Equipment and Tools for Undercarriage Rebuilding and Reconditioning Stations {0729, 4150} Caterpillar

Equipment and Tools for Undercarriage Rebuilding and Reconditioning Stations {0729, 4150}

Usage:

D6D 01Y

Caterpillar Products: Machines with Grease Lubricated Track with Swage; Machines with Greased Lubricated Track (GLT); Machines with Positive Pin Retention (PPR) Track; Machines with Positive Pin Retention 2 (PPR2) Track; Machines with Rotating Bushing Track; Machines with Sealed Positive Pin Retention (PPR) Track; Machines with Sealed Track; Machines with Sleeve Bearing Track; Machines with SystemOne Undercarriage; Machines with non-PPR Sealed and Lubricated Track

Introduction

Show/hide table

Table 1
Revision	Summary of changes in SEBF8516
26	Added serial number prefixes for New Product Introduction.
25	Added 558GF, to tables. Added serial number prefixes for New Product Introduction.
24	Added serial number prefixes for New Product Introduction.
23	Added D5R2, 340F, 352F, 349F, 325F, 323F, and 538Bto tables. Added serial number prefixes for New Product Introduction.
22	Added D6R, to tables. Updated Introduction Information. Added serial number prefixes for New Product Introduction.
21	Added D6R2, 963K, PL72, PL83, PL87, 312F, 313F, 316F, 318F, and 320F to tables. Added serial number prefixes for New Product Introduction.

© 2019 Caterpillar All Rights Reserved. This guideline is for the use of Caterpillar dealers only. Unauthorized use of this document or the proprietary processes therein without permission may be violation of intellectual property law. Information contained in this document is considered Caterpillar: Confidential Yellow.

This Undercarriage Reconditioning Bulletin contains the necessary information to allow a dealer to establish a parts reusability program. Reuse and salvage information enables Caterpillar dealers and customers to benefit from cost reductions. Every effort has been made to provide the most current information that is known to Caterpillar. Continuing improvement and advancement of product design might have caused changes to your product which are not included in this publication. This Undercarriage Reconditioning Bulletin must be used with the latest technical information that is available from Caterpillar.

For questions when using this document, work with your Dealer Technical Communicator (TC).

To report suspected errors, inaccuracies, or suggestions regarding this document, submit a form for feedback in the Service Information System(SIS Web) interface.

Summary

to achieve optimum shop efficiency, each workstation should be equipped with all the necessary tools. The following examples should be considered basic tools. Extra tools may be required to fill individual dealer needs.

References

Reference: Catalog, NENG2500, "Dealer Service Tools Catalog"

Reference: Reference Manual, SEBF8599, "Undercarriage Reconditioning Guide"

Reference: Parts Sales Kit, PECP3003

Reference: Undercarriage Reconditioning Bulletin, SEBF8586, "Removal, Installation, and Conditioning of Idler Bearings and Track Roller Bearings"

Reference: Undercarriage Reconditioning Bulletin, SEBF8597, "Reconditioning Procedure for Seal Ramps on Inverted Style Idler and Roller Shafts."

Safety

Show/hide table




Illustration 1	g02139237

Most accidents that involve product operation, maintenance, and repair are caused by failure to observe basic safety rules or precautions. An accident can often be avoided by recognizing potentially hazardous situations before an accident occurs. A person must be alert to potential hazards. This person should also have the necessary training, skills, and tools to perform these functions properly.

This bulletin may contain hazardous steps. A safety alert symbol like the one below is used to indicate hazard.

Warning messages identify a specific, imminent, latent, hazard that has a reasonable probability of resulting in personal injury or death if the warning is ignored.

Show/hide table




Illustration 2	g03186216
Example warning

Show/hide table

Do not attempt to disassemble or assemble this machine until you read and understand the disassembly and assembly instructions. Improper disassembly and assembly procedures could result in injury or death.

Show/hide table

Inspect all threaded components before use. Damaged threads may fail under hydraulic pressure. Broken threads may release flying objects that are propelled with great force. Personal injury or death can occur if struck by flying objects.

Show/hide table

Do not stand near the hydraulic press while the press is in operation. A component that slips or breaks under pressure may fly into the air with great force. Personal injury or death can occur if struck by flying objects.

