Customer Specified Parameters Worksheet
Show/hide table
| Customer Specified Parameters Worksheet | |
|---|---|
| ECM Identification Parameter | |
| Equipment ID | |
| Engine Rating Parameter | |
| Rating Number | |
| Speed Control | |
| Low Idle Speed | |
| Engine Configuration Parameter | |
| Ether Solenoid Configuration | |
| Engine Idle Shutdown | |
| Minimum Ambient Air Temperature | |
| Maximum Ambient Air Temperature | |
| Shutdown Enable Status | |
| Shutdown Delay Time | |
| Ambient Temperature Override Enable Status | |
| Air Shutoff | |
| Air Shutoff | |
| Aftertreatment Configuration | |
| ARD Auto Regeneration Enable Status | |
| DPF #1 Soot Loading Sensing System Configuration Code | |
| High Soot Load Aftertreatment Protection | |
| Multiple Engines on J1939 | |
| Engine Location | |
| PTO and Throttle Lock Parameters | |
| Throttle Lock Feature Installation Status | |
| PTO Mode | |
| Throttle Lock Engine Set Speed 1 | |
| Throttle Lock Engine Set Speed 2 | |
| Throttle Lock Increment Speed Ramp Rate | |
| Throttle Lock Decrement Speed Ramp Rate | |
| Throttle Lock Engine Set Speed Increment | |
| Throttle Lock Engine Set Speed Decrement | |
| Miscellaneous | |
| Monitoring Mode Shutdowns | |
| Monitoring Mode Derates | |
| Limp Home Desired Engine Speed | |
| Engine Acceleration Rate | |
| Engine Speed Deceleration Ramp Rate | |
| Intermediate Engine Speed | |
| Engine Fan Control | |
| Engine Fan Control | |
| Engine Fan Type Configuration | |
| Pulley Ratio | |
| Temperature Error Increasing Hysteresis | |
| Temperature Error Decreasing Hysteresis | |
| Current Ramp Rate | |
| Fan Speed | |
| Top Fan Speed | |
| Minimum Desired Fan Speed | |
| Solenoid Minimum Current | |
| Solenoid Maximum Current | |
| Solenoid Dither Frequency | |
| Solenoid Dither Amplitude | |
| Cooling Fan Temperatures | |
| Charge Air Cooler Outlet Temperature Input Enable | |
| Maximum Air Flow Charge Air Cooler Outlet Temperature | |
| Minimum Air Flow Charge Air Cooler Outlet Temperature | |
| Coolant Temperature Input Enable Status | |
| Maximum Air Flow Coolant Temperature | |
| Minimum Air Flow Coolant Temperature | |
| Transmission Oil Temperature Input Enable Status | |
| Maximum Air Flow Transmission Oil Temperature | |
| Minimum Air Flow Transmission Oil Temperature | |
| Hydraulic Oil Temperature Input Enable Status | |
| Maximum Air Flow Hydraulic Oil Temperature | |
| Minimum Air Flow Hydraulic Oil Temperature | |
| Auxiliary #1 Temperature Input Enable Status | |
| Maximum Air Flow Auxiliary #1 Temperature | |
| Minimum Air Flow Auxiliary #1 Temperature | |
| Auxiliary #2 Temperature Input Enable Status | |
| Maximum Air Flow Auxiliary #2 Temperature | |
| Minimum Air Flow Auxiliary #2 Temperature | |
| Fan Reversing | |
| Reversing Feature | |
| Reverse Operation Early Termination Enable Status | |
| Manual Purge | |
| Suspend Purge | |
| Purge Cycle Interval | |
| Purge Cycle Duration | |
| Configurable Inputs | |
| Coolant Level Switch | |
| Air Filter Restriction Switch Installation Status | |
| Air Filter Restriction Switch Configuration | |
| Water in Fuel Switch Installation Status | |
| User Defined Switch Installation Status | |
| Auxiliary Temperature Sensor Installation Status | |
| Auxiliary Pressure Sensor Installation Status | |
| Fuel Filter Differential Pressure Switch Configuration | |
| Diesel Particulate Filter Regeneration Force/Inhibit Switch Installation | |
| Diesel Particulate Filter Regeneration Inhibit Indicator Installation | |
| Diesel Particulate Filter Soot Loading Indicator Installation | |
| Regeneration Active Indicator Installation | |
| J1939 Continuous Fault Handling | |
| Remote Torque Speed Control Enable Status | |
| System Settings | |
| System Operating Voltage Configuration | |
| Passwords | |
| Customer Password 1 | |
| Customer Password 2 | |
| Security Access Parameters | |
| CAN Communication Protocol Write Security | |
| CAN Communication Protocol Read Security | |
Caterpillar Information System:
C7.1 Industrial Engine and Generator Set Customer Specified Parameters Table
3508C, 3512C and 3516C Locomotive Engines Water Lines
C7.1 Industrial Engine and Generator Set Mode Selection Circuit - Test
3508C, 3512C and 3516C Locomotive Engines Water Lines
793F Off-Highway Truck Engine Supplement Turbocharger - Remove and Install
793F Off-Highway Truck Engine Supplement Damper - Remove and Install
797F and 797F XQ Off-Highway Truck Steering System Oil Filter (Hydraulic Fan, Steering Pump Case Drain)
2009/10/01 Improved Exhaust Components and Heat Shields Are Used on Some G3520C Engines {1059, 1067}
C4.4 Industrial Engine Cooling System Supplemental Coolant Additive (SCA) - Test/Add
C4.4 Industrial Engine Cooling System Coolant Extender (ELC) - Add
3508C, 3512C and 3516C Locomotive Engines Water Lines
3508C, 3512C and 3516C Locomotive Engines Air Inlet and Exhaust Lines
797F and 797F XQ Off-Highway Truck Braking System Oil Filter (Brake Cooling, Hoist)
2009/08/31 Diagnostic Process for Fuel Rail Pressure Sensor {127A, 1439}
2009/08/17 New Metal Shipping Stands for 3500 Machine Engines {1000}
2009/08/01 Diagnostic Publications for the Systems of the Hydraulic Electronic Unit Injector (HEUI) have been Updated {1100, 1126, 1250, 1251, 1261, 1290}
2009/08/10 Diagnostic Publications for the Systems of the Hydraulic Electronic Unit Injector (HEUI) have been Updated {1100, 1126, 1250, 1251, 1261, 1290}
793F and 797F Off-Highway Trucks Chassis Electronic Control System Glossary of Electrical Terms
C13 Industrial Engines Turbocharger
C18 Industrial Engine Aftercooler - Test
2009/08/03 A New Bolt Is Used on the Valve Mechanism Gp of All 3500 Machine Engines {1102, 1107, 1120, 1121, 1123, 1209}
2009/08/03 The Connector for the Chassis Harness and the Platform Harness Should Be Tightened to the Specified Torque on Certain Excavators {1408}
C27 PET GEN SET Electric Power Generation and C27 KNOCKDOWN K Petroleum Power Train Package Battery Disconnect Switch - If Equipped
3516B Engine for 994F and 994H Wheel Loaders Electronic Service Tool Does Not Communicate