Transmission Neutralizer Override Control{1435, 7451} Caterpillar


Transmission Neutralizer Override Control{1435, 7451}

Usage:

R1300 6QW


Load Haul Dump:
R1300 (S/N: 6QW1-UP)
R1300G Series II (S/N: RSL1-UP)
R1300G (S/N: LJB1-UP)
R1300G (S/N: NJB1-UP)

Introduction




Illustration 1g01051135

The supplemental product support literature should be used with the appropriate Service Manual and the appropriate Parts Manual that is available for each standard machine. This supplement is used to determine the difference between the custom modifications and a standard machine.

The Service Manual and the Parts Manual available for the standard machine should be used if service information is not in this supplementary product support literature.

Operation




Illustration 2g01467871

R1300 S/N:6QW1-UP

(1) Transmission neutralizer override switch




Illustration 3g01467872

R1300G S/N:LJB1-UP, R1300G II S/N:RSL1-UP and R1300G S/N:NJB1-UP

(1) Transmission neutralizer override switch


Transmission Neutralizer Override Switch (1) - The transmission neutralizer override switch is a two-position switch.

Move the switch to the upper position to deactivate the transmission neutralizer. The service brake and transmission neutralizer pedal will now operate as a conventional service brake pedal.

Move the switch to the lower position to activate the transmission neutralizer. When the service brake and transmission neutralizer pedal is depressed, the service brake will apply, and the transmission will be disengaged, allowing the operator to increase engine speed for improved hydraulic performance.

Transmission Neutralizer Function




Illustration 4g01467907

R1300 S/N:6QW1-UP

(1) Service brake and transmission neutralizer pedal




Illustration 5g01521094

R1300 S/N:6QW1-UP

(2) Transmission neutralizer limit switch




Illustration 6g01467928

R1300G S/N:LJB1-UP, R1300G II S/N:RSL1-UP and R1300G S/N:NJB1-UP

(1) Service brake and transmission neutralizer pedal

(2) Transmission neutralizer limit switch

The transmission neutralizer limit switch (2) is located in the operator station and is activated by depressing service brake and transmission neutralizer pedal (1) .

When the service brake and transmission neutralizer pedal is depressed, the normally closed contacts of transmission neutralizer limit switch open. The open contacts interrupt the power from the Power Train ECM. causing the Power Train ECM to neutralize the transmission. The engine rpm will increase when the transmission is neutralized due to the no-load condition from the transmission, allowing full hydraulic power for worktool operation.

Note: On R1300G and R1300G II machines, when transmission is neutralized, the gear indicator shows the speed that is selected and the direction will show neutral.

Note: On R1300 S/N:6QW machines, the gear readout on the monitor does not change when the transmission is neutralized. The monitor continues to show the speed and direction that will be engaged when the pedal is released.




Illustration 7g01467948

R1300 S/N:6QW1-UP

(3) Transmission neutralizer override switch




Illustration 8g01467950

R1300G S/N:LJB1-UP, R1300G II S/N:RSL1-UP and R1300G S/N:NJB1-UP

(3) Transmission neutralizer override switch

The transmission neutralizer override switch (3) is an input to the Power Train ECM. The input is used by the Power Train ECM to determine if the transmission neutralizer should be enabled or disabled.

When the machine is started, the transmission neutralizer is enabled.

Move the switch to the upper position to deactivate the transmission neutralizer. The service brake and transmission neutralizer pedal will now operate as a conventional service brake pedal.

Move the switch to the lower position to activate the transmission neutralizer. When the service brake and transmission neutralizer pedal is depressed, the service brake will apply and the transmission will be disengaged, allowing the operator to increase engine speed for improved hydraulic performance.

Switches (R1300 S/N:6QW1-UP, R1300G ; S/N:LJB1-UP and R1300G ; S/N:NJB1-UP)

Transmission Neutralizer Limit Switch




Illustration 9g00287699

Transmission neutralizer limit switch

The transmission neutralizer limit switch is an input of the Power Train Electronic Control Module (ECM). The transmission neutralizer limit switch is a two-position limit switch. The transmission neutralizer limit switch informs the Power Train ECM when the service brake and transmission neutralizer pedal is depressed.

When the transmission neutralizer limit switch is activated (brake pedal pressed), the switch is open. When the switch is open (not grounded), the Power Train ECM neutralizes the transmission. When the transmission neutralizer limit switch is deactivated (brake pedal released), the switch closes contact J2-4 of the Power Train ECM to ground. The COM terminal is connected to frame ground. The N/C terminal of the switch is not used.

Transmission Neutralizer Override Switch




Illustration 10g01470134

Transmission neutralizer override switch R1300 S/N:6QW1-UP




Illustration 11g01521073

Transmission neutralizer override switch R1300G S/N:LJB1-UP and R1300G ; S/N:NJB1-UP

The transmission neutralizer override switch is an input to the Power Train Electronic Control Module (ECM). The transmission neutralizer override switch has two positions. The ON position and the OFF position.

