G3304B and G3306B Engines Caterpillar


Turbocharger - Assemble

Usage:

G3304B A4E

组装步骤

表 1
所需工具    
工具     零件号     零件说明     数量    
A     9S-6363     固定夹具     1    
B     9S-6343     夹具组件     1    
C     1P-1861     挡圈钳     1    
D     FT-0745     改装钳     1    
E     8T-5096     千分表总成     1    
F     4L-7464     硅脂     -    
G     5P-3931     防粘结剂     -    

注: 清洁度是一项重要的因素。 组装之前,应使用清洗剂彻底清洁所有零件。 让零件风干。 不要使用抹布擦干零件。 棉绒可能会留在零件上,可能导致以后出现故障。 检查所有零件。 如果任何零件磨损或损坏,则应使用新零件进行更换。

  1. 确保芯组件中的所有油道清洁,没有污垢和异物。

  1. 将清洁的发动机机油涂抹在芯组件的所有零件上。



    图 1g01930813



    图 2g01930815

    注: 安装挡圈 (18) 、 (19) 、 (24) 和 (23) 时,挡圈的圆边必须朝着轴承。

  1. 使用工具 (D) 安装挡圈 (18) 和 (19) 。 将挡圈 (18) 、轴承 (14) 和挡圈 (19) 安装在芯组件的压缩机端。

  1. 转过芯组件,使用工具 (D) 安装挡圈 (24) 和 (23) 。

  1. 将挡圈 (24) 、轴承 (22) 、套筒 (25) 和挡圈 (23) 安装在芯组件的涡轮端上。



    图 3g01930816

  1. 将密封圈在芯组件 (3) 上安放到位。 检查密封圈的轴向间隙。 最大允许轴向间隙为 0.23 mm (0.009 in)。



    图 4g01930817

  1. 用工具 (F) 填充围绕涡轮轴 (7) 一整圈的槽 (25) 的一半深度或更多。



    图 5g01930818

    注: 安装期间小心不要折断密封圈 (8) 。

  1. 将密封圈 (8) 安装在涡轮轴 (7) 上。

    注: 确保涡轮轴 (7) 上的密封圈 (8) 正确地安装在芯组件上。




    图 6g01930819

  1. 将护罩 (6) 在芯组件上放置到位。

  1. 将涡轮轴 (7) 安装在芯组件上。



    图 7g01930820

  1. 将环 (15) 、轴承 (20) 、套筒 (16) 、环 (21) 和导流器 (17) 安装在芯组件上。



    图 8g01930821

    注: 将密封圈 (13) 安装在套筒 (11) 上。 确保密封圈上的开口翻转 180°。

  1. 将密封圈 (13) 安装在套筒 (11) 的槽上。



    图 9g01930822

  1. 将 O 形密封圈 (12) 安装在座圈 (10) 上。

  1. 将套筒 (11) 安装到座圈 (10) 中。

  1. 将座圈 (10) 在芯组件中的涡轮轴上方放置到位。

  1. 使用工具 (C) 安装将座圈固定在芯组件中的挡圈。



    图 10g01930833

  1. 将芯组件在工具 (B) 上放置到位。

  1. 将压缩机叶轮 (5) 在涡轮轴上放置到位。

    注: 安装或拆卸螺母时,请勿对轴施加侧向力。

  1. 安装固定压缩机叶轮的螺母。 使用扭矩扳手和正确尺寸的通用套筒将螺母拧紧至扭矩为 28 ± 3 N·m (21 ± 2 lb ft)。

  1. 将芯组件放置在台钳上。 使用工具 (E) 检查轴的轴向间隙。 磨损的轴向间隙必须为 0.140 ± 0.060 mm (0.0055 ± 0.0024 in)。



    图 11g01930834



    图 12g01930836

  1. 将涡轮壳体安装在工具 (A) 上。 将芯组件 (3) 在涡轮壳体中放置到位。 使用芯组件上的对齐标记作为指导。 将工具 (G) 涂抹在卡箍 (4) 和 (2) 的螺纹上。 安装卡箍 (4) 并拧紧螺栓至扭矩为 13 ± 3 N·m (120 ± 25 lb in)。

  1. 将用于压缩机壳体的 O 形密封圈安装在芯组件上。

  1. 将压缩机壳体 (1) 安装在芯组件上。 使用压缩机壳体和芯组件上的对齐标记作为指导。 安装卡箍 (2) 并拧紧螺栓至扭矩为 13 ± 3 N·m (120 ± 25 lb in)。

  1. 轻敲两个卡箍四周,再拧紧至扭矩为 13 ± 3 N·m (120 ± 25 lb in)。

End By: 安装涡轮增压器。

Caterpillar Information System:

G3304B and G3306B Engines Turbocharger - Disassemble
CX35-P800-C18I and CX35-P800-C27I Petroleum Power Train Packages and CX35-P800 Petroleum Transmission Diagnostic Code List
C9.3 Tier 4 Final Engines Exhaust Gas Valve (NRS)
3508C, 3512C, and 3516C Locomotive Engines CAN Data Link - Test
G3304B and G3306B Engines CAN Data Link - Test
3406E, C-10, C-12, C-15, C-16 Truck Engines Crankshaft End Play - Test
G3304B and G3306B Engines Turbocharger - Install
G3304B and G3306B Engines Turbocharger - Remove
C13 Engine for Combat and Tactical Vehicles Electronic Control Wiring Group
G3304B and G3306B Engines Aftercooler - Install
C13 Engine for Combat and Tactical Vehicles Electronic Control Module
793F and 793F CMD Off-Highway Truck Power Train Position Sensor (Hoist Control)
CX35-P800-C18I and CX35-P800-C27I Petroleum Power Train Packages and CX35-P800 Petroleum Transmission MID 027 - CID 1401 - FMI 03
CX35-P800-C18I and CX35-P800-C27I Petroleum Power Train Packages and CX35-P800 Petroleum Transmission MID 027 - CID 1401 - FMI 05
CX35-P800-C18I and CX35-P800-C27I Petroleum Power Train Packages and CX35-P800 Petroleum Transmission MID 027 - CID 1401 - FMI 06
3500B Generator Set Engines Vibration Damper Guard
G3304B and G3306B Engines Water Temperature Regulator - Remove
G3304B and G3306B Engines Water Temperature Regulator - Install
3508C, 3512C, and 3516C Locomotive Engines Cat Data Link - Test
C9.3 Tier 4 Final Engines General Information
3512C and 3516C Marine Auxiliary and Generator Set Engines Mounting and Dismounting
G3304B and G3306B Engines Water Pump - Remove
2009/06/01 Make Sure that the Generator Set Is Stored Properly {1021, 1404, 7002}
C9.3 Tier 4 Final Engines Basic Engine
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.