C6.6 Industrial Engine Caterpillar


Flywheel - Install - Equipped with Rear Power Take-Off

Usage:

C6.6 667

Installation Procedure

Table 1
Required Tools 
Tool  Part Number  Part Description  Qty 
Guide Stud
1/2 inch - UNF by 4 inch 


NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.




    Illustration 1g02062093

    ------ WARNING! ------

    Always wear protective gloves when handling parts that have been heated.


  1. If the flywheel ring gear was removed, follow Step 1.a through Step 1.c in order to install ring gear (3) to flywheel (1).

    1. Identify the orientation of teeth (4) on new ring gear (3).

      Note: The chamfered side of ring gear teeth (4) must face toward the starting motor when the flywheel is installed. The chamfered side of ring gear teeth ensures the correct engagement of the starting motor.

    2. Heat flywheel ring gear (3) in an oven to a maximum temperature of 250 °C (482 °F) prior to installation.

      Note: Do not use a torch to heat the ring gear.

    3. Ensure that the orientation of ring gear (3) is correct and quickly install the ring gear onto flywheel (1).

  2. Inspect the crankshaft rear seal for leaks. If there are any oil leaks, replace the crankshaft rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear Seal - Install" for the correct procedure.


    Illustration 2g02062053

  3. Install a suitable lifting device on flywheel (1). The flywheel can weigh 55 kg (121 lb).

  4. Install Tooling (A) in Position (X) on the crankshaft.

  5. Use the lifting device to position flywheel (1) onto Tooling (A).

  6. Install bolts (2) to flywheel (1).

  7. Remove Tooling (A) and install remaining bolts (2) to flywheel (1).

  8. Use a suitable tool to prevent the flywheel from rotating. Tighten bolts (2) and (4) to a torque of 140 N·m (103 lb ft).

  9. Remove the lifting device from flywheel (1).

  10. Check the run out of the flywheel. Refer to System Operation, Testing and Adjusting, "Flywheel" for more information.

End By:

  1. Install the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting Motor - Remove and Install" for the correct procedure.

Caterpillar Information System:

3516C and C175-16 Engines Selective Catalytic Reduction Component Location
UPS 1000Z, UPS 1200Z, UPS500G and UPS600G Uninterruptible Power Supplys Symbols
UPS 1000Z, UPS 1200Z, UPS500G and UPS600G Uninterruptible Power Supplys Acronyms
C15 Petroleum Engines Exhaust Manifold - Remove and Install
CT660 CX31 and CX31 HT On Highway Truck Power Train Electronic Control System Wiring Harness (Short Circuit) - Test
CT660 CX31 and CX31 HT On Highway Truck Power Train Electronic Control System Wiring Harness (Open Circuit) - Test
CT660 CX31 and CX31 HT On Highway Truck Power Train Electronic Control System Electrical Connector - Inspect
UPS 1000Z, UPS 1200Z, UPS500G and UPS600G Uninterruptible Power Supplys System Bypass Operation
Receiving and Unpacking of UPSB505{4480} Receiving and Unpacking of UPSB505{4480}
UPS 1000Z, UPS 1200Z, UPS500G and UPS600G Uninterruptible Power Supplys Receiving and Handling
2011/02/17 Improved Registration Process for Retrofit Products {1000, 3000, 7000, 7570}
UPS 1000Z, UPS 1200Z, UPS500G and UPS600G Uninterruptible Power Supplys Information Plate
C6.6 Industrial Engine Flywheel - Remove - Equipped with Rear Power Take-Off
C13, C15, and C18 Tier 4 Interim Engines Electrical Power Supply - Test
2011/05/16 Improved Software is Now Used for the TH48-E80 Petroleum Transmissions and the SPF343C Pumpers {7620}
2011/02/24 Procedure for Improving Battery Life on Generator Sets {1401}
Assembling and Installing a Selective Catalytic Reduction (SCR) Module for Certain 3516C Generator Sets{1050, 108D, 7279} Assembling and Installing a Selective Catalytic Reduction (SCR) Module for Certain 3516C Generator Sets{1050, 108D, 7279}
C15 Petroleum Engines Engine Oil Filter Base - Remove
C15 Petroleum Engines Engine Oil Filter Base - Install
C15 and C18 Industrial Engines Clean Emissions Module
C15 Petroleum Engines Engine Oil Cooler - Remove
CX31 and CX31 HT On-Highway Transmissions Retarder Operation
CX31 and CX31 HT On-Highway Transmissions Transmission Operation
CX31 On-Highway Transmission Lubricant Viscosities
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.