Oversized Injector Sleeves for Remanufactured Cylinder Heads On Medium Sized Engines{1100, 1101, 1125} Caterpillar


Oversized Injector Sleeves for Remanufactured Cylinder Heads On Medium Sized Engines{1100, 1101, 1125}

Usage:

627F 1DL
Machine Engine:
3406E (S/N: 9AP1-UP; BKN1-UP; BET1-UP)
3456 (S/N: 7RC1-UP; BNT1-UP; BLC1-UP)
C15 (S/N: LHX1-UP)
C-15 (S/N: A3A1-UP)
C-16 (S/N: GDA1-UP)
C18 (S/N: RHX1-UP)
On-highway Truck Engine:
3406E (S/N: 5EK1-UP; 1MM1-UP; 2WS1-UP; 5DS1-UP; 6TS1-UP; 1LW1-UP)
C-15 (S/N: C2A1-UP; EGH1-UP; MBN1-UP; 6NZ1-UP; 9NZ1-UP)
C-16 (S/N: W1A1-UP; 7CZ1-UP)
C-18 (S/N: CJP1-UP; MDP1-UP; MEP1-UP)
C15 (S/N: KRA1-UP; ZKA1-UP; TRB1-UP; JEP1-UP; MHP1-UP; SDP1-UP; B5R1-UP; BXS1-UP; MXS1-UP; NXS1-UP; RKS1-UP)
C18 (S/N: ZKB1-UP)
Generator Set:
3406E (S/N: 9NN1-UP; 8AZ1-UP)
3456 (S/N: BGA1-UP; CCB1-UP; BLC1-UP; EPE1-UP; C1G1-UP; C3G1-UP; C4G1-UP; CAH1-UP; GHJ1-UP; C2T1-UP; CBX1-UP; 9BZ1-UP)
C15 (S/N: PEC1-UP; C5E1-UP; STG1-UP; C5H1-UP; C5L1-UP; NKL1-UP; PET1-UP; X4R1-UP; CYY1-UP)
C18 (S/N: C6C1-UP; G4C1-UP; STD1-UP; DKE1-UP; PEE1-UP; PEJ1-UP; NKK1-UP; CYL1-UP; STM1-UP; MGS1-UP; EKW1-UP)
Industrial Engine:
3406E (S/N: 6BR1-UP)
3456 (S/N: 3LW1-UP)
C-15 (S/N: BEM1-UP)
C-16 (S/N: BFM1-UP)
C15 (S/N: JRE1-UP; JAS1-UP)
C18 (S/N: EJG1-UP; JDA1-UP; WJH1-UP)
Marine Engine:
3406E (S/N: 9WR1-UP)
C15 (S/N: RLA1-UP)
C18 (S/N: WKB1-UP; PLE1-UP; CKH1-UP; C1J1-UP; CYN1-UP; GEN1-UP; GES1-UP; KJT1-UP; JKX1-UP; NAX1-UP; NAY1-UP; J2K1-UP; T2P1-UP)
Petroleum Engine:
C-15 (S/N: Z2C1-UP)
C15 (S/N: JDK1-UP)
C18 (S/N: WJW1-UP)
Power Module:
C18 (S/N: X6X1-UP)



Illustration 1g02004767

(1) Ring for Identification

(2) 228-7094 O-Ring Seal

(3) 345-3399 Injector Sleeve

An oversized injector sleeve will be introduced in order to improve the life cycle of the cylinder heads. The new sleeve has an oversized outside diameter, which does not allow the injector sleeve to fit the standard bore. The oversized sleeve will have an added ring that is located around the middle of the insert for identification. Also, the new sleeve will require a larger bottom O-ring. Refer to Illustration 1.




Illustration 2g02004793

(4) Identification mark

The remanufactured cylinder head has an identification mark that is located on the top of the cylinder head. This mark indicates the cylinders that have the oversized inserts.

Caterpillar Information System:

C9.3 Industrial Engine Air Compressor
C13 Engines for Caterpillar Built Machines Temperature Sensor (DPF) - Remove and Install - Clean Emissions Module
C7.1 Industrial Engine and Generator Set Indicator Lamp Circuit - Test
C13 Engines for Caterpillar Built Machines Catalyst - Remove and Install - Diesel Oxidation Catalyst, Clean Emissions Module
C7.1 Industrial Engine and Generator Set Idle Validation Switch Circuit - Test
C13 Engines for Caterpillar Built Machines Diesel Particulate Filter - Remove and Install - Clean Emissions Module
C13 Engines for Caterpillar Built Machines Soot Antenna - Remove and Install
C27 and C32 Engines for Caterpillar Built Machines Atmospheric Pressure Sensor
C13, C15, and C18 Tier 4 Final Engines Boost Pressure Sensor
C13 Engines for Caterpillar Built Machines Flame Detection Temperature Sensor - Remove and Install - Clean Emissions Module
C18 Marine Engines Engine Speed/Timing Sensor - Clean/Inspect
C32 Marine Engine Pinion Clearance - Adjust
793F and 797F Off-Highway Trucks Power Train Electronic Control System Retarder Is Aggressive
2009/10/29 A New Bowl for the Fuel/Water Separator Is Used {1261, 1263}
2009/10/29 A New Bowl for the Fuel/Water Separator Is Available {1261, 1263}
C9.3 Tier 4 Final Engines Crankcase Pressure Sensor
3508C, 3512C, and 3516C Locomotive Engines Acceleration Is Poor or Throttle Response Is Poor
Improved Method for Installing the Actual Gear Position Sensor {1439, 3061} Improved Method for Installing the Actual Gear Position Sensor {1439, 3061}
797 and 797B Off-Highway Truck/Tractor Engine Air Filter Secondary Element - Replace
C9.3 Engines for Caterpillar Built Machines Exhaust Manifold - Remove and Install
C9.3 Tier 4 Final Engines Water Temperature Regulator
C13 Engines for Caterpillar Built Machines Muffler - Remove and Install - Clean Emissions Module
C9.3 Tier 4 Interim Engines Injector Solenoid - Test
C9.3 Engines for Caterpillar Built Machines Fuel Injection Pump - Test
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.