Canceled Part Numbers and Replaced Part Numbers

This document does not include all canceled part number and replaced part number information. Use NPR on SIS for information about canceled part numbers and replaced part numbers. NPR will provide the current part numbers for replaced parts.

Tooling and Equipment

Track Press Work Station

Show/hide table




Illustration 3	g02378776
Track press work station

In addition to a track press that has a minimum capacity of (300 tons), 2664 kN (600000.0 lb), the following tools are required.

Note: The track press in Illustration 3 has a maximum capacity of (375 tons), 3330 kN (750000.0 lb).

Show/hide table

Table 2
Required Tools
Part Number	Description
5P-3010	Deburring Tool
FT-1238	Vacuum Tank Assembly
5P-1725	Stopper Installation Tool
5P-7392	Stopper Installation Tool
6V-0136	Stopper Installation Tool
5P-7419	Installer Tool
1U-7593	Pry Bar
FT-1953	Indicator Gauge Gp
1U-9978	Acid Brush
222-3074	Die Grinder
--	1/2 inch Drill
1U-5617	Drill Bit
--	Contact tooling⁽¹⁾
--	Track shoe lifter⁽²⁾
--	Nut wrenches⁽³⁾
--	Track bolt sockets⁽³⁾
--	Conveyor (50 ft)⁽²⁾
--	Torque Turn Wrench⁽²⁾
170-5664	Test and Fill Cart Gp

Show/hide table

⁽¹⁾	Refer to Catalog, NENG2500, "Dealer Service Tools Catalog" for complete list.
⁽²⁾	Contact Dealer Service Tools Division for more information.
⁽³⁾	Refer to the "Torque Turn Wrench" section.

Non-Positive Pin Retention (PPR) Sealed and Lubricated Track

Show/hide table

Table 3
Seal Installers
Machine	Part Number
D4C, D3C	165-2571
D4E, 943	165-2573
D5K, D5C, D4H	4C-8615
D5M, D5N, D4HD	133-1532
D5	165-2571
D6K25, D6K, D6M, D6N, D5H, D5HD	4C-8616
D6D, 963, 963, 955	133-1533
D6R2, D6R, D6H, D6HD, D6T, D5R2, 527	4C-8617
D7G, 977, 973, 571, 572, PL72	133-1534
D7H, D7R, D7HD, PL83, PL87	4C-8619
D8K, 983	4C-8618
D8R, D8N, D8L, D8T, D7E, 578, 973D	4C-8619
D9H, D9G	4C-8620
D9L, D9N, D9R, D9T, 589	4C-8621
D10, D10N, D10R, D10T, 591	4C-8622
D11R, D11N, D11T	4C-8623

Show/hide table

Table 4
Bushing End Groove Gauge
Machine	Part Number
D4C, D3C	165-2572
D4E, 943	165-2574
D5K, D5C, D4H	4C-8602
D5M, D5N, D4HD	133-1535
D5	197-6569
D6K2, D6K, D6M, D6N, D5R2, D5H, D5HHD	133-1356
D6K2, D6K, D6M, D6N, D5R2, D5H, D5HHD	4C-8603
D6D, 963, 963K, 955	133-1537
D6R, D6R2, D6H, D6HD, D6T, 527	133-1538
D6R, D6R2, D6H, D6HD, D6T, 527	4C-8604
D7G, 977, 973, 571, 572, PL72	133-1539
D7H	4C-8605
D7R, D7HD, D7E, D8R, D8N, D8L, D8T, 578, 973D, PL83, PL87	133-1540
D7R, D7HD, D7E, D8R, D8N, D8L, D8T, 578, 973D, PL83, PL87	4C-8607
D8K, 983	4C-8608
D9H, D9G	4C-8608
D9L, D9N, D9R, D9T, 589	4C-8609
D9L, D9N, D9R, D9T, 589	4C-8610
D10, D10N, D10R, D10T, 591	4C-8611
D10, D10N, D10R, D10T, 591	4C-8612
D11R, D11N, D11T	4C-8613

