3500B Engines and 776D, 777D, 784C, 785C, 789C, 793C and 793D Off-Highway Truck/Tractors Caterpillar


Electric Starting Motor

Usage:

785C 1HW


图 1g02617582

表 1
6V-0889 电起动马达总成和 6V-0513 电起动马达总成的技术规格 
项目  数量  零件  技术规格说明 
6V-8188 螺母  拧紧至扭矩为 30.5 ± 3.5 N·m (269.9 ± 31.0 lb in)。 
4B-2049 螺母  拧紧扭矩至 2.25 ± 0.25 N·m (19.91 ± 2.21 lb in)。 
4B-2049 螺母  开关端子必须用热收缩管绝缘。 不要使用模压端子。
拧紧扭矩至 2.25 ± 0.25 N·m (19.91 ± 2.21 lb in)。 
6V-8188 螺母  拧紧至扭矩为 30.5 ± 3.5 N·m (269.9 ± 31.0 lb in)。 
6V-8188 螺母  蓄电池端子螺母最多可使用三条电缆或导线端子。 两个电缆端子最高不低于 0 AWG。
拧紧至扭矩为 30.5 ± 3.5 N·m (269.9 ± 31.0 lb in)。 
6V-8188 螺母  拧紧至扭矩为 30.5 ± 3.5 N·m (269.9 ± 31.0 lb in)。 
小齿轮和壳体之间的间隙为 9.1 mm (0.36 in)。 
20 V 和 25° C (77° F) 时的吸合电流为 49.3 ± 3.3 安培。 
20 V 和 25° C (77° F) 时的保持电流最大为 6.8 安培。
当从小齿轮端观看电起动马达时,马达顺时针旋转。 

Caterpillar Information System:

C9.3 Engines for Caterpillar Built Machines Service Information Report
2009/04/13 Do Not Adjust the Desired Speed During a Normal Stop for a Gas Engine with an ADEM 3 Control Module {1901, 1920}
C15 and C18 Industrial Engines Muffler - Remove and Install - Clean Emissions Module
C13 Engine for Caterpillar Built Machines Atmospheric Pressure Sensor - Remove and Install
3408E and 3412E Engines for Caterpillar Built Machines Pressure Sensor - Calibrate
C15 and C18 Industrial Engines Exhaust Combustion Manifold (ARD) - Remove and Install
C13 Engines for Caterpillar Built Machines Inlet Manifold Temperature Sensor - Remove and Install
C13 Engine for Caterpillar Built Machines Boost Pressure Sensor - Remove and Install
C13 Engine for Caterpillar Built Machines Fuel Temperature Sensor - Remove and Install
C13 Engine for Caterpillar Built Machines Fuel Pressure Sensor - Remove and Install
C13 Tier 4 Final Engines Fuel System
C13 Engine for Caterpillar Built Machines Crankcase Pressure Sensor - Remove and Install
C7.1 Industrial Engine and Generator Set Engine Does Not Crank
C7.1 Industrial Engine Engine Oil and Filter - Change
C7.1 Industrial Engine Belt Tensioner - Inspect
C9.3 Engines for Caterpillar Built Machines Engine Monitoring System
C7.1 Industrial Engine and Generator Set Engine Shutdown Occurs Intermittently
C7.1 Industrial Engine and Generator Set Oil Pressure Is Low
C7.1 Industrial Engine and Generator Set Engine Has Mechanical Noise (Knock)
C7.1 Industrial Engine and Generator Set Cylinder Is Noisy
C18 Power Module Maintenance Interval Schedule
C18 Power Module Maintenance Interval Schedule - Standby
C15 and C18 Industrial Engines Diesel Particulate Filter - Remove and Install - Clean Emissions Module
C7.1 Industrial Engine and Generator Set Valve Lash Is Excessive
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.