Front Suspension (Cylinder) - Disassemble
拆解步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A     | 138-7573     | 连杆支架     | 4     |
B     | 138-7576     | 连杆支架     | 2     |
C     | 1P-0074     | 滑锤拉拔器总成     | 1     |
D     | 8B-7559     | 齿座     | 1     |
开始:
- 拆下前悬挂油缸。
- 拆下充油阀。
- 确保悬架油缸中的氮气已排出。 请参阅专门说明书, SEHS9411, "维修非公路卡车的悬架油缸"。
Show/hide table
为了避免可能造成的人身伤害,在拆解前悬架油缸前卸掉充氮压力。 |
Show/hide table
高压油缸 在释放压力之前,不可拆卸任何零部件,否则会造成人身伤害。 |
- 将前悬架油缸 (1) 放置到适当的夹具上。 前悬架油缸 (1) 的重量约为 3450 kg (7600 lb)。 将适当的容器放置在前悬架油缸 (1) 下方。
Show/hide table
图 1 | g01928258 |
Show/hide table
为了避免可能造成的人身伤害,使用适当的支撑装置来支撑悬架油缸的重量。 不要在没有使用适当的支撑时,而尝试将悬架油缸以末端竖立。 未使用适当的支撑装置可能导致工作区域中的人员受伤甚至死亡。 |
- 拆下螺栓 (3 ) 。 将工具 (A) 和适当的起吊设备固定到缸盖 (2) 上。 使用撬棍以帮助拆下缸盖 (2) 。 缸盖 (2) 的重量约为 140 kg (310 lb)。
Show/hide table
图 2 | g01928315 |
Show/hide table
图 3 | g01928433 |
- 拆下 O 形密封圈 (5) 。 拆下挡圈 (4) 。
Show/hide table
图 4 | g01933413 |
- 将壳体 (6) 中的机油放到适当的容器中以便存放或弃置。
Show/hide table
图 5 | g01285350 |
- 使用工具 (B) 以便拆下活塞杆 (7) 。 活塞杆 (7) 的重量约为 1435 kg (3160 lb)。
Show/hide table
图 6 | g01928453 |
- 水平放置好活塞杆 (7) 。
- 拆下环 (8) 。
Show/hide table
图 7 | g01928464 |
- 将适当的起吊设备固定到活塞 (9) 上。 活塞 (9) 的重量约为 77 kg (170 lb)。
- 拆下工具 (B) 。
- 拆下螺栓 (10) 。
- 拆下活塞 (9) 时,拆下钢珠 (11) 。
Show/hide table
图 8 | g01285380 |
- 拆下螺栓 (12) 。 拆下板 (13) 。
Show/hide table
图 9 | g01285406 |
- 将端块 (14) 向内推,以便拆下护圈 (15) 。
Show/hide table
图 10 | g01285416 |
- 使用工具 (C) 和工具 (D) 以便拆下端块 (14) 。
Show/hide table
图 11 | g01285418 |
- 拆下 O 形密封圈 (16) 。
Show/hide table
图 12 | g01285428 |
- 使用工具 (A) 和适当的起吊设备以便拆下密封管 (17) 。
Show/hide table
图 13 | g01928793 |
- 拆下环 (23) 、O 形密封圈 (22) 、环 (21) 、环 (20) 、O 形密封圈 (19) 和环 (18) 。
Show/hide table
图 14 | g01285446 |
- 拆下环 (24) 。 拆下密封件 (25) 。
Show/hide table
图 15 | g01285455 |
- 将壳体 (6) 放在一旁。 壳体 (6) 的重量约为1665 kg (3670 lb)。
Show/hide table
图 16 | g01285471 |
Show/hide table
图 17 | g01929157 |
- 拆下螺栓和垫圈 (26) 。 拆下护圈 (27) 。 拆下唇形密封 (30) 。 拆下唇型密封 (29) 。 拆下环 (28) 。
Caterpillar Information System:
C9 Marine Engines Configuration Parameters
C9 Marine Engines Diagnostic Flash Code Retrieval
3000 Frame SR5 Electric Power Generation Diode Assembly - Remove and Install
3000 Frame SR5 Electric Power Generation Coupling - Install
C9.3 Industrial Engine Turbocharger
3000 Frame SR5 Electric Power Generation Coupling - Remove
C32 Petroleum Engines General Hazard Information
3512B and 3516B Engines Exhaust Manifold
C9.3 Tier 4 Final Engines Water Lines
C9.3 Engines for Caterpillar Built Machines Relief Valve (Fuel) - Remove and Install
C7.1 Industrial Engine Diesel Particulate Filter - Clean
G3304B and G3306B Engines Exhaust Manifold - Install
797 Off-Highway Truck Front Suspension (Cylinder) - Assemble
The Loss of Fuel Prime in Some C32 Engines{1250, 1280} The Loss of Fuel Prime in Some C32 Engines{1250, 1280}
797F and 797F XQ Off-Highway Trucks Machine Systems Hoist Cylinder - Remove and Install
C9.3 Industrial Engine Turbocharger
2009/07/13 Improved Diagnostic Procedures Are Now Used to Determine Proper Belt Alignment on C9 Marine Engines {1358, 1397}
3500 Engines Exhaust Manifold
3500B Engines Air Shutoff
C9.3 Engines for Caterpillar Built Machines Fuel Manifold - Remove and Install - Return
C13 Engine for Combat and Tactical Vehicles Belt Tensioner
UPS Bearing Type I to G3.5 Conversion{4480} UPS Bearing Type I to G3.5 Conversion{4480}
Instructions For Converting Uninterruptible Power Supplys With Hall Effect Probes To The G3.5 Load Cell{4480} Instructions For Converting Uninterruptible Power Supplys With Hall Effect Probes To The G3.5 Load Cell{4480}
2009/05/25 Correction to Schematics for the Control Group {1408}