Exhaust Manifold - Remove
拆卸步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件说明     | 数量     |
A     | 138-7575     | 连杆支架     | 2     |
开始:
- 拆下涡轮增压器。
- 拆下电子控制模块。
Show/hide table
热的冷却液、蒸汽和碱会造成人身伤害。 在工作温度下,发动机冷却液是热的而且处在压力下。 散热器和所有到加热器的管路或发动机中都有热的冷却液或蒸汽。 与它们的任何接触都会造成严重烫伤。 只有当发动机停机且冷却系统压力盖已经冷却到可以徒手触摸时,再慢慢拆下冷却系统压力盖以释放压力。 不要试图在冷却液还热的时候去拧紧软管接头,软管会脱落而造成灼伤。 警告:冷却系统的冷却液添加剂含碱。 应避免它与皮肤和眼睛接触。 |
注: 在所有管路、软管、导线和管子上做出识别标记以便安装。 插接所有管路、软管和管子。 这将有助于防止液体泄漏和污染物进入系统。
- 排空冷却系统中的冷却液。 请参阅操作和保养手册, "冷却系统冷却液 - 更换"。
- 将管组件 (1) 从排气歧管上断开。
Show/hide table
图 1 | g01925099 |
- 拆下火花塞导线。
- 拆下将变压器 (3) 固定在位的螺栓 (2) 。
- 将变压器 (3) 和线束组件作为一个整体拆下。
- 断开管组件 (4) 。
Show/hide table
图 2 | g01925101 |
- 松开卡箍组件并断开软管 (5) 。
- 拆下将管组件 (6) 固定在位的螺栓。 将管组件 (6) 、隔套、密封垫和 O 形密封圈从排气歧管上拆下。
- 将工具 (A) 和适当的起吊设备连接到排气歧管 (7) 上。 排气歧管 (7) 的重量约为 29 kg (65 lb)。
- 拆下螺栓 (8) 、排气歧管 (7) 和密封垫。
Caterpillar Information System:
C32 Petroleum Engines Monitoring System
C9 Engine Monitoring System
C13 Engine for Caterpillar Built Machines Accessory Drive - Remove and Install - Brackets and Pulleys
G3304B and G3306B Engines Spark Plug Adapter - Remove and Install
G3304B and G3306B Engines Spark Plugs - Remove and Install
C7 Petroleum Engine Plate Locations and Film Locations
G3304B and G3306B Engines Carburetor - Install
C32 Petroleum Engines Installation Environment
C7 Petroleum Engine Installation Environment
C13 Engine for Caterpillar Built Machines Belt Tensioner - Remove and Install
G3304B and G3306B Engines Indicator Lamp - Test
C7.1 Industrial Engine and Generator Set 5 Volt Sensor Supply Circuit - Test
C7 Engines for Combat and Tactical Vehicles Safety Messages
2009/06/22 Fuel Injection Pump Latch Valve {1251}
3500B Engines for Caterpillar Built Power Modules Fuel Injector Mechanism
C9.3 Engines for Caterpillar Built Machines Fuel Manifold (Rail) - Remove and Install
2009/06/08 The Packaging Consist of the C9 Genset Has Been Changed {1000, 1021, 7002}
C7 Industrial Engines Turbocharger
C13 Engine for Combat and Tactical Vehicles Turbocharger
G3304B and G3306B Engines Exhaust Manifold - Install
C7.1 Industrial Engine Diesel Particulate Filter - Clean
C9.3 Engines for Caterpillar Built Machines Relief Valve (Fuel) - Remove and Install
C9.3 Tier 4 Final Engines Water Lines
3512B and 3516B Engines Exhaust Manifold