Configuration
将一台计算机连接到 Product Link 系统
所需软件
确认 PL522 和 523 已经安装了最新版本的闪存文件。
所支持的硬件连接
通过 Cat ET 利用 CA-2 或 CA-3 配置 PL522 和 523 ECM。
仅限于安装 - 在机器维修接头和 PC 串行端口或并行端口之间连接通信适配器总成硬件。 为 "Caterpillar 通信适配器 II (RP1210)" 配有 Cat ET "通信接口设备"。
注: 在 Cat ET 的 "Utilities(应用程序)"菜单、"Preferences(首选项)"下拉菜单中找到 "CommuniCations Interface Device(通信接口设备)"的配置参数。
为 Cat ET 配置计算机接口通信
以下屏幕示例显示了通过为计算机配置通信来通过通信适配器 II 使用 Cat ET 的过程。
- 利用通信适配器总成将装有必要 Cat ET 软件的计算机连接到导线线束的串行维修接头上。
- 选择工具栏上的 "Utilities(应用程序)"。
- 从下拉菜单中选择 "Preference(首选项)"。
Show/hide table
图 1 | g02225153 |
- 从 "CommuniCations(通信)"选项卡,单击下拉菜单后选择 "Caterpillar CommuniCations Adapter II(Caterpillar 通信适配器 II)"。
Show/hide table
图 2 | g01361214 |
Cat ET 的"首选项"选择 |
配置Product Link PL522 和 523
本节通过为用户提供信息,帮助其配置采购软件启用附件 (SEA 所需要的机器序列号。
- 可以通过三种途径访问配置屏幕。 选择下列选项之一:
- 选择 "Service(维修)"和选择菜单栏上的 "Configure(配置)"。
- 按 "F5" 键。
- 选择工具栏上的 "ECM Configuration(ECM 配置)"图标。
- 选择 "Service(维修)"和选择菜单栏上的 "Configure(配置)"。
- 确保已经采取正确的步骤将装有 Cat ET 软件的计算机连接到了Product Link系统。 请参考"将一台计算机连接到 Product Link 系统"。
- 单击 "Connect(连接)"图标或单击菜单栏上的 "File(文件)"。 通过单击下拉菜单中的 "Connect(连接)"建立与 PL522 和 523 间的通信。
- 计算机已经连接到 PL522 或 523 后,单击 "Configuration Tool(配置工具)"图标。 选择 "Service(维修)"菜单、"Configuration(配置)"下拉菜单查看 Configuration(配置)屏幕。
- 双击或选择目标参数。 单击 "Change(更改)"。 带有向下滚动列表的对话框出现,显示所有可能的参数值。
- 更改每个参数后单击 "OK" 返回 Configuration(配置)屏幕。
请参考系统操作, "指令",以了解关于注册 Product Link 系统的信息。
Caterpillar Information System:
Product Link - PL522/523 System Components
Product Link - PL522/523 System Overview
12M Series 2, 140M Series 2 and 160M Series 2 Motor Graders Hydraulic and Steering System Pump Control Valve (Implement, Steering) - Test and Adjust
C27 and C32 Tier 4 Engines Diagnostic Capabilities
12M Series 2, 140M Series 2 and 160M Series 2 Motor Graders Hydraulic and Steering System Pilot Pressure - Test and Adjust
C18 Generator Set Engine Oil and Filter - Change
793F Series AC, 795F Series AC and 795F Series AC XQ Off-Highway Trucks VIMS 3G, Monitoring, and Truck Payload Measurement System (TPMS) MID 162 - CID 2183 - FMI 13
793F Series AC, 795F Series AC and 795F Series AC XQ Off-Highway Trucks VIMS 3G, Monitoring, and Truck Payload Measurement System (TPMS) MID 162 - CID 0890 - FMI 09
793F Series AC, 795F Series AC and 795F Series AC XQ Off-Highway Trucks VIMS 3G, Monitoring, and Truck Payload Measurement System (TPMS) MID 161 - CID 0246 - FMI 09
793F Series AC, 795F Series AC and 795F Series AC XQ Off-Highway Trucks VIMS 3G, Monitoring, and Truck Payload Measurement System (TPMS) MID 162 - CID 3050 - FMI 14
793F Series AC, 795F Series AC and 795F Series AC XQ Off-Highway Trucks VIMS 3G, Monitoring, and Truck Payload Measurement System (TPMS) MID 162 - CID 3050 - FMI 09
793F Series AC, 795F Series AC and 795F Series AC XQ Off-Highway Trucks VIMS 3G, Monitoring, and Truck Payload Measurement System (TPMS) MID 161 - CID 3050 - FMI 14
C9.3 Engines for Caterpillar Built Machines Sensor Calibration Required - Test
C15 and C18 Tier 4 Final Engines Engine Oil Pressure - Test
16M Series 3 and 18M Series 3 Motor Grader Steering System - Purge
C7.1 Industrial Engine and Generator Set ARD Failed to Ignite
2010/07/02 New Bolts Are Available for the Clutch Disc Inside the Torque Converter on Large Wheel Loaders, Landfill Compactors, and Wheel Dozers {3101}
C27 and C32 Engines for Caterpillar Built Machines Aftercooler - Test - If Equipped
Product Link - PL522/523 Installation Parameters Configure
Product Link - PL522/523 Spare Input Configure
Product Link - PL522/523 Commands
797 and 797B Off-Highway Truck/Tractors Braking System Retarder Function
Product Link - PL522/523 General Information
259B3 Compact Track Loader, 247B3 and 257B Series 3 Multi Terrain Loaders and 216B Series 3, 226B3, 236B3, 242B Series 3 and 252B Series 3 Skid Steer Loaders Piston Motor (Hydrostatic)