PPR Tooling

Show/hide table




Illustration 4	g02378884
Track press using PPR tooling (1) Handle assembly (2) Unlocking tool anvil (3) Extruder assembly

Show/hide table




Illustration 5	g02378885
Track press using PPR unlocking tool (1) Handle assembly (2) Unlocking tool

Show/hide table

Table 5
PPR Track Press Tooling
Machine	Part Number	Description
All	8T-3216	Anvil Assembly
All	157-8547	Unlocking Tool
All	1U-6257	Stud
All	8T-3211	Handle As
D8N, D8R, D8T, D8B, 578	203-0982	Extruder Assembly
D9L, D9N, D9R, D9T, 589	198-5343	Extruder Assembly
D10, D10N, D10R, D10T, 591	198-5342	Extruder Assembly
D11N, D11R, D11T	198-5341	Extruder Assembly
--	9U-7829	Extruder Base⁽¹⁾

Show/hide table

⁽¹⁾	Only required for D11

Test and Fill machine

Show/hide table




Illustration 6	g02378777
Test and fill machine

Show/hide table

Table 6
170-5664 Test and Fill Cart Gp
Quantity	Part Number	Description
1	183-9303	Test Tube
1	216-2856	Test Tube
--	--	Nitrogen
--	--	Track Oil
1	8T-O831⁽¹⁾	Tip - Lubricator
1	4C-8855⁽¹⁾	3/8 inch Combo Regulator/Filter
1	4C-7272⁽¹⁾	1/2 inch Combo Regulator/Filter
1	4C-7273⁽¹⁾	3/4 inch Combo Regulator/Filter
1	9U-6038	Mounting Kit

Show/hide table

⁽¹⁾	Purchase the correct size combo unit for your facility

Torque Turn Wrench

Show/hide table




Illustration 7	g02378778
Torque turn wrench

Show/hide table

Table 7
Nut Wrenches
Part Number	Size
4C-8207	38.4 mm and 33.5 mm (1.51 inch and 1.32 inch)
4C-8208	32.3 mm and 30.2 mm (1.27 inch and 1.19 inch)
4C-8209	29.2 mm and 26.2 mm (1.15 inch and 1.03 inch)
4C-8210	25.4 mm and 22.6 mm (1.00 inch and 0.89 inch)
188-0956	32.0 mm and 42.0 mm (1.26 inch and 1.65 inch)
188-0959	25.0 mm and 30.0 mm (0.98 inch and 1.18 inch)

Show/hide table

Table 8
Impact Sockets
Size	Part Number	Description	Drive
19 mm	1U-7626	Tapered Socket	1 inch
3/4 inch	214-6553	Thin Wall Socket	3/4 inch
27/32 inch	6V-4175	Thin Wall Socket	1 inch
22 mm	1U-7627	Tapered Socket	1 inch
7/8 inch	214-6556	Thin Wall Socket	3/4 inch
7/8 inch	9S-6375	Thin Wall Socket	1 inch
29/32 inch	6V-7928	Thin Wall Socket	1 inch
29/32 inch	6V-2002	Standard Socket	1 inch
15/16 inch	214-6557	Thin Wall Socket	3/4 inch
15/16 inch	9S-6374	Thin Wall Socket	1 inch
15/16 inch	9S-6370	Standard Socket	1 inch
24 mm	1U-7628	Tapered Socket	1 inch
1 1/16 inch	214-6559	Thin Wall Socket	3/4 inch
27 mm	1U-7629	Tapered Socket	1 inch
1 3/32 inch	5P-3579	Standard Socket	1 inch
1 1/8 inch	9S-6369	Thin Wall Socket	1 inch
1 1/8 inch	9S-6373	Standard Socket	1 inch
30 mm	1U-7630	Tapered Socket	1 inch
1 3/16 inch	214-6561	Thin Wall Socket	3/4 inch
1 1/4 inch	214-6562	Thin Wall Socket	3/4 inch
32 mm	1U-7631	Tapered Socket	1 inch
1 9/32 inch	5P-3580	Standard Socket	1 inch
1 5/16 inch	9S-6372	Standard Socket	1 inch
1 15/32 inch	5P-3581	Standard Socket	1 inch
1 1/2 inch	9S-6371	Standard Socket	1 inch
1 5/8 inch	1U-8798	Tapered Socket	1 1/2 inch
1 11/16 inch	1U-8586	Tapered Socket	1 1/2 inch
2 inch	8T-9175	Standard Socket	1 1/2 inch
2 1/16 inch	8T-9174	Standard Socket	1 1/2 inch

