3500C Marine Engines Caterpillar


Gear Group (Front)

Usage:

3512C 2A2


图 1g02645057

表 1
376-3358 前齿轮总成的技术规格 
项目  数量  零件  技术规格说明 
144-8263 惰齿轮组件  安装后, 140-9597 衬套的孔径为 90.000 ± 0.010 mm (3.5433 ± 0.0004 in)。 
安装长度为 2.3 ± 0.5 mm (0.09 ± 0.02 in)
新轴 (9) 的直径为 89.880 ± 0.020 mm (3.5386 ± 0.0008 in)
7N-5245 泵接头  安装后, 127-5400 衬套的孔径为 75.000 ± 0.055 mm (2.9527 ± 0.0022 in)。 
新泵传动轴 (5) 的直径为 74.900 ± 0.015 mm (2.9488 ± 0.0006 in)
8T-2153 内六角头调整螺钉  拧紧至扭矩为 6 ± 1 N·m (53 ± 9 lb in)。 
259-4598 O 形密封圈  利用所密封的润滑剂轻轻润滑内孔。 
278-4287 泵接头  安装后, 127-5400 衬套的孔径为 75.000 ± 0.055 mm (2.9527 ± 0.0022 in)。 
衬套必须与泵接头齐平。
235-3546 O 形密封圈  利用所密封的润滑剂轻轻润滑内孔。 
7C-3258 止推垫圈组件  厚度为 7.00 ± 0.15 mm (0.276 ± 0.006 in)。 
定位销 (B) 的突出量为 4.5 ± 0.5 mm (0.18 ± 0.02 in)

Caterpillar Information System:

3500 Engines Housing (Front)
G3406 Engine Engine Mounts - Inspect
CG137-08 and CG137-12 Engines Electric Starting Motor - Remove and Install
349F and 352F Excavators Machine System Specifications Sprocket
3500C Marine Engines Crankshaft
349F and 352F Excavators Machine System Specifications Fasteners - Swing Drive and Motor
3500B and 3500C Marine Engines Duplex Engine Oil Filters
3500 Engines Air Lines
3500 Engines Air Lines
G3406 Engine Crankcase Blowby - Test/Record
2011/07/22 Improved Caterpillar Digital Voltage Regulator (CDVR) Is Used for Certain C9, C15, C18, 3300, 3400, G3400, C27, C32, 3500, G3500, and C175 Engines {4467}
G3406 Engine Maintenance Interval Schedule - Turbocharged Aftercooled Engines
2011/10/06 Warning Film Is Available for the High Pressure Fuel Pump on C175-16 Engines {1251, 1290, 7405}
G3406 Engine Fuel Filter Differential Pressure - Check
CG137-08 and CG137-12 Industrial Engines Speed/Timing (Primary) - Test
CG137-08 and CG137-12 Engines Gas Pressure Regulator - Remove and Install
G3406 Engine Spark Plugs - Inspect/Adjust/Replace
2011/09/12 A New Gasket and a New Spacer Plate are Now Used on Certain Reman 3500 Engines {1100, 1201, 7555}
2011/07/14 Glow Plugs on Certain C6.6 Engines {1412}
CG137-08 and CG137-12 Industrial Engines Speed/Timing (Secondary) - Test
Repair Procedure for Damaged Harness Wiring {1408} Repair Procedure for Damaged Harness Wiring {1408}
345B Excavator Machine System Specifications Track Roller Mounting
C11, C13, and C15 On-highway Engines Maintenance Interval Schedule - C11 , C13 , and C15 Engines with Standard (Deep) Oil Sumps
C11, C13, and C15 On-highway Engines Maintenance Interval Schedule - C11 and C13 Engines with Optional Shallow Oil Sumps
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.