Cylinder Head
Show/hide table
 | |
| 图 1 | g03330706 |
螺栓拧紧顺序 | |
Show/hide table
| 346-0485 缸盖总成 的技术规格 | |||
| 项目 | 数量 | 零件 | 技术规格说明 |
| 1 | 26 | 290-6884 缸盖紧固件总成 | 按照以下步骤拧紧缸盖螺栓： 请参阅图 1 中的缸盖螺栓拧紧顺序。 装配前，使用清洁的发动机机油轻轻润滑螺栓螺纹。 1. 按照数字顺序，将螺栓 1 至螺栓 26 拧紧至扭矩为 160 ± 15 N·m (118 ± 11 lb ft)。 2. 按照数字顺序，再次将螺栓 1 至螺栓 26 拧紧至扭矩为 160 ± 15 N·m (118 ± 11 lb ft)。 3. 在螺栓 1 至螺栓 26 上做一个标记。 按数字顺序将螺栓 1 到螺栓 26 拧紧 90 度（1/4 圈）。 4. 松开螺栓 1 至螺栓 26，直到螺栓头下方的垫圈松动。 5. 按照数字顺序，将螺栓 1 至螺栓 26 拧紧至扭矩为 160 ± 15 N·m (118 ± 11 lb ft)。 6. 按照数字顺序，再次将螺栓 1 至螺栓 26 拧紧至扭矩为 160 ± 15 N·m (118 ± 11 lb ft)。 7. 在螺栓 1 至螺栓 26 上做一个标记。 按数字顺序将螺栓 1 到螺栓 26 拧紧 90 度（1/4 圈）。 8. 按照数字顺序，将螺栓 27 至螺栓 32 拧紧至扭矩为 28 ± 7 N·m (21 ± 5 lb ft)。 |
| 2 | 6 | 9X-6000 螺栓 | |
| - | - | - | 新缸盖的高度为 163.00 ± 0.15 mm (6.417 ± 0.006 in)。 |
Show/hide table
 | |
| 图 2 | g03330707 |
Show/hide table
| 项目 | 数量 | 零件 | 技术规格说明 |
| 3 | 5 | 8M-5860 杯塞 | 安装前，将 Loctite 11358 涂抹到杯塞的孔上。 |
| 4 | 6 | 3B-0623 杯塞 | 安装前，将 Loctite 11358 涂抹到杯塞的孔上。 |
| 5 | 3 | 8M-5860 杯塞 | 安装前，将 Loctite 11358 涂抹到杯塞的孔上。 |
| 6 | 1 | 8M-5860 杯塞 | 安装前，将 Loctite 11358 涂抹到杯塞的孔上。 |
| 7 | 6 | 310-7258 O 形密封圈 | 装配前，向孔上涂覆清洁的发动机机油。 |
| 8 | 6 | 310-7259 O 形密封圈 | 装配前，向孔上涂覆清洁的发动机机油。 |
| 9 | 6 | 325-6575 喷油器套筒 | 装配前，向喷油器衬套外表面上涂覆距离为 (H) 的绿色 Loctite 620。 |
| E | - | - | 杯塞 (3) 的安装长度为 1.25 ± 0.25 mm (0.049 ± 0.010 in)。 |
| F | - | - | 杯塞 (4) 的安装长度为 3.75 ± 0.50 mm (0.148 ± 0.020 in)。 |
| G | - | - | 杯塞 (5) 的安装长度为 1.00 ± 0.50 mm (0.039 ± 0.020 in)。 |
Caterpillar Information System:
C13, C15, and C18 Tier 4 Final Engines Cylinder Head Valves
G3500B Engines Exhaust Bypass Valve - Wastegate
345D MHPU and 349D MHPU Mobile Hydraulic Power Units Daily Inspection
2011/08/09 New Relay and Relay Socket Are Now Used with EMCP3 Control Panel On Certain 3406C and C18 Generator Sets {4490, 4493}
C3.4B Engines for Caterpillar Built Machines Engine Oil Pump - Inspect
C3.4B Engines for Caterpillar Built Machines Engine Valve Lash - Inspect
C3.4B Engines for Caterpillar Built Machines Fuel Injection Timing - Check
C3.4B Engines for Caterpillar Built Machines Air in Fuel - Test
C3.4B Engines for Caterpillar Built Machines Finding Top Center Position for No. 1 Piston
C3.4B Engines for Caterpillar Built Machines Valve Guide - Inspect
C9.3 Tier 4 Final Engines Fuel Injector
3516C Generator Sets Burn Prevention
2013/08/21 Calculating Cylinder Liner Projection for 3500, 3500B, 3500C, and G3500 Engines {1201, 1216}
Correct Combinations of Connecting Rods Allowed in Remanufactured Cylinder Packs for Certain C13 Engines{1218, 1225, 1239} Correct Combinations of Connecting Rods Allowed in Remanufactured Cylinder Packs for Certain C13 Engines{1218, 1225, 1239}
3516C Generator Set Engines Emergency Stop - Test
3406C Industrial Engine Safety Messages
3516C Generator Set Engines Prelubrication - Test
A New V-Band Clamp and New Turbochargers Are Used in Certain 789C, 793C, and 793D Off-Highway Truck Engines with Low Altitude Arrangements {1052, 1053} A New V-Band Clamp and New Turbochargers Are Used in Certain 789C, 793C, and 793D Off-Highway Truck Engines with Low Altitude Arrangements {1052, 1053}
3500 Industrial Engines Fuel Priming Pump
3516C Generator Set Engines Fumes Disposal Filter
3516C Generator Set Engines Fumes Disposal Group
3516C Generator Set Engines Jacket Water Heater
3516C Generator Set Engines Turbocharger Exhaust Temperature Sensor
3516C Generator Set Engines Air Cleaner