Idler/Roller Welding Equipment

Show/hide table




Illustration 8	g02378779
Idler/Roller welder work station

Show/hide table

Table 9
Required Tools
Part Number	Description
--	Idler/Roller welder
6V-6193	Diagonal Cutter
4S-9405	Caliper (12 inch)
5P-3920	Rule (12 inch)
6V-9410	Gauge Group
1U-9915	Wire Brush
--	Weld chipping hammer
--	Air Scaler
349-4200	Infrared Thermometer
311-2056	Cutting Torch - Oxyacetylene
FT-1412	Wear Gauge
FT-1431	Fabricated Roller Rack
FT-1738	3/4-16 Stud
6V-7935	Screwdriver
8H-8577	Hammer
223-1154	Pneumatic Scribing Tool
1P-3036	Tap
1P-3048	Tap Wrench
5M-2080	Lubricator Nozzle
5P-1720	Seal Pick
222-3050	1/2 inch Impact Wrench
2P-8312	Retaining Ring Pliers
7H-1680	Lubrication Hand Pump

Show/hide table

Table 10
Additional Tooling for Water-Cooled Work Stations
Part Number	Description
261-0444	Plug Socket
6V-6140	Cooling Adapter
6V-6163	Cooling Adapter
1U-5530	Cooling Adapter
5V-8610	Quick Disconnect - (Female)
5V-8611	Quick Disconnect - (Male)
213-6930	14 mm Impact Socket
5P-6587	Lock Removal Socket
5P-6588	Lock Removal Socket
5P-6589	Lock Removal Socket
8H-8582	Vise Grip
1F-1161	Cold Chisel
8T-0447	Dial Caliper As
5P-7419	Installer Tool
369-9451	Grease-Petro Gel
136-1452	Retaining Ring Pliers As
2P-8312	Retaining Ring Pliers
FT-0578	Bushing Alignment Tool
170-5664	Test and Fill Cart Gp
222-3050	1/2 inch Impact Wrench
FT1535	Idler Bearing Puller
223-1154	Pneumatic Scribing Tool

Bearing Cup Removal Tooling

The following tools are necessary to service the carrier rollers. Proper removal and installation of bearings, races, and seals can be accomplished quickly and easily with these driver tools.

Show/hide table

Table 11
Tools Required
Part Number	Description
1P-0510	Bearing and Seal Driver Group
1P-0520	Bearing and Seal Driver Group

Some of the tools require modification before use. The necessary modification dimensions are given in the following illustrations.

Show/hide table




Illustration 9	g02378780
Dimension to modify the 1P-0494 Drive Plate (A) 57.2 mm (2.25 inch) (B) 15.8 mm (0.62 inch) (C) 35.1 mm (1.38 inch)

Show/hide table




Illustration 10	g02378781
Dimensions to modify the 1P-0487 Drive Plate (B) 15.8 mm (0.62 inch) (D) 50.8 mm (2.00 inch) (E) 57.2 mm (2.25 inch)

Show/hide table




Illustration 11	g02378782
Dimensions to modify the 1P-0493 Drive Plate, 1P-0508 Drive Plate, and 1P-0513 Drive Plate. (F) 19 mm (0.75 inch)

Bearing Cup Installation Tooling

Show/hide table




Illustration 12	g02378783
Typical bearing cap installation tools

Blast Cabinet

Show/hide table




Illustration 13	g02378784
Blast cabinet

The blast cabinet is utilized when conditioning the shafts for the idlers with inverted Duo-Cone seals. For more information, refer to Undercarriage Reconditioning Bulletin, SEBF8597, "Reconditioning Procedure for Seal Ramps on Inverted Style Idler and Roller Shafts.".