The transmission neutralizer override switch signals the Power Train ECM to enable/disable the neutralizing function of the left brake pedal.

When the transmission neutralizer override switch is in the ON position, contact J2-4 of the Power Train ECM is always grounded, overriding the operation of the transmission neutralizer override switch on the left brake pedal and stops the transmission neutralizer function. When the transmission neutralizer override switch is in the OFF position, the transmission neutralizer limit switch on the left brake pedal operates as normal.

Switches (R1300G II S/N:RSL1-UP)

Transmission Neutralizer Limit Switch




Illustration 12g00287699

Transmission neutralizer limit switch

The transmission neutralizer limit switch is an input of the Power Train Electronic Control Module (ECM). The transmission neutralizer limit switch is a two-position limit switch. The transmission neutralizer limit switch informs the Power Train ECM when the service brake and transmission neutralizer pedal is depressed.

When the transmission neutralizer limit switch is activated (brake pedal pressed), the switch is open. When the switch is open (not grounded), the Power Train ECM neutralizes the transmission. When the transmission neutralizer limit switch is deactivated (brake pedal released), the switch closes contact J2-31 of the Power Train ECM to ground. The COM terminal is connected to frame ground. The N/C terminal of the switch is not used.

Transmission Neutralizer Override Switch




Illustration 13g01521073

Transmission neutralizer override switch R1300G II S/N:RSL1-UP

The transmission neutralizer override switch is an input to the Power Train Electronic Control Module (ECM). The transmission neutralizer override switch has two positions. The ON position and the OFF position.

The transmission neutralizer override switch signals the Power Train ECM to enable/disable the neutralizing function of the left brake pedal.

When the transmission neutralizer override switch is in the ON position, contact J2-31 of the Power Train ECM is always grounded, overriding the operation of the transmission neutralizer override switch on the left brake pedal and stops the transmission neutralizer function. When the transmission neutralizer override switch is in the OFF position, the transmission neutralizer limit switch on the left brake pedal operates as normal.

Transmission Neutralizer Override Control Electrical Schematic (R1300 S/N:6QW1-UP, R1300G ; S/N:LJB1-UP and R1300G ; S/N:NJB1-UP)




Illustration 14g01519383

Transmission Neutralizer Override Control Electrical Schematic (R1300G II S/N:RSL1-UP)




Illustration 15g01519387

Caterpillar Information System:

793F and 793F XQ Off-Highway Truck Hydraulic Fan and Steering System Metering Pump (Steering)
2009/03/16 Improved Life for the Circle Drive on Certain Motor Graders {5207}
Correction for Capacity of the Hydraulic Tank{5056} Correction for Capacity of the Hydraulic Tank{5056}
793F CMD Off-Highway Truck Hydraulic Fan and Steering System Steering Control Valve
793F AC Off-Highway Truck Hydraulic Fan and Steering System Oil Cooler (Hydraulic Fan, Steering)
793F CMD Off-Highway Truck Hydraulic Fan and Steering System Accumulator (Steering)
793F and 793F XQ Off-Highway Truck Hydraulic Fan and Steering System Solenoid and Relief Valve (Steering)
120K Motor Grader Crankshaft Vibration Damper - Inspect
12K, 140K and 160K Motor Graders Cooling System Coolant Level - Check
12K, 140K and 160K Motor Graders Cooling System Coolant Sample (Level 1) - Obtain
966H Wheel Loader and 972H <BR>Wheel Loader Power Train MID 081 - CID 0622 - FMI 04
966H Wheel Loader and 972H <BR>Wheel Loader Power Train MID 081 - CID 0622 - FMI 03
C175-16 Locomotive Engine Exhaust Manifold
C4.4 and C6.6 Engines for Caterpillar Built Machines CID 0091 FMI 02
C4.4 and C6.6 Engines for Caterpillar Built Machines CID 0091 FMI 08
793F AC Off-Highway Truck Hydraulic Fan and Steering System Pressure Sensors
Inspection and Repair of the Door Strut System on Certain Forest Machines and Track Feller Bunchers{5138, 7308} Inspection and Repair of the Door Strut System on Certain Forest Machines and Track Feller Bunchers{5138, 7308}
793F AC Off-Highway Truck Hydraulic Fan and Steering System General Information
793F CMD Off-Highway Truck Hydraulic Fan and Steering System Visual Inspection
793F CMD Off-Highway Truck Hydraulic Fan and Steering System Pump Rotating (Steering) Pressure - Test and Adjust
C4.4 and C6.6 Engines for Caterpillar Built Machines CID 0174 FMI 03
793F and 793F XQ Off-Highway Truck Hydraulic Fan and Steering System Relief Valve (Steering) - Test and Adjust
793F AC Off-Highway Truck Hydraulic Fan and Steering System Steering Control Valve - Adjust
AS2252C Asphalt Screed Height Adjuster Group (Extender) - Assemble
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.