Loader Electrohydraulic System Piston Pump (Implement) Main Relief Valve Pressure - Test and Adjust
D9T Track-Type Tractor Power Train Torque Converter Outlet Relief Valve - Install
621H, 623H and 627H Wheel Tractor-Scrapers Engine Supplement Battery - Remove and Install - Scraper