Roll Burnish

Show/hide table




Illustration 14	g02378785
Roll burnish tooling for conditioning the bearing idler

The roll burnishing procedure is used when conditioning either the idler or the roller bearings. The conditioning of the bearings is necessary for the correct alignment of the shaft and the correct size and surface finish that is required. For more information, refer to Undercarriage Reconditioning Bulletin, SEBF8586, "Removal, Installation, and Conditioning of Idler Bearings and Track Roller Bearings".

Show/hide table

Table 12
Roll-Burnish Process Hardware
ELLIOTT Ref. No.	Item
--	Radial Drill
5613-201-11410	D11 Burnish tool ( 162.82 mm (6.410 inch) dia.)
5612-201-11344	D10 Burnish tool ( 136.78 mm (5.385 inch) dia.)
5611-201-11320	D9 Burnish Tool ( 127.25 mm (5.010 inch) dia.)
5611-201-11272	D7/ D8 Burnish tool ( 108.05 mm (4.254 inch) dia.)
5408-211-11160	D5/ D6 Burnish tool ( 63.75 mm (2.510 inch) dia.)

Hone

Show/hide table




Illustration 15	g02378786
Honing tooling

The honing procedure is used when conditioning either the idler or the roller bearings. The conditioning of the bearings is necessary for the correct alignment of the shaft and the correct size and surface finish that is required. For more information, refer to Undercarriage Reconditioning Bulletin, SEBF8586, "Removal, Installation, and Conditioning of Idler Bearings and Track Roller Bearings".

Show/hide table

Table 13
Hone Process Hardware
Part Number	Description
9U-5797	Drill
FT-2683	Universal Pilot
6V-6094	Hone Body
177-9708	Stone Set (D5- D10)
177-9709	Stone Set (D11)
5P-8591	Holder

Roller Press Work Station

Show/hide table




Illustration 16	g02378787
264-0054 Roller Assembly Machine

In addition to a roller assembly machine that has a minimum capacity of 445 kN (100040 lb), the following tools are required.

Show/hide table

Table 14
Required Tools
Part Number	Description
6V-0092	Plug Socket
6V-7935	Screwdriver
8H-8577	Hammer
214-6501	1/2 inch Impact Socket
214-6503	9/16 inch Impact Socket
214-6507	3/4 inch Impact Socket

Roller Bushing Installation Tooling

Used to install bushings into track roller (provides correct and consistent installation depth.)

Show/hide table

Table 15
Machine	Part Number
D5M, D5C, D4H	126-4045, 166-5902⁽¹⁾
D6M, D6N, D5H, 953	123-6692
D6R, D6R2, D6H, 963, 963K	123-6693
D7R, D7H, 973, PL72, PL83, PL87	123-6699

Show/hide table

⁽¹⁾	Use on certain machines that need shallower set points.

Duo-Cone Seal Installation Tooling

Idlers with Inverted Duo-Cone Seals

Show/hide table

Table 16
Duo-Cone Seal Installation Tooling
Machine	Part Number	Description
D4H	8T-0945	Alignment Sleeve
	8T-0943	Retainer Seal Installer
	8T-0943	Shaft Seal Installer
	FT-1994	Spin Socket
D5H	8T-0945	Alignment Sleeve
	8T-0941	Retainer Seal Installer
	8T-0941	Shaft Seal Installer
	FT-1994	Spin Socket
D5M D6M	179-7208	Seal Installer Assembly
D6H D6R D7H	8T-0822	Alignment Sleeve
	8T-0939	Retainer Seal Installer
	8T-0939	Shaft Seal Installer
	FT-1911	Spin Socket
D8L D8N	8T-0823	Alignment Sleeve
	8T-0829	Retainer Seal Installer
	8T-0829	Shaft Seal Installer
	FT-1910	Spin Socket
D9L	8T-0824	Alignment Sleeve
	8T-0830	Seal Installer
	8T-0830	Seal Installer
	1U-9398	Socket As
D9N	8T-0823	Alignment Sleeve
	8T-7640	Retainer Seal Installer
	8T-7640	Shaft Seal Installer
	FT-1910	Spin Socket
D10	8T-0825	Alignment Sleeve
	8T-0826	Retainer Seal Installer
	8T-0826	Shaft Seal Installer
	1U-9399	Shaft Socket As
D10N	8T-0824	Alignment Sleeve
	8T-0830	Retainer Seal Installer
	8T-0830	Shaft Seal Installer
	FT-1909	Spin Socket
D11N	8T-0825	Alignment Sleeve
	8T-7639	Retainer Seal Installer
	8T-7639	Shaft Seal Installer
	1U-9399	Shaft Socket As

