Air Inlet Elbow - Remove and Install
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 369-9451 | Grease | 1 |
B | 6V-3009 | Crossbar | 1 |
6V-4832 | Forcing Screw | 1 | |
8B-7560 | Step Plate | 1 | |
126-7181 | Sliding Plate | 2 | |
1U-6342 | Threaded Rod M10 by 1.5 Thread | 1 | |
8T-4133 | Nut | 2 |
Start By:
- If necessary, remove the catalyst (module).
- Disconnect tube assembly (1).
- Remove stud bolt (2) and position the tube assembly out of the way.
Show/hide table
Illustration 2 g02245498 - Remove four bolts (3).
- Remove manifold (4) as an assembly.
Show/hide table
Illustration 3 g02291533 - Remove bolts (7) and separate mixing tube (8) from plate (6).
- Remove bolts (9) and separate mixing tube (8) from air inlet manifold (5). Remove and discard the O-ring seals.
Show/hide table
Illustration 4 g02291578 View from rear of the engine. - Remove bolt (11) from elbow (13).
- Remove stud bolt (10) from elbow (13).
- Remove eight bolts (12) and remove elbows (13).
Show/hide table
Illustration 1 | g02245414 |
View from the front of the engine. |
- Install manifold (4) in the reverse order of removal.
- Apply Tooling (A) to the O-ring Seals for elbows (13).
Show/hide table
Illustration 5 g02733037 - Position Tooling (B) and a suitable block of wood on the engine. Use Tooling (B) to install mixing tube (8) and install bolts (3).
- Apply Tooling (A) to the O-ring Seals for elbows (13).
Caterpillar Information System:
312F and 313F Excavators Fumes Disposal Filter Element - Replace
Replacing the High Pressure Fuel Pump on Certain C7 and C9 Engines{1251, 1714} Replacing the High Pressure Fuel Pump on Certain C7 and C9 Engines{1251, 1714}
C3.4B Engines Engine Has Early Wear
320E and 323E Excavators Fuel System Primary Filter (Water Separator) Element - Replace
C27 and C32 Industrial Engines Exhaust Gas Valve (NRS) - Remove and Install
312F and 313F Excavators Engine Oil Level - Check
Retrofitting for Ultra Lean Burn (ULB) on Certain G3516 Engines{1000, 775E} Retrofitting for Ultra Lean Burn (ULB) on Certain G3516 Engines{1000, 775E}
793F and 797F Off-Highway Trucks Chassis Electronic Control System Backlight Is On Continuously
120 and 120 AWD Motor Grader Braking System - Test
C3.4B Engines Diesel Particulate Filter Temperature Is Low
UPSB125 Uninterruptible Power Supply UPS Battery - 50Hz Advanced Preventive Maintenance
UPSB125 Uninterruptible Power Supply UPS Battery - 50Hz Basic Preventive Maintenance
C3.4B Engines Engine Overspeeds
C27 and C32 Engines for Caterpillar Built Machines Engine Oil Pressure Sensor - Remove and Install
3516C Locomotive Engines Selective Catalytic Reduction Module - Assemble
XQ Auto Paralleling Engine Stopping
XQ Auto Paralleling Fire Prevention and Explosion Prevention
XQ Auto Paralleling Engine Starting
XQ Auto Paralleling General Hazard Information
XQ Auto Paralleling Burn Prevention
XQ Auto Paralleling Before Starting Engine
349E, 349F and 352F Excavators and 349E MHPU Mobile Hydraulic Power Unit Tool Control System General Information
Instructions for Weld Finish of the "K" Series Adapters Installed on Large Wheel Loader Buckets{0679, 6101, 6102, 6104, 6805} Instructions for Weld Finish of the "K" Series Adapters Installed on Large Wheel Loader Buckets{0679, 6101, 6102, 6104, 6805}
C3.4B Engines Fuel Rail Pressure Problem