Engine Oil Pump
Show/hide table
| |
| Illustration 1 | g03262836 |
Show/hide table
| Specification for 273-1699 Engine Oil Pump Gp | |||
| Item | Qty | Part | Specification Description |
| 1 | 1 | 298-6387 O-Ring Seal | Before assembly, lubricate lightly with 1E-1597 Rubber Lubricant. |
Show/hide table
| |
| Illustration 2 | g03262716 |
Show/hide table
| Item | Qty | Part | Specification Description |
| 2 | 1 | 107-7175 Spring | Length under test force is Test force is Free length after test is |
Show/hide table
| |
| Illustration 3 | g03262736 |
Show/hide table
| Item | Qty | Part | Specification Description |
| C | 3 | 106-9866 Gear | Length is Depth of the bore in the oil pump body for the new gear |
| D | 2 | 106-9865 Idler Shaft | Diameter is After assembly, bore in the 7W-0060 Bushing for the idler shaft is |
| E | 2 | 4M-3248 Hollow Dowel | Extension from the oil pump cover is |
| F | - | - | Distance from the end of the idler shaft to the gear face is |
| G | 1 | 106-9868 Shaft | Diameter is After assembly, bore in the 7W-0060 Bushing for the idler shaft is |
| H | - | - | Distance from the end of the shaft to the gear face is |
| J | 1 | 7W-0050 Pump Cover | Installation depth of 7W-0060 Bushing in the pump cover is |
| K | 1 | 106-9871 Oil Pump Body As | Installation depth of 7W-0060 Bushing in the oil pump body assembly is |
Show/hide table
| |
| Illustration 4 | g03266016 |
Show/hide table
| Item | Qty | Part | Specification Description |
| L | 2 | 7N-2043 Dowel | Extension from the 1N-4637 Pump Cover |
Show/hide table
| |
| Illustration 5 | g03263001 |
Show/hide table
| Item | Qty | Part | Specification Description |
| M | - | - | Position of 7W-0060 Bushing joints from the centerline through the bearing bores is 45 ± 15 degrees. |
| - | - | - | Bench test specifications:
Unrestricted flow rate at 1000 rpm is Pump pressure at 300 rpm with fully blocked outlet is |
Caterpillar Information System:
3512C Engine for Caterpillar Built Machines Camshaft - Install
3512C Engine for Caterpillar Built Machines Camshaft - Remove
C13T-TH35 and C15T-TH35 Petroleum Packages Engine Operation
Air Conditioning and Heating R134a for All Caterpillar Machines Identifying the Refrigerant
Air Conditioning and Heating R134a for All Caterpillar Machines Temperature Control
C13 On-highway Engine Engine Support (Front)
C13 On-highway Engine Engine Support (Front)
G3500B Engines Fuel Metering Valve
Air Conditioning and Heating R134a for All Caterpillar Machines Identifying the Heating System
Air Conditioning and Heating R134a for All Caterpillar Machines Refrigerant Receiver-Dryer
Specifications and Reusability for Hydraulic Gear Pumps and Motors (Groups 4, 5, and 6) {5061, 5073} Specifications and Reusability for Hydraulic Gear Pumps and Motors (Groups 4, 5, and 6) {5061, 5073}
Air Conditioning and Heating R134a for All Caterpillar Machines In-line Refrigerant Dryer
3512C Engine for Caterpillar Built Machines Crankshaft - Remove
3512C Engine for Caterpillar Built Machines Crankshaft - Install
Loose Caps on Oil Filler Tubes for C7, C9, and C13 On-highway Engines{1316} Loose Caps on Oil Filler Tubes for C7, C9, and C13 On-highway Engines{1316}
345D, 349D and 349D2 Excavators Camera Harness - Disconnect and Connect
2008/04/28 Make Sure That the Bellows Assembly for the Turbocharger Is Installed Correctly {1052}
2008/05/05 New AccuGrade® Firmware is Now Available {7220, 7620}
G3520B Engines Piston and Rings
C175-16 and C175-20 Generator Set Engines Engine Top Speed Is Not Obtained
3500 Generator Sets Air Starting Motor Lubricator Bowl - Clean - If Equipped
3500 Generator Sets Air Starting Motor Lubricator Oil Level - Check - If Equipped
C175-16 and C175-20 Generator Set Engines Prelubrication Pump Problem
AccuGrade® GPS (CD700) Display Registration and Activation