MID 039 - CID 1178 - FMI 08
产生此代码的情况:
Show/hide table
图 1 | g01521226 |
动臂过载压力传感器示意图 |
在 ECM 读取到压力传感器(导线 E446-PK(粉))的信号无效时会记录该诊断代码。
可能由于下列原因产生该诊断代码:
- 导线 E446-PK(粉) 短路。
- 传感器安装不正确。
- 传感器出故障。
- ECM 出现故障。 这不太可能。
注: 机器 ECM 配备有作为自诊断检查的 LED 指示灯。 在钥匙起动开关接通的情况下,可通过 ECM 指示灯确定以下状况:·如果所有 LED 指示灯均熄灭,则不会向机器 ECM 提供电压。 检查 ECM 的供电。 · 如果黄色 LED 闪烁,说明通信错误发生在 "CAN" 数据链路电路中。 · 如果黄色 LED 稳定亮起,则机器 ECM 软件可能缺失/未加载。 · 如果红色 LED 闪烁,则机器 ECM 有故障,并且可能需要更换。
注: 确保传感器的诊断代码为激活状态。
测试步骤 1. 检查传感器。
- 将断路开关和钥匙起动开关转到接通位置。
- 确保诊断代码存在。
- 观察诊断代码的状态。 然后从传感器上断开机器线束。
预期结果:
如果传感器不是该诊断代码的原因,该诊断代码将仍然存在。 如果传感器出故障,该诊断代码将不再存在。
结果:
- 确定 - 诊断编码仍然存在。 传感器没有故障。 可能是机器线束或 ECM 出故障。 转至测试步骤 2。
- 异常 - 诊断编码不再存在。 机器线束正常,并且 ECM 工作正常。 传感器出故障。
修复: 更换传感器。 确认使用新传感器后故障得到排除。
停止
测试步骤 2. 检查线束有无短路。
- 将钥匙起动开关和断路开关转到断开位置。
- 机器线束仍保持从传感器上断开的状态。
- 从 ECM 上断开接头 J1 和 J2。
- 在 ECM 的接头 J1 上,测量触点 J1-37(导线 E446-PK(粉))与所有其它 J1 和 J2 触点之间的电阻。
预期结果:
电阻应大于 5 欧姆。
结果:
- 是 - 各电阻测量值都大于 5 欧姆。 线束正常。 ECM 出现故障。
修复: ECM 不太可能会出现故障。 退出本步骤,然后重新执行该诊断代码步骤。 如果没有找到该诊断代码的原因,则应更换 ECM。 参见测试和调整, "电子控制模块(ECM)- 更换 "。
停止
- 否 - 每次测量的电阻都不大于 5 欧姆。 线束中存在短路。
修复: 信号电路(导线 E446-PK(粉))与电阻测量值低的电路之间存在短路。 修理或更换线束。
停止
Caterpillar Information System:
345D, 349D and 349D2 Excavators and 345D MHPU, 349D MHPU and 349D2 MHPU Mobile Hydraulic Power Units Machine Electronic Control System MID 039 - CID 1178 - FMI 04
C7 PETROLEUM Petroleum Engine Fuel Pressure Sensor - Remove and Install
TH31-C9I, TH31-C9P, TH31-C9T, TH35-C13I, TH35-C13T, TH35-C15I and TH35-C15T Petroleum Power Train Packages and TH31-E61 and TH35-E81 Petroleum Transmissions Transmission Transmission Planetary - TH35 Drop Box
345D, 349D and 349D2 Excavators and 345D MHPU, 349D MHPU and 349D2 MHPU Mobile Hydraulic Power Units Machine Electronic Control System MID 039 - CID 1178 - FMI 03
Replacement of Incorrect Lifter Assemblies on 3116 Engines{1209} Replacement of Incorrect Lifter Assemblies on 3116 Engines{1209}
345D, 349D and 349D2 Excavators and 345D MHPU, 349D MHPU and 349D2 MHPU Mobile Hydraulic Power Units Machine Electronic Control System MID 039 - CID 1160 - FMI 06
345D, 349D and 349D2 Excavators and 345D MHPU, 349D MHPU and 349D2 MHPU Mobile Hydraulic Power Units Machine Electronic Control System MID 039 - CID 1130 - FMI 03
2008/05/19 Improved Fuel Injector {1251, 1254, 1290, 1713}
345D, 349D and 349D2 Excavators and 345D MHPU, 349D MHPU and 349D2 MHPU Mobile Hydraulic Power Units Machine Electronic Control System MID 039 - CID 0735 - FMI 06
C15 Petroleum Generator Set Engines Fuel Pressure Sensor
Product Link PL321 May Accumulate 24 Hours Daily{7606} Product Link PL321 May Accumulate 24 Hours Daily{7606}
C27 and C32 Industrial Engines Configuration Parameters
C6.6 Marine Generator Set Fire Prevention and Explosion Prevention
Removing and Installing Bushings and Pressure Plates in Hydraulic Gear Pumps {5073} Removing and Installing Bushings and Pressure Plates in Hydraulic Gear Pumps {5073}
345D, 349D and 349D2 Excavators and 345D MHPU, 349D MHPU and 349D2 MHPU Mobile Hydraulic Power Units Machine Electronic Control System MID 039 - CID 1615 - FMI 03
C7 PETROLEUM Petroleum Engine Injection Actuation Pressure Sensor - Remove and Install
345D, 349D and 349D2 Excavators and 345D MHPU, 349D MHPU and 349D2 MHPU Mobile Hydraulic Power Units Machine Electronic Control System MID 039 - CID 1615 - FMI 05
345D, 349D and 349D2 Excavators and 345D MHPU, 349D MHPU and 349D2 MHPU Mobile Hydraulic Power Units Machine Electronic Control System MID 039 - CID 1615 - FMI 06
345D, 349D and 349D2 Excavators and 345D MHPU, 349D MHPU and 349D2 MHPU Mobile Hydraulic Power Units Machine Electronic Control System MID 039 - CID 1661 - FMI 03
345D, 349D and 349D2 Excavators and 345D MHPU, 349D MHPU and 349D2 MHPU Mobile Hydraulic Power Units Machine Electronic Control System MID 039 - CID 1661 - FMI 05
C7 PETROLEUM Petroleum Engine Speed/Timing Sensor - Remove and Install
345D, 349D and 349D2 Excavators and 345D MHPU, 349D MHPU and 349D2 MHPU Mobile Hydraulic Power Units Machine Electronic Control System MID 039 - CID 1661 - FMI 06
345D, 349D and 349D2 Excavators and 345D MHPU, 349D MHPU and 349D2 MHPU Mobile Hydraulic Power Units Machine Electronic Control System MID 039 - CID 1931 - FMI 03
G3304 and G3306 Engines Engine Speed Sensor