XQ Auto Paralleling Caterpillar


General Maintenance Information

Usage:

PMG3516 KAD

------ DANGER! ------

High voltage may be present. The power source must be disconnected before working on the equipment. Failure to disconnect the power source could result in injury or death. Verify that the equipment is not energized before performing any maintenance. This work must be performed by trained personnel with correct tools and procedures. Bodily contact with electrical potential will cause personal injury or death.


------ WARNING! ------

An accumulation of dust or foreign material can cause a fire. Serious personal injury and damage to the equipment can occur. Clean the equipment by using a brush, vacuum cleaner or clean cloth that does not leave lint.

----------------------

Disconnect all power sources before the equipment is serviced.

Remove all loads. Shut down the generator set before the equipment is serviced.

Disconnect the generator circuit breaker from the generator bus by placing the circuit breaker switch in the "PULL TO LOCK" position. See OMM, "Generator Circuit Breaker".

Remove the fuses that are used in circuits going to the load side (or bus side) of the generator breaker. Removing the fuses ensures that control circuits are not powered from external sources which are paralleled to the generator such as the utility system, or other generator sets.

See OMM, "Switchgear - Check" for further maintenance information.

Caterpillar Information System:

C18 Marine Engine Closed Crankcase Ventilation (CCV) Fumes Disposal Filter - Replace
C27 and C32 Tier 4 Engines Diagnostic Trouble Codes
Hazardous Area Shift Selector Application and Installation Guide for Petroleum Transmissions{3065, 7490} Hazardous Area Shift Selector Application and Installation Guide for Petroleum Transmissions{3065, 7490}
C7.1 Industrial Engine and Generator Set NRS Mass Flow Rate Problem
C27 PET GEN SET Electric Power Generation and C27 KNOCKDOWN K Petroleum Power Train Package Cold Weather Starting
C27 PET GEN SET Electric Power Generation and C27 KNOCKDOWN K Petroleum Power Train Package Space Heater - Test
C27 PET GEN SET Electric Power Generation and C27 KNOCKDOWN K Petroleum Power Train Package Belts - Inspect/Adjust/Replace
2010/05/31 Correct Cylinder Head Options Are Now Used for Certain 3412 and 3412C Marine Engines {1102, 1121, 1123, 1209}
C27 PET GEN SET Electric Power Generation and C27 KNOCKDOWN K Petroleum Power Train Package Engine Crankcase Breather - Clean
C27 PET GEN SET Electric Power Generation and C27 KNOCKDOWN K Petroleum Power Train Package Control Panel - Inspect/Test
C27 and C32 Tier 4 Engines Speed/Timing - Test
Procedure to Salvage Tang Slots on Transmission and Brake Pistons {0679, 3160, 4011, 4251} Procedure to Salvage Tang Slots on Transmission and Brake Pistons {0679, 3160, 4011, 4251}
C27 and C32 Tier 4 Engines Engine Monitoring Parameters
G3304B and G3306B Engines Catalytic Converter
2010/06/10 Improvements Have Been Made to Remanufactured Fuel Injectors on C15 and 3406E Engines {1251, 1290}
2010/05/31 Improvements Have Been Made to Remanufactured Fuel Injectors on C15 and 3406E Engines {1251, 1290}
C18 Marine Generator Set Maintenance Recommendations
C18 Marine Engine Maintenance Recommendations
325 VM and VH Variable Gauge Undercarriage Front Idler, Recoil Spring and Hydraulic Track Adjuster - Remove and Install
Repair of Transmission, Torque Converter, and Torque Divider Shafts {3000, 3063, 3100} Repair of Transmission, Torque Converter, and Torque Divider Shafts {3000, 3063, 3100}
C27 and C32 Tier 4 Engines Acceleration Is Poor or Throttle Response Is Poor
C27 and C32 Tier 4 Engines Pressure Sensor - Calibrate
797F and 797F XQ Off-Highway Trucks Machine Systems Hydraulic Tank (Brake, Hoist, Steering) - Remove and Install
C27 and C32 Tier 4 Engines Injector Solenoid - Test
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.