Torque Converter - Install
安装步骤
Show/hide table
| 所需工具 | |||
| 工具 | 零件号 | 零件描述 | 数量 |
| A | 1U-9200 | 操纵杆滚轮起重机 | 1 |
| B | 138-7575 | 连杆支架 | 4 |
| C | 140-7742 | 套环 | 2 |
| E | 1U-6396 | O 形圈组装固定胶 | 1 |
| F | 导向螺柱 3/4 - 10 x 6 in | 2 | |
- 安装 O 形密封圈 (8) 。 安装密封圈 (7) 。 将工具 (E) 涂抹到所密封的孔中。
Show/hide table
 | |
| 图 1 | g01607475 |
- 将工具 (B) 和适当的起吊设备固定到变矩器组件 (5) 上。 变矩器组件 (5) 的重量约为 340 kg (750 lb)。 固定工具 (F) ，以引导变矩器组件 (5) 就位。 定位变矩器组件 (5) 。 拆下工具 (F) ，然后安装螺栓 (6) 。 拆下工具 (B) 。 图中未显示工具 (F) 。
Show/hide table
 | |
| 图 2 | g01192915 |
Show/hide table
 | |
| 图 3 | g01192918 |
- 利用工具 (B) 和适当的起吊设备定位轮毂 (4) 。 轮毂 (4) 的重量约为 35 kg (75 lb)。 安装螺栓 (3) 。 拆下工具 (B) 。 拆下工具 (D) 。
Show/hide table
 | |
| 图 4 | g01192896 |
Show/hide table
 | |
| 图 5 | g01193591 |
- 将工具 (A) 、工具 (B) 、工具 (C) 和适当的起吊设备固定到变矩器壳体组件 (2) 上。 变矩器壳体 (2) 的重量大约为 615 kg (1350 lb)。 翻转变矩器壳体组件 (2) 。
Show/hide table
 | |
| 图 6 | g01192873 |
- 安装管组件 (1) 。
Show/hide table
 | |
| 图 7 | g01192865 |
End By:
- 安装分动器行星齿轮 （增速）。 请参阅 拆解和组装, "分动器行星齿轮（增速）- 安装"。
- 安装分动器。 请参阅 拆解和组装, "分动器 - 安装"。
Caterpillar Information System:
3508C, 3512C and 3516C Locomotive Engines Prelube Pressure Switch
TH48-E80 Oil/Gas Transmission Torque Converter - Remove
C27 and C32 Industrial and Petroleum Engines Engine Oil Pan
C27 and C32 Industrial and Petroleum Engines Engine Oil Pan
C27 and C32 Industrial and Petroleum Engines Engine Oil Pan
3512C Engine and 785D Off-Highway Truck/Tractors ECM - Replace
3512C Petroleum Engines Intake Manifold Air Temperature Is High
3512B and 3516B Engines Piston and Rings - Two-Piece Piston
C18 Generator set and C18 Marine Engines Aftercooler - Install
C18 Generator set and C18 Marine Engines Aftercooler - Remove
C18 Marine Generator Set Engine Valve Lash - Inspect/Adjust
3412E and C30 Marine Engines System Pressure Release
2008/09/08 Procedure for Crankshafts that will not Rotate after Installation during a Rebuild {1000, 1202}
C18 Generator set and C18 Marine Engines Vibration Damper and Pulley - Remove and Install
2009/04/20 An Improved Radio Power Converter is used on Excavators. {1408, 1421, 7338}
C27 and C32 Industrial and Petroleum Engines Vibration Damper and Pulley
3500B Locomotive Engines Cylinder Head Valves
3512B Generator Set Engine Pressure Contactor
3512B Generator Set Engine Pressure Transducer
Specifications for Inspection of Driveline Fasteners {3030, 3101, 3159, 3253, 3258, 3278, 4050} Specifications for Inspection of Driveline Fasteners {3030, 3101, 3159, 3253, 3258, 3278, 4050}
G3412C, G3508, G3512 and G3516 Engines Status Control Module General Information
G3412C, G3508, G3512 and G3516 Engines Status Control Module Service Tools
G3412C, G3508, G3512 and G3516 Engines Status Control Module Symptom Troubleshooting
G3412C, G3508, G3512 and G3516 Engines Status Control Module Engine Cranks but Does Not Start