MID 113 - CID 0168 - FMI 03
产生此代码的情况:
Show/hide table
图 1 | g03326533 |
CID 0168 诊断代码与充油系统电压传感器有关。 当 ECM 读取到系统电压低于 32.5 DCV 时,会记录 FMI 03 诊断代码。 如果长时间保持高电压,则可能损坏电磁阀。
可能由于下列原因产生该诊断代码:
- 充电系统部件出故障。
- 线束导线有故障。
- ECM 出现故障。 这种情况不太可能。
注: 如果所有机器控制模块均激活 CID 0168 FMI 03 诊断代码,则系统电压可能故障。 系统电压由发动机交流发电机提供。 如果动力传动系 ECM 激活诊断代码,则机器线束可能故障,或一个接头对 ECM 闭路。 继续执行以下测试步骤,以隔离故障起因。
测试步骤 1. 检查 ECM 的系统电压
- 将钥匙起动开关转到断开位置。
- 在动力传动系 ECM 的线束接头 J1 上,用 7X-1710 万用表表笔 测量电源电压。 将正极表笔沿一条正极电源电路导线插到触点 J1-30(导线 140-RD)上。 将负极表笔沿一条电源回路导线插到触点 J1-13(导线 202-BK)上。
- 起动发动机并以低怠速运转发动机。
- 测量触点 J1-30 和触点 J1-13 之间的电压。
预期结果:
电压测量值在 18.0 VDC 到 32.0 VDC 的范围内。
结果:
- 正常 - 动力传动系 ECM 电源的电压测量值在 18.0 VDC 到 32.0 VDC 的范围内。 系统电压正常。 发动机交流发电机或机器电源电路应该没有故障。 转至测试步骤 2。
- 异常 - 动力传动系 ECM 电源的电压测量值大于 32.0 VDC。
修复: 发动机交流发电机的工作正常。 有关交流发电机的更多测试和修理步骤或发动机交流发电机的更改,请参阅专门说明书, REHS0354。
停止
测试步骤 2. 检查该诊断代码的状态
- 将钥匙起动开关转到接通位置。
- 起动发动机。 以低怠速运转发动机。
- 确定动力传动系 ECM 是否再次激活 CID 0168 FMI 03 诊断代码。
预期结果:
CID CID 0168 FMI 03 诊断代码为非激活状态
结果:
- 正常 - CID 0168 FMI 03 诊断代码为非激活状态。 此时不存在该诊断代码。 初始诊断代码可能由循环动力传动系 ECM 电源即已排除的瞬时状况引起。
修复: 使机器恢复正常运转。
停止
- 异常 - CID 0168 FMI 03 诊断代码为激活状态。
修复: 为动力传动系 ECM 闪存最新版本的软件。如果闪存最新软件后诊 FMI 03 诊断代码仍处于激活状态,请联系您代理商的技术通信员征求 Caterpillar 可能的意见。如果必须更换 ECM,请参阅测试与调整, "电子控制模块(ECM)- 更换"。
停止
Caterpillar Information System:
D11T Track-Type Tractor MID 113 - CID 0070 - FMI 04
NEHS1032: 538-5051 Communications Adapter 3 {0599, 0709, 1900, 4800, 7490, 7600} NEHS1032: 538-5051 Communications Adapter 3 {0599, 0709, 1900, 4800, 7490, 7600}
D11T Track-Type Tractor MID 113 - CID 0070 - FMI 03
D11T Track-Type Tractor MID 113 - CID 0041 - FMI 04
D8R and D8T Track-Type Tractors Engine Supplement Hydraulic Oil Cooler - Remove and Install
D11T Track-Type Tractor MID 113 - CID 0041 - FMI 03
D8T Track-Type Tractor Engine Supplement Power Train Oil Cooler - Remove and Install
D7E Track-Type Tractor Engine Supplement Fuel Transfer Pump - Remove and Install
Installation of 361-6832 High Intensity Discharge (HID) Lighting Kit {1429, 1434, 1434} Installation of 361-6832 High Intensity Discharge (HID) Lighting Kit {1429, 1434, 1434}
C6.6 Engines For Caterpillar Built Machines CID 0168 FMI 04
C6.6 Engines For Caterpillar Built Machines CID 0168 FMI 03
C7.1 Industrial Engine Fuel Temperature Sensor - Remove and Install
Caterpillar Monitoring System Service Tools
C4.2 and C6.4 Engines for Caterpillar Built Machines Air in Fuel - Test
D11T Track-Type Tractor MID 113 - CID 0168 - FMI 04
D11T, D8T and D9T Track-Type Tractors VIMSTM 3G / Product Link System Schematic
D7E Track-Type Tractor Engine Supplement Engine Electronic Control - Remove and Install
Installation Instructions for 361-6833 Lighting Group Warning Beacon Kit {1431, 1431} Installation Instructions for 361-6833 Lighting Group Warning Beacon Kit {1431, 1431}
Preventing Cracks and Leaks in the Composite Valve Covers on Some C9 Engines{1107, 1120} Preventing Cracks and Leaks in the Composite Valve Covers on Some C9 Engines{1107, 1120}
966K XE Wheel Loader C9.3 Engine Supplement Engine Oil Filter, Oil Filter Base and Oil Cooler - Remove and Install
D7E Track-Type Tractor Hydraulic, HVAC and Electrical Systems Service Tools
D7E Track-Type Tractor Hydraulic, HVAC and Electrical Systems Implement Movement Without Request
2010/08/25 A New Routing Is Now Available for the Valve Harness Assembly (Seat Air Compressor) on Certain Caterpillar Machines {7312, 731S, 7324}
D11T, D8T and D9T Track-Type Tractors VIMSTM 3G / Product Link Electronic Control Module (ECM) - Flash Program