Rollers with Inverted Duo-Cone Seals

Show/hide table

Table 17
Duo-Cone Seal Installation Tooling
Machine	Part Number	Description
D4H D5H	8T-0945	Alignment Sleeve
	8T-0942	Retainer Seal Installer
	8T-0942	Shaft Seal Installer
	FT-1994	Spin Socket
D6H D7H	8T-0822	Alignment Sleeve
	8T-0939	Retainer Seal Installer
	8T-0939	Shaft Seal Installer
	FT-1911	Spin Socket
D8L D8N	8T-0822	Alignment Sleeve
	8T-0828	Retainer Seal Installer
	8T-0828	Shaft Seal Installer
	FT-1911	Spin Socket
D9L	8T-0823	Alignment Sleeve
	8T-0829	Retainer Seal Installer
	8T-0829	Shaft Seal Installer
	FT-1910	Spin Socket
D9N	8T-0822	Alignment Sleeve
	8T-7641	Retainer Seal Installer
	8T-7641	Shaft Seal Installer
	FT-1911	Spin Socket
D10	8T-0824	Alignment Sleeve
	8T-0827	Retainer Seal Installer
	8T-0827	Shaft Seal Installer
	1U-9398	Socket As
D10N	8T-0823	Alignment Sleeve
	8T-0829	Retainer Seal Installer
	8T-0829	Shaft Seal Installer
	FT-1910	Spin Socket
D11N	8T-0824	Alignment Sleeve
	8T-0827	Retainer Seal Installer
	8T-0827	Shaft Seal Installer
	1U-9398	Socket As
943 953	8T-0945	Alignment Sleeve
	8T-0942	Retainer Seal Installer
	8T-0942	Shaft Seal Installer
	FT-1994	Spin Socket
963	8T-0822	Alignment Sleeve
	8T-0940	Retainer Seal Installer
	8T-0940	Shaft Seal Installer
	FT-1911	Spin Socket
973	8T-0822	Alignment Sleeve
	8T-0939	Retainer Seal Installer
	8T-0939	Shaft Seal Installer
	FT-1911	Spin Socket

Idlers with Conventional Duo-Cone Seals

Show/hide table

Table 18
Duo-Cone Seal Installation Tooling
Machine	Part Number	Description
561	179-7208	Seal Installer
	201-1582	End Collar Tooling
	FT-1994	Spin Socket
527 572 PL72	136-6813	Seal Installer
	170-5412	End Collar Tooling
	FT-1911	Spin Socket
578 583R 583T 583X 587R 587T	227-4755	Duo-Cone Seal Installer As
	170-5408	End Collar Tooling
	FT-1910	Socket As
D4H D5M D5N	179-7208	Seal Installer
	201-1582	End Collar Tooling
	FT-1994	Spin Socket
D5H D6M D6N	179-7208	Seal Installer
	201-1581	End Collar Tooling
	FT-1994	Spin Socket
D5R2 D6K2 D6K D6H D6R D6R2 D6T	136-6813	Seal Installer
	170-5412	End Collar Tooling
	FT-1911	Spin Socket
D7E D7H D7R PL83 PL87	136-6813	Seal Installer
	170-5411	End Collar Tooling
	FT-1911	Spin Socket
D8L D8N D8R D8T	227-4755	Duo-Cone Seal Installer As
	170-5408	End Collar Tooling
	1U-9398 FT-1910	Spin Socket
D9N D9R D9T	137-9443	Duo-Cone Seal Installer As
	170-5409	End Collar Tooling
	1U-9398 FT-1910	Socket As
D9L	129-1340	Seal Installer
	170-5406	End Collar Tooling
	1U-9399, FT-1909	Spin Socket
D10N D10R D10T	129-1340	Seal Installer
	170-5406	End Collar Tooling
	1U-9399 FT-1909	Spin Socket
D11N D11R D11T	159-9843	Seal Installer
	170-5405	End Collar Tooling
	1U-9399	Spin Socket

