Cylinder Head
Show/hide table
| |
| 图 1 | g02548868 |
|
典型示例 | |
Show/hide table
| 技术规格，适用于 263-5054 缸盖总成和 223-7263 缸盖 | |||
|---|---|---|---|
| 项目 | 数量 | 零件 | 技术规格说明 |
| - | - | - | 以下螺栓的长度为 以下螺栓的长度为 将黑色 Loctite 石墨-50 涂覆到螺栓螺纹上和硬垫圈的两侧。 按照下列步骤拧紧缸盖的螺栓： 按照数字顺序依次拧紧 1 到 26 号螺栓至扭矩为 按照数字顺序依次拧紧 1 到 26 号螺栓至扭矩为 再次按照数字顺序依次拧紧 1 到 26 号螺栓至扭矩为 缸盖的平面度应在总共 |
Show/hide table
| |
| 图 2 | g02548900 |
Show/hide table
| 项目 | 数量 | 零件 | 技术规格说明 |
|---|---|---|---|
| A | - | - | 缸盖厚度：
新缸盖的厚度为 旧缸盖的最小厚度为 |
Show/hide table
| |
| 图 3 | g02548907 |
|
(1) 套筒轴承接头
(2) 油道 (3) 机油孔 (4) 套筒轴承 | |
Show/hide table
| 注意 |
|---|
|
必须把凸轮轴轴承安装到正确位置。 不这样做的话可能导致发动机损坏。 |
Show/hide table
| |
| 图 4 | g02548916 |
Show/hide table
| 项目 | 数量 | 零件 | 技术规格说明 |
|---|---|---|---|
| B | - | - | 套筒轴承接头的方位为水平面以上 20 ± 5 度 |
| C | - | - | 凸轮轴套筒轴承的孔径为 |
Show/hide table
| |
| 图 5 | g02548921 |
Show/hide table
| 项目 | 数量 | 零件 | 技术规格说明 |
|---|---|---|---|
| 4 | 7 | 216-5582 衬套 | 套筒轴承的安装深度是很重要的。 将套筒轴承安装到以下深度：
尺寸 (D)： 尺寸 (E)： 尺寸 (F)： 尺寸 (G)： 尺寸 (H)： 尺寸 (J)： 尺寸 (K)： |
Show/hide table
| |
| 图 6 | g01623607 |
Show/hide table
| 项目 | 数量 | 零件 | 技术规格说明 |
|---|---|---|---|
| 5 | - | - | 组装前，将 4C-9506 固定胶涂抹在六个喷油器套筒的下端压装直径上。
将喷油器套筒压到面 (6) 的底部。 |
| V | - | - | 碗形塞的安装深度为 |
Caterpillar Information System:
2008/04/28 Improved Turbocharger {1052, 1053}
C6.6 Marine Generator Set Safety Messages
Installation and Operation of the Exhaust Monitor Used in All Diesel Particulate Filter (DPF) Retrofit Emissions Applications{1091, 1408, 7490, 7498} Installation and Operation of the Exhaust Monitor Used in All Diesel Particulate Filter (DPF) Retrofit Emissions Applications{1091, 1408, 7490, 7498}
Rebuilding Front Axles, Spindle Housings, Leaning Arms, and Lean Bars {4313, 5211, 5225} Rebuilding Front Axles, Spindle Housings, Leaning Arms, and Lean Bars {4313, 5211, 5225}
C175-16 and C175-20 Generator Set Engines Lubrication System Operation
Air Conditioning and Heating R134a for All Caterpillar Machines Heater Performance - Test
Air Conditioning and Heating R134a for All Caterpillar Machines Compressor Protection System - Test
Air Conditioning and Heating R134a for All Caterpillar Machines Machine Preparation for Disassembly and Assembly
Air Conditioning and Heating R134a for All Caterpillar Machines Machine Preparation for Testing and Adjusting
3512B Petroleum Engine Maintenance Recommendations
Testing the Refrigerant Compressor Protection Module{1408, 1802} Testing the Refrigerant Compressor Protection Module{1408, 1802}
345D, 349D and 349D2 Excavators and 345D MHPU, 349D MHPU and 349D2 MHPU Mobile Hydraulic Power Units Machine Electronic Control System Diagnostic Code List
345D, 349D and 349D2 Excavators and 345D MHPU, 349D MHPU and 349D2 MHPU Mobile Hydraulic Power Units Machine Electronic Control System Event Code List
C7 PETROLEUM Petroleum Engine Atmospheric Pressure Sensor - Remove and Install
Air Conditioning and Heating R134a for All Caterpillar Machines Air Conditioning System Troubleshooting
Air Conditioning and Heating R134a for All Caterpillar Machines Heating and Air Conditioning Service Publications
2012/10/04 Procedure Now Available to Test the Position Sensor of a Hydraulic Cylinder {1439, 7562}
345D, 349D and 349D2 Excavators and 345D MHPU, 349D MHPU and 349D2 MHPU Mobile Hydraulic Power Units Machine Electronic Control System MID 039 - CID 0110 - FMI 04
345D, 349D and 349D2 Excavators and 345D MHPU, 349D MHPU and 349D2 MHPU Mobile Hydraulic Power Units Machine Electronic Control System MID 039 - CID 0110 - FMI 09
C7 PETROLEUM Petroleum Engine Coolant Temperature Sensor - Remove and Install
345D, 349D and 349D2 Excavators and 345D MHPU, 349D MHPU and 349D2 MHPU Mobile Hydraulic Power Units Machine Electronic Control System MID 039 - CID 0190 - FMI 08
Air Conditioning and Heating R134a for All Caterpillar Machines Troubleshooting Heating and Air Conditioning Control System
C7 PETROLEUM Petroleum Engine Engine Oil Pressure Sensor - Remove and Install
345D, 349D and 349D2 Excavators and 345D MHPU, 349D MHPU and 349D2 MHPU Mobile Hydraulic Power Units Machine Electronic Control System MID 039 - CID 0248 - FMI 12