C15 and C18 Industrial Engines Caterpillar


Water Temperature Regulator Housing - Remove and Install - For Series Turbocharger Applications

Usage:

C18 BDN

Removal Procedure

Start By:

  1. Remove the precooler. Refer to Disassembly and Assembly, "Precooler - Remove and Install".


NOTICE

Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.

Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products.

Dispose of all fluids according to local regulations and mandates.



NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.


  1. Drain the coolant from the cooling system into a suitable container for storage or disposal. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change".



    Illustration 1g02115322

  1. Remove tube assembly (1) .



    Illustration 2g02115513

  1. Remove bolts (3) and harness assembly (2) .

  1. Remove the water temperature regulator housing (4) .



    Illustration 3g02115534

  1. Remove elbow (5) .

  1. Remove the bolts (9) and remove manifold (7) from housing (6) .

  1. Remove the temperature sensor (8) .



    Illustration 4g02117173

  1. Remove water regulators (10) from housing (7) .

  1. Remove tube (11) and the O-ring seals.

Installation Procedure


NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.


Note: Check the O-ring seals, the gaskets, and the seals for wear or for damage. Replace the components, if necessary.

  1. Install the water temperature regulator housing in reverse order.

  1. Fill the cooling system. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change".

Caterpillar Information System:

C27 PET GEN SET Electric Power Generation and C27 KNOCKDOWN K Petroleum Power Train Package Generator Bearing Temperature - Test/Record
C11 and C13 Engines Water Pump
Inspection and Reuse of Critical Fasteners Used in All Engines {7553, 7553} Inspection and Reuse of Critical Fasteners Used in All Engines {7553, 7553}
C27 and C32 Engines for Caterpillar Built Machines Cylinder Head Valves
C15 and C18 Industrial Engines Precooler - Remove and Install - For Series Turbo Applications
C-10, C-12 and C-15 On-Highway Engines Configuration Parameters - Customer Specified Parameters
C13 Industrial Engines Temperature Sensor (NOx Reduction System) - Cooled Diesel Exhaust Gases
C9.3 Tier 4 Final Engines Temperature Sensor (NOx Reduction System)
Installation and Initial Start-Up Procedure for G3508B A3 Engines{1000} Installation and Initial Start-Up Procedure for G3508B A3 Engines{1000}
C13, C15, and C18 Tier 4 Final Engines Inlet Manifold Temperature Sensor - Charge Air Cooler Outlet
C13 Industrial Engines Fuel Pressure Sensor
C27 and C32 Engines for Caterpillar Built Machines Camshaft
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit Machine Systems Swing Drive - Disassemble
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit Machine Systems Swing Drive - Assemble
C27 and C32 Tier 4 Engines Pressure Sensor (NRS Differential)
2010/03/09 A New Screw Is Available for the Rocker Arm Assemblies of Some Truck Engines {1123}
2010/03/12 A New Screw Is Available for the Rocker Arm Assemblies of Some Commercial Engines {1123}
2010/03/10 A New Screw Is Available for the Rocker Arm Assemblies of Some Machine Engines {1123}
C13 Industrial Engines Pressure Sensor (NRS Absolute)
2010/10/08 A Slave Relay Should be Used for Customer Connections to EMCP 3 On Certain Generator Sets {4490}
Torque Converter, Divider, Drive Line, and Drive Axle Reuse and Salvage Manual Contents {0374, 3000, 3050, 3100, 3250, 3251, 3253, 3258} Torque Converter, Divider, Drive Line, and Drive Axle Reuse and Salvage Manual Contents {0374, 3000, 3050, 3100, 3250, 3251, 3253, 3258}
2010/03/22 A Procedure to Properly Torque the Fittings on the Fuel Manifold Group on Certain C13 and C15 On-Highway Truck Engines Is Available {1274, 1380, 1702}
C9.3 Tier 4 Final Engines Fuel Filter Base
797F Off-Highway Truck Power Train Gear Pump (Rear Axle Lubrication) - Remove and Install
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.