Optimized Seat Controls
Show/hide table
图 1 | g02481937 |
(1) 背垫角度手柄 (2) 前/后手柄 (3) 乘坐区指示器 (4) 高度/重量调整 (5) 乘坐硬度调整 |
提起背垫角度手柄 (1) ,并使背垫弹簧在背垫内向前或向后倾斜。 在所需位置松开手柄。
提起前/后手柄 (2) ,以前后移动座椅。 在几个位置之一处松开手柄。
应当利用乘坐区指示器 (3) 来确定悬架是否调整得过高或过低。 调整悬架高度,直到黑线位于指示器窗口的中间位置。
利用高度和重量调整开关 (4) 升起悬架。 向左按摇臂开关可升起座椅,而向右按可降下座椅。
要想执行乘坐硬度调整 (5) ,下推操纵杆可增加乘坐硬度。 上拉操纵杆可降低硬度。 在几个位置之一处松开操纵杆。
座垫调整
Show/hide table
图 2 | g02481481 |
(6) 座垫倾斜 |
通过凹槽内的销调整座垫倾斜 (6) 。 抓住椅盘并且沿向前-向上和-向后方向转动可达到较大角度位置,而向前-向下和-向后转动可达到较小角度位置。
腰部支撑调整
Show/hide table
图 3 | g02482316 |
(7) 摇臂支撑调整旋钮 |
逆时针转动旋钮 (7) 可提高腰部支撑。 顺时针转动旋钮 (7) 可降低腰部支撑。
扶手调整
Show/hide table
图 4 | g02482418 |
(8) 扶手调整圆筒 |
通过转动圆筒 (8) 可调整扶手角度。 不需要时,可以将扶手转到垂直位置。
肩带的调整
Show/hide table
图 5 | g02482139 |
(9) 座椅安全带调整杆 |
沿下面旋钮的方向向下按压立柱侧面上的操纵杆 (9) 。 调整肩带的高度。 在几个位置之一处松开操纵杆。
首选座椅控制
Show/hide table
图 6 | g02481436 |
(3) 加热/通风模式选择 (4) 加热/通风水平调整 |
要想使用加热/通风模式选择开关 (3) ,向右按此开关可启动冷却模式,而向左按可启动加热模式。
要想使用加热/通风水平开关 (4) ,向下按摇臂开关可获得低水平,而向上按此开关可获得高水平。 将摇臂开关按到中间可断开开关。
Caterpillar Information System:
541 Series 2 and 552 Series 2 Track Feller Bunchers Engine Supplement Engine - Remove and Install
541 Series 2 and 552 Series 2 Track Feller Bunchers Engine Supplement Machine Preheater - Remove and Install
541 Series 2 and 552 Series 2 Track Feller Bunchers Engine Supplement Refrigerant Compressor - Remove and Install
541 Series 2 and 552 Series 2 Track Feller Bunchers Engine Supplement Muffler - Remove and Install
PM-200 Cold Planer Machine Systems Track Roller - Assemble
PM-200 Cold Planer Machine Systems Track Roller - Disassemble
PM-200 Cold Planer Machine Systems Track Roller - Install
PM-200 Cold Planer Machine Systems Track Roller - Remove
AP1000E Asphalt Paver Equipped with a Cat C6.6 Engine Hydraulic System Oil Filters - Replace
541 Series 2 and 552 Series 2 Track Feller Bunchers Engine Supplement Starting Aid (Air Inlet Heater) - Remove and Install
541 Series 2 and 552 Series 2 Track Feller Bunchers Engine Supplement Turbocharger - Remove and Install
541 Series 2 and 552 Series 2 Track Feller Bunchers Engine Supplement Reversible Fan - Assemble
Contour Series Seat Troubleshooting Chart
541 Series 2 and 552 Series 2 Track Feller Bunchers Engine Supplement Hood Tilt Cylinder - Remove and Install
725C2 Articulated Truck Camera
541 Series 2 and 552 Series 2 Track Feller Bunchers Engine Supplement Hood Tilt Pump and Motor - Remove and Install
C4.4 Industrial Engine Fuel Filter Base - Single Secondary Fuel Filter Base
2011/04/01 A Troubleshooting Procedure Is Available for Implement Check and Relief Valve Group on Certain M and M Series 2 Motor Graders {4300, 5050}
2011/04/19 Updated Demand Fan Recalibration Information Available for Landfill Compactor, Wheel Dozer, and Wheel Loader Machines {1386, 1387}
SC-57 Felling Head Felling Head Piston Motor (Disc Saw)
924K, 930K and 938K Wheel Loaders Drive Shaft Spline - Lubricate - If Equipped
Field Installation of the 364-1356 Quick Coupler Conversion Kit (Hydraulic){6129} Field Installation of the 364-1356 Quick Coupler Conversion Kit (Hydraulic){6129}
2011/05/20 New Fuel Water Separator Bowls are Now Used on Certain Caterpillar Equipment {1261, 1263}
735B, 740B and 740B EJECTOR Articulated Trucks Engine Supplement Exhaust Elbow - Remove and Install