Auxiliary Water Pump - Disassemble - Auxiliary Pump (Type 2)
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件说明 | 数量 |
A | 242-9955 | 拉拔器 (两爪) | 1 |
B | 193-8094 | 花键套筒 | 1 |
C | 1P-0510 | 冲头总成 | 1 |
D | 5P-4758 | 挡圈钳组件 | 1 |
E | 280-2059 | 活动扳手组件 | 1 |
F | 8T-0276 | 螺栓 | 2 |
G | 8H-0663 | 轴承拉拔器总成 | 1 |
开始:
- 拆卸辅助水泵。 参考拆解与组装, "辅助水泵 - 拆卸"。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 将软管组件 (1)、单向阀 (2) 和密封垫从辅助水泵上拆下。
Show/hide table
图 2 g01644824 Show/hide table弹簧加压的零件和/或盖板可能导致人身伤害。
拆卸盖板时弹簧力将被释放。
松动螺栓时做好准备把持住弹簧加载的盖板。
- 利用工具 (D) 将护圈 (3) 从单向阀 (2) 的阀体上拆下。
- 将弹簧 (4) 和圆盘 (5) 从单向阀 (2) 的阀体上拆下。
注: 如果软管组件泄漏,必须更换整个软管组件。
Show/hide table
图 1 | g01644713 |
- 拆下螺栓 (6) 和盖 (7)。 将 O 形密封圈 (8) 从盖 (7) 上拆下。
Show/hide table
图 4 g01645415 - 拆下配流盘 (9)。
Show/hide table
图 5 g01645633 - 利用工具 (B) 固定驱动轴的端部。 拆下螺栓 (10)、止推垫圈 (11) 和 O 形密封圈。
Show/hide table
图 6 g01645634 注: 拆卸中,记下锁环的方位。
- 将辅助水泵竖直定位到适当的支座上。 确保轴组件得到支撑。 利用工具 (C) 和适当的手锤敲打叶轮 (13)。 从而使锁环 (12) 上的锥面松动。 拆下锁环 (12)、叶轮 (13)、环 (14)、O 形密封圈 (15) 和配流盘 (16)。
Show/hide table
图 7 g01645635 - 拆下螺栓 (17)。 将螺栓 (17) 作为顶出螺栓拆下泵体 (18)。 将 O 形密封圈 (19) 从泵体 (18) 上拆下。
Show/hide table
图 8 g01646414 - 利用工具 (A) 和工具 (C) 拆下叶轮 (20)。
Show/hide table
图 9 g01646456 - 将密封组件 (21) 的旋转段从泵体上拆下。
Show/hide table
图 10 g01646457 - 将辅助水泵竖直放到适当的支座上,如图所示。 将螺栓 (23) 从轴承壳体 (22) 上拆下。 在孔 (24) 中利用工具 (F) 将轴承壳体 (22) 从泵体上分离。
Show/hide table
图 11 g01721917 - 利用工具 (C) 和适当的压具将密封组件 (21) 的固定段从泵体上拆下。
Show/hide table
图 12 g01646635 - 利用工具 (D) 将挡圈 (25) 从轴承壳体 (22) 上拆下。
Show/hide table
图 13 g01646637 - 将固定螺钉 (27) 从密封套环 (28) 上拆下。 使用适当的压具将轴组件 (26) 从轴承壳体 (22) 上拆下。 拆下轴组件 (26)、密封套环 (28) 和 O 形密封圈。
Show/hide table
图 14 g01646638 Show/hide table图 15 g01723074 - 利用工具 (B) 和工具 (E) 将锁紧螺母 (29) 从轴组件 (26) 上拆下。
- 利用工具 (G) 和适当的压具将轴承 (30) 从轴组件 (26) 上拆下。
Show/hide table
图 16 g01646918 - 将油封 (31) 从轴承壳体 (22) 上拆下。 利用工具 (D) 拆下挡圈 (32)。 将滚柱轴承 (33) 和轴承座圈 (34) 从轴承壳体 (22) 上拆下。 检查供油节流孔上 O 形密封圈的状态。 必要时,应更换 O 形密封圈。
Show/hide table
图 3 | g01645413 |
Caterpillar Information System:
TH48-E70 Petroleum Transmission Safety Messages
An Updated Troubleshooting Procedure for the Caterpillar Regeneration System Is Available{1050} An Updated Troubleshooting Procedure for the Caterpillar Regeneration System Is Available{1050}
C18 Power Module Winding - Test
3412, 3412C, and 3412E Generator Set Engines Fuel Rack Solenoid - Test
3512B Engine Instrument Panel
2008/09/08 Replace the Connecting Rod Bearings According to the Operation and Maintenance Manual {1219, 1225}
3500 Generator Sets Generator Load - Check
C4.4 Generator Set Engines Starting Aid (Glow Plug) Relay Circuit - Test
Troubleshooting a Loss of Combustion with the Aftertreatment Regeneration Device (ARD) {1088} Troubleshooting a Loss of Combustion with the Aftertreatment Regeneration Device (ARD) {1088}
2008/09/29 Procedure to Repair a Service Meter that Runs Constantly {1426, 4462}
3500 Generator Sets Engine Air Cleaner Service Indicator - Inspect
Proper Plugging of the 315-1391 Crankshaft {1202} Proper Plugging of the 315-1391 Crankshaft {1202}
G3500J Engines Configuration Parameters
3512B Generator Set Engine Event Codes
3500B Engines Auxiliary Water Pump - Assemble - Auxiliary Pump (Type 2)
3412, 3412C, and 3412E Generator Set Engines Speed Control - Test
3512B Generator Set Engine Configuration Parameters
3412, 3412C, and 3412E Generator Set Engines Fuel Rack Position Sensor - Calibrate
Procedure for Powering the Battery Charger Continuously{751B} Procedure for Powering the Battery Charger Continuously{751B}
Clean Gas Induction (CGI) Line Upgrade{1061, 1087, 108N} Clean Gas Induction (CGI) Line Upgrade{1061, 1087, 108N}
3412, 3412C, and 3412E Generator Set Engines Speed Control (PWM) - Test
G3600 Engines Welding Precaution
2008/10/01 Diagnostic Code Occurring on C11 and C13 On-Highway Engines {1901, 1920}
Filtration Procedure For Cold Planer Hydraulic Oil {0680, 0738, 0768, 5050, 5056} Filtration Procedure For Cold Planer Hydraulic Oil {0680, 0738, 0768, 5050, 5056}