C13, C15, and C18 Tier 4 Final Engines Caterpillar


Engine Oil Pump

Usage:

826K 232




图 1g02983476

表 1
161-4113 发动机机油泵总成技术规格 
项目  数量  零件  技术规格说明 
2S-2760 弹簧  在测试力下的长度为 117.14 mm (4.612 in)
测试力为 499 ± 24 N (112 ± 5 lb)
测试后的自由长度约为 152.91 mm (6.020 in)。 
4N-5273 泵传动轴  直径为 22.217 ± 0.005 mm (0.8747 ± 0.0002 in)
长度为 157.5 ± 0.8 mm (6.20 ± 0.03 in)
机油泵盖中用于安装泵传动轴衬套的孔径为 25.400 ± 0.013 mm (1.0000 ± 0.0005 in)。 
4N-5273 泵传动轴  直径为 22.217 ± 0.005 mm (0.8747 ± 0.0002 in)
长度为 139.7 ± 0.8 mm (5.50 ± 0.03 in)
机油泵盖中用于安装泵传动轴衬套的孔径为 25.400 ± 0.013 mm (1.0000 ± 0.0005 in)。 
1W-7240 齿轮  长度为 79.375 ± 0.025 mm (3.1250 ± 0.0010 in)
机油泵体中的孔深度为 79.502 ± 0.020 mm (3.1300 ± 0.0008 in)。 
127-6356 泵盖  使 8S-6511 衬套 (7) 和泵盖的端面平齐。 


图 2g02983477
(1) 235-1587 泵体

表 2
项目  数量  零件  技术规格说明 
8M-8489 定位销  定位销在机油泵中的安装深度 (A) 为 6.4 ± 0.5 mm (0.25 ± 0.02 in)。 
7N-2156 衬套  安装衬套,使衬套与机油泵体的外侧平齐。
机油泵体中心线与衬套接头之间的角度为 30 ± 15 度。
安装深度 (C) 为 0.30 ± 0.25 mm (0.012 ± 0.010 in)。 

Caterpillar Information System:

C13 Industrial Engines Temperature Sensor (NOx Reduction System) - Cooled Diesel Exhaust Gases
797F Off-Highway Truck Power Train Gear Pump (Rear Axle Lubrication) - Assemble
797F Off-Highway Truck Power Train Gear Pump (Rear Axle Lubrication) - Disassemble
TH55FT-E70 and TH55FT-E90 Transmissions Component Location
EMCP4.3/4.4 Data Link
797F Off-Highway Truck Power Train Gear Pump (Rear Axle Lubrication) - Remove and Install
C9.3 Tier 4 Final Engines Fuel Filter Base
2010/03/22 A Procedure to Properly Torque the Fittings on the Fuel Manifold Group on Certain C13 and C15 On-Highway Truck Engines Is Available {1274, 1380, 1702}
Torque Converter, Divider, Drive Line, and Drive Axle Reuse and Salvage Manual Contents {0374, 3000, 3050, 3100, 3250, 3251, 3253, 3258} Torque Converter, Divider, Drive Line, and Drive Axle Reuse and Salvage Manual Contents {0374, 3000, 3050, 3100, 3250, 3251, 3253, 3258}
2010/10/08 A Slave Relay Should be Used for Customer Connections to EMCP 3 On Certain Generator Sets {4490}
C13 Industrial Engines Pressure Sensor (NRS Absolute)
2010/03/10 A New Screw Is Available for the Rocker Arm Assemblies of Some Machine Engines {1123}
C13, C15, and C18 Tier 4 Interim Engines Configuration Parameters
C11 and C13 Engines Piston and Rings
C175-16 Petroleum Generator Set Engines Monitoring System
2013/01/16 New Liner Seals Are Used and Inserts Are Available for All 3500 Engines {1201}
2010/06/25 New Liner Seals Are Used and Inserts Are Available for All 3500 Engines {1201}
C15 Petroleum Generator Set Engines Speed/Timing Sensor
C13, C15, and C18 Tier 4 Final Engines Boost Pressure Sensor
C13, C15, and C18 Tier 4 Final Engines Engine Oil Pan
C9.3 Tier 4 Final Engines Belt Tensioner
2010/03/25 An Updated Fuel Pressure Is Used In System Operation, Testing and Adjusting Manuals For C27 and C32 Engines {1250, 1256}
2010/03/25 An Updated Fuel Pressure Is Used In System Operation, Testing and Adjusting Manuals For C27 and C32 Machine Engines {1250, 1256}
EMCP4.3/4.4 Electronic Control Module (Generator Set)
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.