Cylinder Head
Show/hide table
| |
| 图 1 | g02574259 |
Show/hide table
| 223-7263 缸盖的技术规格 | |||
| 项目 | 数量 | 零件 | 技术规格说明 |
| 1 | 16 | 124-1855 螺栓 | 使用以下步骤拧紧缸盖螺栓：
以下螺栓的长度为 以下螺栓的长度为 1. 在螺栓的螺纹上和硬垫圈两侧涂抹 6V-4876 润滑剂。 2. 按照数字顺序，将螺栓 1 至螺栓 26 拧紧至扭矩为 3. 按照数字顺序，将螺栓 1 至螺栓 26 拧紧至扭矩为 4. 按照数字顺序，再次将螺栓 1 至螺栓 26 拧紧至扭矩为 |
| 2 | 10 | 124-1854 螺栓 | |
Show/hide table
| |
| 图 2 | g02981060 |
|
俯视图 | |
Show/hide table
| 项目 | 数量 | 零件 | 技术规格说明 |
| 3 | 20 | 3B-0645 杯塞 | 在装配前，将高强度或高温厌氧法兰密封胶涂抹到表面上。
安装深度为 |
| 4 | 12 | 3B-0623 杯塞 | 在装配前，将高强度或高温厌氧法兰密封胶涂抹到表面上。
安装深度为 |
| 5 | 6 | 263-4920 喷油器套筒 | 在装配前，将绿色 Loctite 620 涂抹到喷油器套筒下端的压配合直径上。
压装喷油器套筒，直至喷油器套筒在端面 (6) 处触底。 |
| 7 | 5 | 3B-0623 杯塞 | 在装配前，将高强度或高温厌氧法兰密封胶涂抹到表面上。
安装深度为 |
Show/hide table
| |
| 图 3 | g02981062 |
|
剖面 A-A | |
Show/hide table
| 项目 | 数量 | 零件 | 技术规格说明 |
| - | 7 | 216-5582 衬套 | 参考图 3 以了解凸轮轴衬套的安装深度：
尺寸 (H) 为 尺寸 (J) 为 尺寸 (K) 为 尺寸 (L) 为 尺寸 (M) 为 尺寸 (N) 为 尺寸 (P) 为 |
Show/hide table
| |
| 图 4 | g02981061 |
Show/hide table
| 项目 | 数量 | 零件 | 技术规格说明 |
| R | - | - | 凸轮轴衬套的孔径为 |
| S | - | - | 衬套接合处的方向是水平面以上 20 ± 5 度。 |
| - | - | - | 新缸盖的厚度为 |
Caterpillar Information System:
C13, C15, and C18 Tier 4 Final Engines Cylinder Head Valves
3406C Generator Sets Plate Locations and Film Locations
3500B Locomotive Engines Crankshaft
3500 Engines Crankshaft
3500 Engines Connecting Rod and Main Bearing Journals
C27 and C32 Engines for Caterpillar Built Machines Gear Group (Front)
CX31 and CX31 HT On-Highway Transmissions Transmission Planetary
3406C Engines for Caterpillar Built Machines Engine Oil Pump
3500B Engines and 776D, 777D, 784C, 785C, 789C, 793C and 793D Off-Highway Truck/Tractors Connecting Rod
C175-16 Marine Propulsion Engines Exhaust Flange
C175-16 Marine Propulsion Engines Exhaust Flange
C15 On-highway Engine Connecting Rod
Caterpillar Service Welding Guide {0374, 0599, 0677, 0678, 0679} Caterpillar Service Welding Guide {0374, 0599, 0677, 0678, 0679}
Communication Adapter II{0600, 0709, 7600, 7610} Communication Adapter II{0600, 0709, 7600, 7610}
Replacing Sleeve Bearings in Tyrone Gear Pumps and Motors (Used on Series 7 and 8, Iron and Aluminum Housings){0738, 5061, 5073, 7551} Replacing Sleeve Bearings in Tyrone Gear Pumps and Motors (Used on Series 7 and 8, Iron and Aluminum Housings){0738, 5061, 5073, 7551}
Network Management Card with Modbus for the UPSB505 Uninterruptible Power Supply Administration: Security
C13, C15, and C18 Tier 4 Final Engines Camshaft
CX31 and CX31 HT On-Highway Transmissions Transmission Hydraulic Control
G3406 Engine Coolant - Change
C15 and C18 Industrial Engines Vibration Damper
C27 and C32 Engines for Caterpillar Built Machines Housing (Rear)
3500 Industrial Engines Crankshaft
C175-16 Marine Propulsion Engines Vibration Damper Guard
C27 and C32 Engines for Caterpillar Built Machines Housing (Front)