Tilt Control Valve (Dual) - Assemble
Show/hide table
Required Tools | |||
---|---|---|---|
Tool | Part Number | Part Description | Qty |
A | 4C-4030 | Thread Lock Compound | 1 |
Note: Thoroughly clean all parts of the tilt control valve prior to assembly. Inspect the condition of all parts. If any parts are worn or damaged, use new parts for replacement. Lubricate the mating surfaces and all O-ring seals with clean hydraulic oil.
- Install stem (12), retainer (14), spring (15), seal (13), and cover (11).
- Install bolts (10) in cover (11).
Show/hide table
Illustration 3 g01481336 Show/hide tableIllustration 4 g01481312 Show/hide tableImproper assembly of parts that are spring loaded can cause bodily injury.
To prevent possible injury, follow the established assembly procedure and wear protective equipment.
- Install retainer (7), spring (8), seal (9), and cover (6).
- Install bolts (5) in cover (6).
Show/hide table
Illustration 5 g00401988 - Install seals (4) on cartridge assembly (3).
Show/hide table
Illustration 6 g01481332 - Install cartridge assembly (3). Tighten cartridge assembly (3) to a torque of
30 ± 4 N·m (22 ± 3 lb ft) .Show/hide tableIllustration 7 g01481328 - Apply Tooling (A) on the threads of nut (2). Install coil assembly (1) and nut (2). Tighten nut (2) to a torque of
14 ± 3 N·m (10 ± 2 lb ft) .
Show/hide table
Illustration 1 | g01481342 |
Show/hide table
Illustration 2 | g01481316 |
Show/hide table
Improper assembly of parts that are spring loaded can cause bodily injury. To prevent possible injury, follow the established assembly procedure and wear protective equipment. |
Note: Stem (12) is not symmetrical. Install stem (12) according to the alignment marks.
End By:
- Install the tilt control valve. Refer to Disassembly and Assembly, "Tilt Control Valve (Dual) - Install".
Caterpillar Information System:
992K Wheel Loader and 854K Wheel Dozer Power Train Electronic Control Module
993K Wheel Loader Power Train Transmission Oil Pump - Remove
854K Wheel Dozer Machine Systems Tilt Control Valve (Dual) - Disassemble
D6N Track-Type Tractor Ripper Linkage and Cylinder Bearings - Lubricate
992K Wheel Loader and 854K Wheel Dozer Power Train Data Link
992K Wheel Loader and 854K Wheel Dozer Power Train Features
854K Wheel Dozer Machine Systems Tilt Control Valve (Dual) - Install
C4.4 and C6.6 Engines for Caterpillar Built Machines Engine Temperature Sensor Open or Short Circuit - Test
C4.4 and C6.6 Engines for Caterpillar Built Machines Engine Temperature Sensor Open or Short Circuit - Test
854K Wheel Dozer Hydraulic System System Pressure - Release
Installation of the Ladder On the D11R and D11T Track-Type Tractor {7254} Installation of the Ladder On the D11R and D11T Track-Type Tractor {7254}
C4.4 and C6.6 Engines for Caterpillar Built Machines Engine Speed/Timing Sensor Circuit - Test
D6N Track-Type Tractor Steering Charge Filter - Replace
D6N Track-Type Tractor Track - Check/Adjust
D6N Track-Type Tractor Transmission Oil Filter - Replace
Some 3500 Cylinder Packs May Have Incorrect Pistons{1225} Some 3500 Cylinder Packs May Have Incorrect Pistons{1225}
D6N Track-Type Tractor Transmission Oil Level - Check
992K Wheel Loader and 854K Wheel Dozer Power Train Electrical Input Components
D6N Track-Type Tractor Window Washer Reservoir - Fill
D5R Track-Type Tractor Fuses and Circuit Breakers - Replace/Reset
C4.4 and C6.6 Engines for Caterpillar Built Machines Ether Starting Aid - Test
Parts to Replace in the Event of Hydraulic Lock or Piston to Valve Contact{1000, 1102, 1216, 1225, 1250, 1290} Parts to Replace in the Event of Hydraulic Lock or Piston to Valve Contact{1000, 1102, 1216, 1225, 1250, 1290}
973D Track-Type Loader Power Train Recoil Spring - Disassemble
854K Wheel Dozer Machine Systems Push Arms and Blade - Remove