Exhaust Manifold - Remove and Install
拆卸步骤
开始:
- 拆下进气歧管。 参考拆解和组装, "进气歧管 - 拆卸和安装"。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
注意 |
---|
卡箍组件应只使用一次。 使用后弃置所有卡箍组件。 |
Show/hide table
注意 |
---|
波纹管组件应只使用一次。 使用后弃置所有波纹管。 |
- 将弹簧夹从隔热罩 (1) 的左侧拆下。
Show/hide table
图 1 | g02162817 |
Show/hide table
图 2 | g02162818 |
- 将后隔热罩从中间隔热罩上拆下。
- 将中间隔热罩从前隔热罩上拆下。
- 对隔热罩 (2) 的右侧重复此程序。
- 松开排气旁通阀接头的卡箍组件 (3) 。 断开波纹管组件 (4) 。
Show/hide table
图 3 | g02162839 |
注: 如果发动机排气旁通阀上配有盖帽而并非接头,可能无需拆卸卡箍组件 (3) 。
- 拆下螺栓 (11) 。 将歧管 (10) 从涡轮增压器上断开。 将密封垫从涡轮增压器上拆下。
- 拆下排气歧管 (7) 段的螺栓 (8) 。 拆下波纹管组件 (9) 和密封件。
- 拆下将排气歧管 (7) 固定到缸盖上的螺栓 (5) 。
- 拆下排气歧管 (7) 和排气歧管密封垫 (6) 。
- 对于其余的排气歧管,重复步骤 7 到 9。
安装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A     | 5P-3931     | 防粘结剂     | -     |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
注意 |
---|
卡箍组件应只使用一次。 使用后弃置所有卡箍组件。 |
Show/hide table
注意 |
---|
波纹管组件应只使用一次。 使用后弃置所有波纹管。 |
- 将工具 (A) 涂敷在螺栓 (5) 的螺纹上。 将排气歧管密封垫 (6) 和排气歧管 (7) 放置就位到缸盖上。 安装螺栓 (5) 。 将对角螺栓上紧到 55 ± 5 N·m (41 ± 4 lb ft) 的扭矩。 将其他对角螺栓上紧到 55 ± 5 N·m (41 ± 4 lb ft) 的扭矩。
Show/hide table
图 4 | g02162839 |
- 将工具 (A) 涂抹到螺纹、轴承表面和排气歧管 (7) 螺栓的内表面上。 将密封件、波纹管组件 (9) 和螺栓 (8) 安装到排气歧管 (7) 上。 将对角螺栓上紧到 55 ± 5 N·m (41 ± 4 lb ft) 的扭矩。 将其他对角螺栓上紧到 55 ± 5 N·m (41 ± 4 lb ft) 的扭矩。
注: 在安装过程中,确保波纹管组件处于正确的朝向。 流向箭头的方向应指向正确的方向。 波纹管组件的顶部之间间距应相等
- 对于其余的排气歧管,重复步骤 1 到 2。
- 将工具 (A) 涂抹到螺纹、轴承表面和涡轮增压器螺栓的内表面上。 安装新密封垫后将歧管 (8) 连接到涡轮增压器上。 安装螺栓 (11) 。 将螺栓上紧到 54 ± 5 N·m (40 ± 4 lb ft) 的扭矩。
- 连接波纹管组件 (4) 。 上紧排气旁通阀接头的卡箍组件 (3) 。
- 安装前隔热罩。 将中间隔热罩滑到前隔热罩的下方。
Show/hide table
图 5 | g02162818 |
Show/hide table
图 6 | g02162817 |
- 通过滑动将后隔热罩安装到中间隔热罩下方。
- 将弹簧夹安装到隔热罩 (1) 的左侧上。
- 对隔热罩 (2) 的右侧重复此程序。
End By: 安装进气歧管。 参考 拆解和组装, "进气歧管 - 拆卸和安装"。
Caterpillar Information System:
793F and 797F Off-Highway Trucks Braking System Electrical Component and Connector Locations
320 Variable Gauge OEM Undercarriage Hydraulic System Relief Valve (Travel Motor) - Test and Adjust - VM Undercarriage
3500 Engines Exhaust Elbow - Remove and Install
2009/08/17 New Injectors and Camshafts Are Now Used for Some C18 Engines That Are Installed on O & K Shovels {1210, 1290, 1901, 1920}
2009/10/28 New Brackets and New Hardware Are Used for the Upper Heat Exchanger on C18 Engines {1379}
C9.3 Engines for Caterpillar Built Machines Temperature Sensor (DPF) - Remove and Install
797F and 797F XQ Off-Highway Truck Braking System Brake Accumulator (Service)
C9.3 Engines for Caterpillar Built Machines Flame Detection Temperature Sensor - Remove and Install
3512B, 3512C, and 3516B Generator Set Engines with Dynamic Gas Blending Air Starting System
793F and 797F Off-Highway Trucks Power Train Electronic Control System Power Train Has Unusual Noise
793F and 797F Off-Highway Trucks Power Train Electronic Control System Rear Axle Oil Temperature Is High
793F and 797F Off-Highway Trucks Power Train Electronic Control System Transmission Does Not Shift
CX35-P800-C18I and CX35-P800-C27I Petroleum Power Train Packages and CX35-P800 Petroleum Transmission Engine Does Not Crank
CX35-P800-C18I and CX35-P800-C27I Petroleum Power Train Packages and CX35-P800 Petroleum Transmission Transmission Does Not Respond to Shift Selector
CX35-P800-C18I and CX35-P800-C27I Petroleum Power Train Packages and CX35-P800 Petroleum Transmission Transmission - Calibrate
793F and 793F CMD Off-Highway Truck Braking System Diverter Valve (Parking, Secondary Brake)
797F and 797F XQ Off-Highway Truck Power Train Final Drive, Brake and Wheel
797F and 797F XQ Off-Highway Truck Braking System Brake Accumulator (Parking)
C7.1 Industrial Engine and Generator Set Oil Contains Fuel
C7.1 Industrial Engine Crankshaft Vibration Damper - Inspect
797F and 797F XQ Off-Highway Truck Power Train Gear Pump (Transmission Charging and Scavenge)
C9.3 Engines for Caterpillar Built Machines Air Cleaner Housing - Remove and Install
C9.3 Engines for Caterpillar Built Machines Muffler - Remove and Install
C13, C15, and C18 Tier 4 Interim Engines ARD Does Not Activate