797F Off-Highway Truck Power Train Caterpillar


Gear Pump (Rear Axle Lubrication) - Assemble

Usage:

797F LAJ


组装步骤

表 1
所需工具    
工具     零件号     零件描述     数量    
A     1P-0510     冲头总成     1    



    图 1g02117413



    图 2g02118155

  1. 安装 O 形密封圈 (28) 和 O 形密封圈 (27) 。

  1. 使用工具 (A) 将轴承 (26) 安装至尺寸 (X) 。 尺寸 (X) 为 1.50 ± 0.25 mm (0.060 ± 0.001 in)。 安装轴承 (26) 时必须使轴承接头安装到尺寸 (Y) 。 尺寸 (Y) 为 30° ± 15°。



    图 3g02117393

  1. 拆下机油泵齿轮 (25) 。



    图 4g02117300

  1. 安装泵体组件 (24) 。 安装 O 形密封圈 (23) 。



    图 5g02118435



    图 6g02118456

  1. 安装 O 形密封圈 (22) 。

  1. 使用工具 (A) 将轴承 (21) 安装至尺寸 (X) 。 尺寸 (X) 为 1.50 ± 0.25 mm (0.060 ± 0.001 in)。 安装轴承 (21) 时必须使轴承接头安装到尺寸 (Y) 。 尺寸 (Y) 为 30° ± 15°。 拆下轴承 (21) 。



    图 7g02117294

  1. 拆下机油泵盖 (20) 。 安装 O 形密封圈 (19) 。



    图 8g02117281

  1. 安装键 (18) 。



    图 9g02117260

  1. 安装齿轮 (17) 。 安装泵体组件 (16) 。



    图 10g02117256



    图 11g02118374

  1. 使用工具 (A) 将轴承 (15) 安装至尺寸 (X) 。 尺寸 (X) 为 1.50 ± 0.25 mm (0.060 ± 0.001 in)。 安装轴承 (15) 时必须使轴承接头安装到尺寸 (Y) 。 尺寸 (Y) 为 30° ± 15°。

  1. 安装 O 形密封圈 (14) 。



    图 12g02117253

  1. 安装泵体组件 (13) 。



    图 13g02117194

  1. 安装齿轮 (11) 和键 (12) 。



    图 14g02117213

  1. 安装 O 形密封圈 (10) 。 安装管 (9) 和法兰 (8) 。



    图 15g02117183



    图 16g02118415

  1. 使用工具 (A) 将轴承 (6) 安装至尺寸 (X) 。 尺寸 (X) 为 1.50 ± 0.25 mm (0.060 ± 0.001 in)。 安装轴承 (6) 时必须使轴承接头安装到尺寸 (Y) 。 尺寸 (Y) 为 30° ± 15°。

  1. 安装 O 形密封圈 (7) 。



    图 17g02117174

  1. 拆下机油泵盖 (5) 。 安装螺栓 (4) 。



    图 18g02117181

  1. 安装 O 形密封圈 (3) 。



    图 19g02117169

  1. 安装接头 (2) 。 安装螺栓 (1) 。

End By: 拆下齿轮泵(后桥润滑)。

Caterpillar Information System:

797F Off-Highway Truck Power Train Gear Pump (Rear Axle Lubrication) - Disassemble
TH55FT-E70 and TH55FT-E90 Transmissions Component Location
EMCP4.3/4.4 Data Link
797F Off-Highway Truck Power Train Gear Pump (Rear Axle Lubrication) - Remove and Install
C9.3 Tier 4 Final Engines Fuel Filter Base
2010/03/22 A Procedure to Properly Torque the Fittings on the Fuel Manifold Group on Certain C13 and C15 On-Highway Truck Engines Is Available {1274, 1380, 1702}
Torque Converter, Divider, Drive Line, and Drive Axle Reuse and Salvage Manual Contents {0374, 3000, 3050, 3100, 3250, 3251, 3253, 3258} Torque Converter, Divider, Drive Line, and Drive Axle Reuse and Salvage Manual Contents {0374, 3000, 3050, 3100, 3250, 3251, 3253, 3258}
2010/10/08 A Slave Relay Should be Used for Customer Connections to EMCP 3 On Certain Generator Sets {4490}
C13 Industrial Engines Pressure Sensor (NRS Absolute)
2010/03/10 A New Screw Is Available for the Rocker Arm Assemblies of Some Machine Engines {1123}
2010/03/12 A New Screw Is Available for the Rocker Arm Assemblies of Some Commercial Engines {1123}
2010/03/09 A New Screw Is Available for the Rocker Arm Assemblies of Some Truck Engines {1123}
C13 Industrial Engines Temperature Sensor (NOx Reduction System) - Cooled Diesel Exhaust Gases
C13, C15, and C18 Tier 4 Final Engines Engine Oil Pump
C13, C15, and C18 Tier 4 Interim Engines Configuration Parameters
C11 and C13 Engines Piston and Rings
C175-16 Petroleum Generator Set Engines Monitoring System
2013/01/16 New Liner Seals Are Used and Inserts Are Available for All 3500 Engines {1201}
2010/06/25 New Liner Seals Are Used and Inserts Are Available for All 3500 Engines {1201}
C15 Petroleum Generator Set Engines Speed/Timing Sensor
C13, C15, and C18 Tier 4 Final Engines Boost Pressure Sensor
C13, C15, and C18 Tier 4 Final Engines Engine Oil Pan
C9.3 Tier 4 Final Engines Belt Tensioner
2010/03/25 An Updated Fuel Pressure Is Used In System Operation, Testing and Adjusting Manuals For C27 and C32 Engines {1250, 1256}
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.