Rollers with Conventional Duo-Cone Seals

Show/hide table

Table 19
Duo-Cone Seal Installation Tooling
Machine	Part Number	Description
578 583R 583T 583X 587R 587T D8L D8N D8R D8T	136-6813	Seal Installer
	170-5407	End Collar Tooling
	FT-1911	Spin Socket
D9L	137-9443	Duo-Cone Seal Installer As
	170-5408	End Collar Tooling
	FT-1910	Spin Socket
D9N D9R D9T	136-6813	Seal Installer
	170-5410	End Collar Tooling
	FT-1911	Spin Socket
D10N D10R D10T	137-9443	Duo-Cone Seal Installer As
	170-5408	End Collar Tooling
	FT-1910	Spin Socket
D11N D11R D11T	129-1340	Seal Installer
	170-5404	End Collar Tooling
	1U-9399	Shaft Socket As

Snap Ring Rollers

Show/hide table

Table 20
Duo-Cone Seal Installation Tooling
Machine	Part Number
D7R D7H D6R D6H 983 973D 973C 973 963C 963B 963 572R 527	1U-8840






D6M D5K D5G D5C D5M D5H D4H 953C 953B 953 943B 943 939C 939 561M 561h 517	1U-8843







D3K D4K	1U-8850

Oval Track Rollers

Show/hide table

Table 21
Duo-Cone Seal Installation Tooling
Machine	Part Number
D6R D6R2 D6M D6N D6K D6H D6D D6C D5M D5H D5B D5 D4H D4D D3 963 963K 961 955K 955L 955 953 951C 951B 951 943 941B 941 939 931 561M 561C 527 235 225 219 215SA 215B 215	1U-8843


















D9H D9G 594H 594	1U-8842
D9H D9G 594H 594	1U-8842
D8K D8H 583K 583H	1U-8841
D8K D8H 583K 583H	1U-8841
D7R D7H D7G D7F D7E D6R D6D D6C 983B 983 977L 977K 977 973 PL72 PL83 PL87 572 245 235	1U-8840







D96R D6M D6H D6D D6C D5M D5H D5B D5	1U-8843
D96R D6M D6H D6D D6C D5M D5H D5B D5	1U-8843

Excavator Track Rollers

Show/hide table

Table 22
Duo-Cone Seal Installation
Sales Model	Seal Installer
307 307B 307C 307D 308C 308D 308E	123-3800
311 311B 311C 311D 311F 312 312B 312C 312D 312D2 312F 313B 313C 313F 314C 314D 314E 314F	1U-6145
313D2 315 315B 315C 315D 315F MD5150 316E 316F 317 317B 318B 318C 318D 318D2 318E 318F 319C 319D 320⁽¹⁾ 320B⁽¹⁾ 320C⁽¹⁾ 320D 320E 320F 321C 321D 323D⁽¹⁾	1U-8841
318D2 318E 320⁽²⁾ 320B⁽²⁾ 320C⁽²⁾ 320D2⁽²⁾ 323D2⁽²⁾ 323D⁽³⁾ 323F 322 322B 322C 324D 325 325B 325C 325D 325F 326D 329D 538B 558GF	1U-8842
328D 330 330B 330C 330D 336D 336D2 336E 340D 340D2 340F 349F 352F 521B 522D	9U-7537
345 345B 345C 345D 350 568	1U-8849
365B 365C 374D 374F 375 5080 385B 385C 390D 390F 5090	4C-6206
5110B	1U-6339
5130 5130B	1U-6438

Show/hide table

⁽¹⁾	9W-2142 Duo-Cone Seal Gp and 206-9211 Duo-Cone Seal Gp
⁽²⁾	9W-2201 Duo-Cone Seal Gp
⁽³⁾	206-9212 Duo-Cone Seal Gp

