Fuel Priming Pump and Primary Fuel Filter - With Water Separator
Show/hide table
图 1 | g02539496 |
(C) 长度为 |
Show/hide table
360-1693 燃油注油泵和粗滤器总成的技术规格 | |||
项目 | 数量 | 零件 | 技术规格说明 |
1 | 1 | 9S-8002 O 形密封圈塞 | 拧紧至扭矩为 |
2 | 2 | 179-7267 塞 | 拧紧至扭矩为 |
3 | 1 | 211-2093 螺母 | 拧紧至扭矩为 |
4 | 1 | 300-3556 电磁阀总成 | 拧紧至扭矩为 工作电压为 24 VDC。 温度为 |
5 | 1 | 328-8351 接头 | 拧紧至扭矩为 |
6 | 1 | 327-8044 单向阀总成 | 拧紧至扭矩为 |
7 | 1 | 212-9580 油水分离器和燃油滤清器总成 | 拧紧油水分离器和燃油滤清器总成,直至它们正确落座在燃油注油泵总成中。 再拧紧 3/4 圈。 |
8 | 1 | 343-5527 油杯 | 拧紧至扭矩为 |
9 | 1 | 9S-4167 空心螺柱 | 将红色 Loctite 271 涂覆到长度 (C) 上,如图 1 中所示
拧紧至扭矩为 |
Caterpillar Information System:
349E, 349F and 352F Excavators and 349E MHPU Mobile Hydraulic Power Unit Tool Control System Medium Pressure: Relief Valve (Line) - Test and Adjust
349E, 349F and 352F Excavators and 349E MHPU Mobile Hydraulic Power Unit Tool Control System Medium Pressure: Relief Valve (Main) - Test and Adjust
2010/10/20 A New Rocker Shaft Bolt Is Used on Certain C15 and C18 Engines {1102, 7553}
G3520E Generator Set Engines Configuration Parameters
C13, C15, and C18 Tier 4 Final Engines Fuel Pressure Regulator
349E, 349F and 352F Excavators and 349E MHPU Mobile Hydraulic Power Unit Tool Control System One-Way/One or Two Pump - Electric Control: Relief Valve (Line) - Test and Adjust - Tool Relief Valve
C6.6 Industrial Engine Fuel Manifold (Rail)
C7.1 Industrial Engine Starting the Engine
C9.3 Tier 4 Final Engines Electric Starting Motor
C7.1 Industrial Engine Diesel Particulate Filter
C7.1 Industrial Engine Diesel Particulate Filter Temperature and Pressure Sensor
C6.6 Industrial Engine Fuel Transfer Pump - Electric Transfer Pump
349E, 349F and 352F Excavators and 349E MHPU Mobile Hydraulic Power Unit Tool Control System System Identification
349E, 349F and 352F Excavators and 349E MHPU Mobile Hydraulic Power Unit Tool Control System Work Tool - Select
349F and 352F Excavators Hydraulic System Work Tool Parameter - Program
C15 and C18 Engines Safety Messages
2010/11/29 Retrofitting for Ultra Lean Burn on a G3516 Engine {1000, 775E}
C27 and C32 Industrial Engines Engine Oil Filter Base - Remove and Install
2010/11/30 A New Muffler Assembly Prevents Exhaust Gas Recirculation on Certain 345D Excavators and Mobile Hydraulic Power Units {1062}
349E, 349F and 352F Excavators and 349E MHPU Mobile Hydraulic Power Unit Tool Control System Process for Setting Up the Work Tool
3516C Locomotive Engines Exhaust Manifold - Remove and Install
C15 and C18 Engines Belts - Inspect/Replace - If Equipped
349E, 349F and 352F Excavators and 349E MHPU Mobile Hydraulic Power Unit Tool Control System Combined Function - Electric Control: Parameter Setting
349E, 349F and 352F Excavators and 349E MHPU Mobile Hydraulic Power Unit Tool Control System Combined Function - Electric Control: Parameter Adjustment