Flywheel - Remove - Equipped with Rear Power Take-Off
Show/hide table
Required Tools | |||
---|---|---|---|
Tool | Part Number | Part Description | Qty |
A | - | Guide Stud 1/2 inch - UNF by 4 inch |
2 |
Start By:
- Remove the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting Motor - Remove and Install" for the correct procedure.
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Remove bolts from Position (X) from flywheel (1).
- Install Tooling (A) in Position (X) to flywheel (1).
- Use a suitable lifting device to support the flywheel. The weight of flywheel (2) is approximately
55 kg (121 lb) . - Remove remaining bolts (2).
- Use the lifting device to remove flywheel (1) from the engine.
- Remove Tooling (A).
Show/hide table
Illustration 2 g02062054 - Inspect flywheel (1) and ring gear (3) for wear and damage. Replace any worn components or damaged components.
- To remove flywheel ring gear (3), follow Step 8.a through Step 8.b.
- Place the flywheel assembly on a suitable support.
- Use a hammer and a punch in order to remove ring gear (3) from flywheel (1).
Note: Identify the orientation of the teeth on the flywheel ring gear.
Show/hide table
Illustration 1 | g02062053 |
Caterpillar Information System:
C6.6 Industrial Engine Flywheel - Install - Equipped with Rear Power Take-Off
3516C and C175-16 Engines Selective Catalytic Reduction Component Location
UPS 1000Z, UPS 1200Z, UPS500G and UPS600G Uninterruptible Power Supplys Symbols
UPS 1000Z, UPS 1200Z, UPS500G and UPS600G Uninterruptible Power Supplys Acronyms
C15 Petroleum Engines Exhaust Manifold - Remove and Install
CT660 CX31 and CX31 HT On Highway Truck Power Train Electronic Control System Wiring Harness (Short Circuit) - Test
CT660 CX31 and CX31 HT On Highway Truck Power Train Electronic Control System Wiring Harness (Open Circuit) - Test
CT660 CX31 and CX31 HT On Highway Truck Power Train Electronic Control System Electrical Connector - Inspect
UPS 1000Z, UPS 1200Z, UPS500G and UPS600G Uninterruptible Power Supplys System Bypass Operation
Receiving and Unpacking of UPSB505{4480} Receiving and Unpacking of UPSB505{4480}
UPS 1000Z, UPS 1200Z, UPS500G and UPS600G Uninterruptible Power Supplys Receiving and Handling
2011/02/17 Improved Registration Process for Retrofit Products {1000, 3000, 7000, 7570}
C13, C15, and C18 Tier 4 Interim Engines Electrical Power Supply - Test
2011/05/16 Improved Software is Now Used for the TH48-E80 Petroleum Transmissions and the SPF343C Pumpers {7620}
2011/02/24 Procedure for Improving Battery Life on Generator Sets {1401}
Assembling and Installing a Selective Catalytic Reduction (SCR) Module for Certain 3516C Generator Sets{1050, 108D, 7279} Assembling and Installing a Selective Catalytic Reduction (SCR) Module for Certain 3516C Generator Sets{1050, 108D, 7279}
C15 Petroleum Engines Engine Oil Filter Base - Remove
C15 Petroleum Engines Engine Oil Filter Base - Install
C15 and C18 Industrial Engines Clean Emissions Module
C15 Petroleum Engines Engine Oil Cooler - Remove
CX31 and CX31 HT On-Highway Transmissions Retarder Operation
CX31 and CX31 HT On-Highway Transmissions Transmission Operation
CX31 On-Highway Transmission Lubricant Viscosities
CX31 and CX31 HT On-Highway Transmissions Capacities (Refill)