Product Link - PL522/523 Caterpillar


MID 161 - CID 1888 - FMI 14

Usage:

769C 01X
产生此代码的情况:

当 PL522 和 523 中的诊断电路检测到 GPS 天线系统中存在故障时,系统将会记录此诊断代码。

测试步骤 1. 通过 CATERPILLAR 电子技师 (CAT ET) 访问 PL522 或 523。

  1. 将 Cat ET 维修工具连接到机器上。

  1. 确认存在 ECM(VIMS 主模块)。

预期结果:

存在 ECM(VIMS 主模块)。

结果:

  • 正常 - 存在 ECM(VIMS 主模块)。 转至测试步骤 3。

  • 异常 - Cat ET 屏幕上没有 ECM(VIMS 主模块)。

    修复: 确认 PL522 或 523 的导线是否已正确安装。 利用万用表检查导线。 如果不存在 ECM(VIMS 主模块),请参考系统操作、故障诊断与排除、测试和调整, "电子维修工具不与 ECM 通信"。

    停止

测试步骤 2. 确认机器是否已经移动

确认自上一已知的位置报告起,机器移动量是否超过了所配置的最小距离。

预期结果:

机器未移动。

结果:

  • 正常 - 自上一已知的位置报告起,机器移动量小于所配置的最小距离。 因此,机器未发送任何位置报告。停止

  • 异常 - 机器的移动情况不明。 转至测试步骤 3。

测试步骤 3. 确认 PRODUCT LINK 模块处于电源模式 1。

  1. 选择 Cat ET 的 "Status Parameters(状态参数)"。

  1. 确认 "Power Mode Status(电源模式状态)"为 "Power Mode 1(电源模式 1)"。 确认 "Key Switch Status(钥匙开关状态)"为 "On(接通)"。

预期结果:

机器处于 "Power Mode 1(电源模式 1)"和 "Key Switch On(钥匙开关接通)"状态。

结果:

  • 正常 - Cat ET 的屏幕显示 "Power Mode 1(电源模式 1)"。 转至测试步骤 4。

  • 异常 - Cat ET 屏幕不正常。 转至测试步骤 4。

测试步骤 4. 确认 GPS 接收器功能正常。

  1. 选择 Cat ET 的 "GPS Information(GPS 信息)"。

  1. 确认 "GPS Position Status(GPS 位置状态)"为 "Valid(有效)"。

  1. 确认 GPS 已在配置时间("GPS 坐标有效持续时间")内计算出了位置。 通过 "GPS 时间标志"和 "PC 当前日期/时间"的比较,可以计算出自上一位置计算至今的时间。

  1. 选择 "Status Parameters(状态参数)"。 确认 "GPS Receiver(GPS 接收器)"处于 "Functional(工作)"状态。

预期结果:

"GPS Position Status(GPS 位置状态)"为 "Valid(有效)"。 上一位置计算 (GPS) 位于 "Power Mode 1(电源模式 1)"下的配置时间长度("GPS 坐标有效持续时间")内。

结果:

  • 正常 - Cat ET 屏幕上的指示正常。 GPS 接收器功能正常。 转至测试步骤 6。

  • 异常 - "GPS Information(GPS 信息)"上的指示不正常。 转至测试步骤 5。

  • 异常 - "GPS Receiver(GPS 接收器)"上的指示不是 "Functional(工作)"。 转至测试步骤 5。

测试步骤 5. 确认天线的中心导体未与屏蔽间短路。

  1. 断开模块上的 GPS 天线连接。

  1. 测量天线电缆屏蔽到电缆中心导体间的电阻。 屏蔽是接头的螺纹部分。

关于以下信息,请参考系统操作、故障诊断与排除、测试和调整, "报告和信息不可用":

  • 显示电阻检查的插图

  • 天线电阻检查列表

  • 电阻值列表

预期结果:

GPS 天线的电阻满足系统操作、故障诊断与排除、测试和调整, "报告和信息不可用"中定义的技术规格。

结果:

  • 正常 - 电阻值正确。 转至测试步骤 6。

  • 异常 - 电阻异常。

    修复: 天线电缆或天线存在中心导体与外部屏蔽间的短路。 通过断开天线上的电缆隔离短路。 更换天线组件。 确认模块工作正确。

    停止

测试步骤 6. 确认信息发送。

  1. 确认 "Message Transmission Timestamp(信息发送时间标志)"为最新。 如果时间标志为 1984,则表明模块未曾发送信息。

  1. 确认 "Cellular Network Coverage Status(移动通信网络覆盖状态)"在 Cat ET 的 "GSM Information(GSM 信息)"内。

  1. 进入 Cat ET 内的下拉菜单并选择 "Service(维修)"。 随后选择 "PLM Commands(PLM 指令)"和 "Fuel Report(燃油报告)"。 燃油报告将提供位置更新。

结果:

  • 正常 - PL522 或 523 看上去工作正常。 确认办公室成功接收信息。 牢记延时长短取决于办公室的软件配置。停止

  • 异常 - 天线或模块有故障。 在确认天线和电缆前不要更换模块。

    修复: 请参考故障诊断与排除, "报告和信息不可用"。

    停止

Caterpillar Information System:

773G and 775G Off-Highway Truck Cooling System Coolant (ELC) - Change
XQ125 Generator Set Product Installation
777G Off-Highway Truck Traction Control System (TCS) - Test
C27 Generator Set Product Storage
XQ125 Generator Set Electrical System
735B, 740B and 740B EJECTOR Articulated Trucks Machine Systems Steering Check and Combiner Valve - Assemble
777G Off-Highway Truck Secondary Steering - Test
SH-56B Felling Head Felling Head Hydraulic Cylinder (Accumulator Arm) - Remove and Install
735B, 740B and 740B EJECTOR Articulated Trucks Machine Systems Steering Check and Combiner Valve - Disassemble
SH-56B Felling Head Felling Head Hydraulic Cylinder (Grapple Arm) - Remove and Install
Using the 1U-8860 Large Engine Blowby Pickup Group and the 8T-2700 Blowby/Airflow Indicator{0781, 0785, 1000} Using the 1U-8860 Large Engine Blowby Pickup Group and the 8T-2700 Blowby/Airflow Indicator{0781, 0785, 1000}
SH-56B Felling Head Felling Head Piston Motor (Disc Saw) - Remove and Install
SH-56B Felling Head Felling Head Grapple Arm - Remove
773G and 775G Off-Highway Truck Cooling System Coolant Sample (Level 1) - Obtain
773G and 775G Off-Highway Truck Cooling System Coolant Sample (Level 2) - Obtain
XQ60 Rental Generator Set After Starting Engine
C175-16 Locomotive Engine Engine Oil Pressure Sensor
773G and 775G Off-Highway Truck Cooling System Pressure Cap - Clean/Replace
2570C and 2670C Wheel Feller Bunchers Monitoring System
735B, 740B and 740B EJECTOR Articulated Trucks Engine Supplement Exhaust Bellows - Remove and Install
773G and 775G Off-Highway Truck Cooling System Water Temperature Regulator - Replace
2012/12/24 Triple Flange Idler Available for Compact Track Loader {4159}
2011/11/08 The Breather for Steering Tank Is Now Relocated on 793F Off-Highway Trucks {5057}
SH-56B Felling Head Felling Head Accumulator Arm - Remove and Install
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.