Excavator Idlers

Show/hide table

Table 23
Duo-Cone Seal Installation
Sales Model	Seal Installer
307 307B 307C 307D 308C 308D 308E	123-3801
311 311B 311C 311D 311F 312 312B 312C 312D 312D2 312F 313B 313C 313F 314C 314D 314E	1U-8850
313D2 315 315B 315C 315D 315F MD5150 316E 316F 317 317B 318B 318C 318D 318D2 318E 318 ED 318F 319C 319D 320⁽¹⁾ 320B⁽¹⁾ 320C⁽¹⁾ 320D 320D2⁽¹⁾ 320E 320F 321C 321D 323D⁽¹⁾ 323D2⁽¹⁾ 323F	1U-8842
320⁽²⁾ 320B⁽²⁾ 320C⁽²⁾ 323D⁽²⁾ 322 322B 322C 324D 326D 325 325B 325C 325D 325F 329D MD6240 MD6290 538B 558GF	9U-7537
328D 330 330B 330C⁽³⁾ 330D⁽³⁾ 336D 336D2 336E 340D 340D2 340F 521B 522B MD5150C MD6420 MD6420B MD6420C	1U-8849
330C⁽⁴⁾ 330D⁽⁴⁾ 345B 345C 345D 349F 352F 350 568 MD6540 MD6540C MD6690	4C-6206
365B 365C 374D 374F 375 385B 385C 390D 390F	9U-7538
5110B	1U-6436
MD6240 MD6290	1U-8849
MD6420 MD6420B MD6420C	4C-6202
MD6540 MD6540C MD6640	9U-7538

Show/hide table

⁽¹⁾	9W-2201 Duo-Cone Seal Gp
⁽²⁾	109-0885 Duo-Cone Seal Gp
⁽³⁾	109-0881 Duo-Cone Seal Gp
⁽⁴⁾	109-0868 Duo-Cone Seal Gp

Excavator Carrier Rollers

Show/hide table

Table 24
Duo-Cone Seal Installation
Model No.	Seal Installer
308BSR 308CCR 308CSR 308DSR 308DCR 307C 307D 306 305.5 308B 308C 308D 307 307B	123-2999
311 311B 311C 311D 311F	1U-6144
312 312B 312C 312D 312F 313F 312D2	1U-6144
312 312B 312C 312D 312F 313F 312D2	9U-5985
313B 313C 313D2 314C 314D 314E 314F	1U-6144
315 315B 315C 315D 315F MD5150 316E 316F 317 317BL 317BLN 317N 318B 318BL 318BN 318C 318D 318D2 318E 318F	9U-5985
319D 319C	9U-5985
320S	224-9466
320S	1U-8843
313D2 320B 320C 320D 320D2 320E 320F	9U-5985
	224-9466
	1U-8843
320	9U-5985
320	1U-6144
321BSR 321D 321C 322 322B 322C 323D 323D2 323F 324D 326D 538B	9U-5985
325 325B 325C 325D 325F 558GF	224-9466
325 325B 325C 325D 325F 558GF	1U-8843
328D	9U-5985
328D	1U-8843
329D	1U-8843
330B 330C 330D 521B 522B	224-9466
	9U-5985
	1U-8843
330	224-9466
	1U-8843
	9U-5985
340F 340D2 340D 336F 336E 336D2 336D 330 330B 330C 330D 328D 325 325B 325C 325D 329D 558GF	1U-8843
	9U-7537
5110B	1U-6436
MD6240 MD6290	1U-8849
MD6420 MD6420B MD6420C	4C-6202
MD6540 MD6540C MD6640	9U-7538
5110B	1U-6436
MD6240 MD6290	1U-8849
MD6420 MD6420B MD6420C	4C-6202
MD6540 MD6540C MD6640	9U-7538
5110B	1U-6436
MD6240 MD6290	1U-8849
MD6420 MD6420B MD6420C	4C-6202
MD6540 MD6540C MD6640	9U-7538
345B 345BL 345C 345D 349F 352F 568 MD5075 MD5075C MD5150C MD5170	1U-8842
350	224-9466
	1U-8843
	1U-8842
365 365B 365C	1U-8843
365 365B 365C	1U-8842
374D 374F 375 385CL 385CFS 385C 385BL 385B 390D 390F	1U-8842