C7.1 Industrial Engine and Generator Set Caterpillar

Customer Specified Parameters Table

Usage:

C7.1 770

Show/hide table

Table 1
Customer Specified Parameters
ECM Parameter	Possible Values	Default Value
ECM Identification Parameter
Equipment ID	17 Digits Available characters are dependent on the service tool that is used	Not Programmed
Engine Rating Parameter
Rating Number	1 to 4	1
Speed Control
Low Idle Speed	700 to 1200 rpm	750 rpm
Engine Configuration Parameter
Ether Solenoid Configuration	Not Installed Continuous Flow Solenoid	Not Installed
Engine Idle Shutdown
Minimum Ambient Air Temperature	0 to 29 degrees C	0 degrees C
Maximum Ambient Air Temperature	30 to 100 degrees C	30 degrees C
Shutdown Enable Status	Disabled Enabled	Disabled
Shutdown Delay Time	1 to 60 minutes	5 minutes
Ambient Temperature Override Enable Status	Disabled Enabled	Disabled
Air Shutoff
Air Shutoff	Disabled Enabled	Enabled
Aftertreatment Configuration
ARD Auto Regeneration Enable Status	Disabled Enabled	Enabled
DPF #1 Soot Loading Sensing System Configuration Code	20(Hex) to 7F(Hex)	0
High Soot Load Aftertreatment Protection	Disabled Enabled	Disabled
Multiple Engines on J1939
Engine Location	Engine #1 Engine #2 Engine #3 Engine #4 Engine #5	Engine #1
PTO and Throttle Lock Parameters
Throttle Lock Feature Installation Status	Installed Not Installed	Not Installed
PTO Mode	Ramp Up/Ramp Down Set/Resume	Set/Resume
Throttle Lock Engine Set Speed 1	Low idle speed to rated speed	700 rpm
Throttle Lock Engine Set Speed 2	Low idle speed to rated speed	700 rpm
Throttle Lock Increment Speed Ramp Rate	0 to 600 rpm/sec	400 rpm/sec
Throttle Lock Decrement Speed Ramp Rate	0 to 600 rpm/sec	400 rpm/sec
Throttle Lock Engine Set Speed Increment	0 to 200 rpm	10 rpm
Throttle Lock Engine Set Speed Decrement	0 to 200 rpm	10 rpm
Miscellaneous
Monitoring Mode Shutdowns	Disabled Enable	Enabled
Monitoring Mode Derates	Disabled Enabled	Enabled
Limp Home Desired Engine Speed	700 to 1800 rpm	1200 rpm
Engine Acceleration Rate	0 to 65503 rpm/sec	0 rpm/sec
Engine Speed Deceleration Ramp Rate	0 to 65503 rpm/sec	0 rpm/sec
Intermediate Engine Speed	0 to 2800 rpm	0 rpm
Engine Fan Control
Engine Fan Control	Off On	Off
Engine Fan Type Configuration	Viscous Clutch Variable Hydraulic	Variable Hydraulic
Pulley Ratio	Ratio	1.2:1
Temperature Error Increasing Hysteresis	Percentage	10%
Temperature Error Decreasing Hysteresis	Percentage	10%
Current Ramp Rate	Amps per Second	0.1 amps/sec
Fan Speed	Percentage	100%
Top Fan Speed	RPM	1600 rpm
Minimum Desired Fan Speed	RPM	500 rpm
Solenoid Minimum Current	Amps	0.3 Amps
Solenoid Maximum Current	Amps	1.5 Amps
Solenoid Dither Frequency	Hz	100 Hz
Solenoid Dither Amplitude	Amps	0.1 Amps
Cooling Fan Temperatures
Charge Air Cooler Outlet Temperature Input Enable	Enabled Disabled	Enabled
Maximum Air Flow Charge Air Cooler Outlet Temperature	Degrees C	45 Degrees C
Minimum Air Flow Charge Air Cooler Outlet Temperature	Degrees C	40 Degrees C
Coolant Temperature Input Enable Status	Enabled Disabled	Enabled
Maximum Air Flow Coolant Temperature	Degrees C	102 Degrees C
Minimum Air Flow Coolant Temperature	Degrees C	92 Degrees C
Transmission Oil Temperature Input Enable Status	Enabled Disabled	Enabled
Maximum Air Flow Transmission Oil Temperature	Degrees C	110 Degrees C
Minimum Air Flow Transmission Oil Temperature	Degrees C	100 Degrees C
Hydraulic Oil Temperature Input Enable Status	Enabled Disabled	Enabled
Maximum Air Flow Hydraulic Oil Temperature	Degrees C	110 Degrees C
Minimum Air Flow Hydraulic Oil Temperature	Degrees C	100 Degrees C
Auxiliary #1 Temperature Input Enable Status	Enabled Disabled	Enabled
Maximum Air Flow Auxiliary #1 Temperature	Degrees C	110 Degrees C
Minimum Air Flow Auxiliary #1 Temperature	Degrees C	100 Degrees C
Auxiliary #2 Temperature Input Enable Status	Enabled Disabled	Enabled
Maximum Air Flow Auxiliary #2 Temperature	Degrees C	110 Degrees C
Minimum Air Flow Auxiliary #2 Temperature	Degrees C	100 Degrees C
Fan Reversing
Reversing Feature	Enabled Disabled	Disabled
Reverse Operation Early Termination Enable Status	Enabled Disabled	Disabled
Manual Purge	Enabled Disabled	Disabled
Suspend Purge	Enabled Disabled	Disabled
Purge Cycle Interval	Seconds	3600 Seconds
Purge Cycle Duration	Seconds	30 Seconds
Configurable Inputs
Coolant Level Switch	Not Installed Installed	Not Installed
Air Filter Restriction Switch Installation Status	Not Installed Installed	Not Installed
Air Filter Restriction Switch Configuration	Normally Open Normally Closed	Normally Open
Water in Fuel Switch Installation Status	Not Installed Installed	Installed
User Defined Switch Installation Status	Not Installed Installed	Not Installed
Auxiliary Temperature Sensor Installation Status	Installed Not Installed	Not Installed
Auxiliary Pressure Sensor Installation Status	Installed Not Installed	Not Installed
Fuel Filter Differential Pressure Switch Configuration	Not Installed Normally Open Normally Closed	Not Installed
Diesel Particulate Filter Regeneration Force/Inhibit Switch Installation	Installed Not Installed	Not Installed
Diesel Particulate Filter Regeneration Inhibit Indicator Installation	Installed Not Installed	Not Installed
Diesel Particulate Filter Soot Loading Indicator Installation	Installed Not Installed	Not Installed
Regeneration Active Indicator Installation	Installed Not Installed	Not Installed
J1939 Continuous Fault Handling
Remote Torque Speed Control Enable Status	Enabled Disabled	Disabled
System Settings
System Operating Voltage Configuration	12 VDC 24 VDC	24 VDC
Passwords
Customer Password 1	Eight alphanumeric characters	Eight spaces
Customer Password 2	Eight alphanumeric characters	Eight spaces
Security Access Parameters
CAN Communication Protocol Write Security	Seed and Key No Security	Seed and Key
CAN Communication Protocol Read Security	Seed and Key No Security	Seed and Key