584 and 584HD Forwarders Machine Preheater Caterpillar


Operational Flow Chart

Usage:

584HD 109

Table 1
    Starting     Running     SHUT DOWN PHASE    
Operating Mode     System Check     Preheat     Ignition     Preheat 2nd Attempt     Ignition 2nd Attempt     Controlled Heating     After Glow     Cool Down     Off or Standby    
Coolant Pump     OFF     ON     ON     ON     ON     ON     ON     ON     OFF
(ON in Standby)    
Combustion Air Fan     ON
Momentary    
ON     ON     OFF     ON     ON     ON     ON     OFF    
Glow Pin     OFF     ON     ON     ON     ON     OFF     ON     OFF     OFF    
Fuel Metering Pump     OFF     OFF     ON     OFF     ON     ON     OFF     OFF     OFF    
Operating indicator Light     ON     ON     ON     ON     ON     ON     OFF     OFF     OFF    
Fan for the Vehicle     ON
Momentary    
OFF     OFF     OFF     OFF     ON     ON     ON     OFF    
Flame Monitor     ON     ON     ON     ON     ON     OFF     OFF     OFF     OFF    
Time     1-3 sec.     60 sec. to 140 sec.     <90 sec.     80 sec.     <90 sec.         20 sec.     2.5 min.        

Note: If the coolant temperature exceeds 86 °C (187 °F) during the controlled heating cycle the machine preheater will shutdown. The machine preheater will automatically restart in the high heat mode once the coolant temperature reaches 75 °C (167 °F).

Caterpillar Information System:

CP44 and CS44 Vibratory Soil Compactors Parking Brake - Check
Installation of the 330-0824 Control Arrangement (Variable Pitch Fan) (Kit){1356} Installation of the 330-0824 Control Arrangement (Variable Pitch Fan) (Kit){1356}
CB54, CB54 XW and CB64 Vibratory Compactors Propel System Piston Pump (Propel) (Swashplate Angle) - Check
120K and 120K Series 2 Motor Graders Machine Systems Fuel Tank - Install
120K and 120K Series 2 Motor Graders Machine Systems Fuel Tank - Remove
CP44 and CS44 Vibratory Soil Compactors Steering Column Spline (HMU Steering) - Lubricate
584 and 584HD Forwarders Machine Preheater Heater System Electrical Schematic
416E Backhoe Loader Hydraulic and Steering System Ride Control System
2009/02/16 Disposable Paper Air Filters Require Protection {1051, 1054}
Work Tool (Custom) <B>338-0312</B> Log and Lumber Fork Maintenance Interval Schedule
795F AC and 795F AC XQ Off-Highway Trucks Air Filter Element (Inverter Cabinet) - Clean/Replace - Metal Sand Filters
143H and 163H Motor Graders All Wheel Drive All Wheel Drive System
416E Backhoe Loader Hydraulic and Steering System Ride Control Accumulator - Test and Charge
CP44 and CS44 Vibratory Soil Compactors Fuel System - Prime
2009/02/02 A New Rocker Arm Assembly is Available {1123}
795F AC and 795F AC XQ Off-Highway Truck Steering System Solenoid Valve and Manifold (Blower Fan, Final Drive Lubrication, Steering)
2011/09/12 A New Rocker Arm Assembly Is Available {1123}
AccuGrade&reg; (CD610) Hydraulic System
Work Tool (Custom) <B>338-0312</B> Log and Lumber Fork Hydraulic Fittings - Inspect
2009/02/09 Improvement to the Oil Pressure Switch {7400, 7421}
2009/03/30 Introduction of a New Fuel Filter Base {1260, 1261}
2009/03/30 Introduction of a New Fuel Filter Base {1260, 1261}
CP44 and CS44 Vibratory Soil Compactors Fuel System Primary Filter (Water Separator) - Replace
CP44 and CS44 Vibratory Soil Compactors Fuel System Secondary Filter - Replace
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.