New Settings Are Now Used For EMCP 3 On Certain Generator Sets {4490}
- Electric Power Generation:
- C1.5 (S/N: GBD1-UP)
- C2.2 GEN SET (S/N: GBE1-UP)
- C4.4 GEN SET (S/N: D4B1-UP)
- C6.6 GEN SET (S/N: N6D1-UP)
Description of Change: New settings are now used for the EMCP 3 on certain Generator Sets. Updating with these settings will enhance the reliability of the EMCP 3.
Adaptable To: The effectivity for this change is shown in table 1.
Show/hide table
Effectivity     | ||
Model     | Adaptable to Machines     | Effective With Machines     |
C1.5     | S/N:GBD1-219     | S/N:GBD220-UP     |
C2.2     | S/N:GBE1-377     | S/N:gbe378-UP     |
C4.4     | S/N:D4B1-1601     | S/N:D4B1602-UP     |
C6.6     | S/N:N6D1-1547     | S/N:N6D1548-UP     |
- Start the set position for the aid activation timer in the EMCP 3 configuration at 0 seconds, with a rule that if the National Fire Protection Agency (NFPA110) and Jacket Water Heater (JWH) options are selected, the value in the factory settings rules is set to 0.
- Set the "Service Maintenance Interval Warning Event Response " configuration as "Disable" condition for PEPCNN product.
- Change the display for the "Pressure Units Configuration" from "Bar" to "PSI " for PEPCNN product.
- Change the display for the "Temperature Units Configuration" from "Celsius" to "Fahrenheit" for PEPCNN product.
- Change the display for the "Volume Units Configuration" from "Liter" to "Gallon" for PEPCNN product.
- Change the event notification delay time for the "Low Battery Charging System Volatage Warning" from 30 seconds to 60 seconds for all product.
Caterpillar Information System:
C13, C15, and C18 Tier 4 Final Engines Speed/Timing Sensor
C27 PET GEN SET Electric Power Generation and C27 KNOCKDOWN K Petroleum Power Train Package Generator Bearing - Replace - SR5 Generator Bearings
C15 and C18 Petroleum Generator Sets Generator Bearing - Inspect
349F and 352F Excavators Hydraulic System Oil - Change
349F and 352F Excavators Hydraulic System Main Hydraulic Pump Air - Purge
C15 and C18 Engines for Caterpillar Built Machines Engine Oil Filter Base
C27 Generator Set Engines Air Lines
349F and 352F Excavators Hydraulic System Oil Filter (Pilot) - Replace
C18 Generator Set Electronic Modular Control Panel 3 (EMCP 3)
349F and 352F Excavators Hydraulic System Oil Filter (Case Drain) - Replace
C280-16 Petroleum Engine Temperature Sensor
797F and 797F XQ Off-Highway Trucks Machine Systems Air Tank (Primary) - Remove and Install
G3500 Generator Sets Additional Messages
G3512E Generator Set Engine Fuel Metering Valve - Test
C7.1 Industrial Engine and Generator Set Ether Starting Aid - Test
G3500 Generator Sets Model View Illustrations
2010/08/17 New Turbochargers Are Used on Some C18 Industrial Engines {1052, 1053}
C27 and C32 Engines for Caterpillar Built Machines Camshaft
C13 Industrial Engines Fuel Pressure Sensor
C13, C15, and C18 Tier 4 Final Engines Inlet Manifold Temperature Sensor - Charge Air Cooler Outlet
Installation and Initial Start-Up Procedure for G3508B A3 Engines{1000} Installation and Initial Start-Up Procedure for G3508B A3 Engines{1000}
C9.3 Tier 4 Final Engines Temperature Sensor (NOx Reduction System)
C13 Industrial Engines Temperature Sensor (NOx Reduction System) - Cooled Diesel Exhaust Gases
C-10, C-12 and C-15 On-Highway Engines Configuration Parameters - Customer Specified Parameters