SR5 Electric Power Generation Caterpillar


Bus Bar - Remove and Install

Usage:

SR5 G1E

母线拆卸和安装

母线拆卸

只有在执行了关机程序和断电闭锁程序,将要保养的发电机关闭和绝缘之后,才能执行下面的步骤。




图 1g01572313

(1) 中心母线

(2) 分接母线

(3) 可选断路器母线




图 2g01573011

分接母线示例




图 3g01573013

跨线接法示例

(5) 跨线

  1. 根据需要拆卸接线盒面板或接线盒,以便于够到母线总成。 请参阅本文档的"接线盒 - 拆卸和安装"部分。

  1. 拆卸母线螺栓 (6) 。



    图 4g01461533

    (6) 母线螺栓

  1. 拆卸固定支架 (9) 的安装螺栓 (8) 。 移开固定支架 (9) ,以便支架不会妨碍拆卸过程。 移开引线,以便引线不会妨碍拆卸过程。

    注: 低压发电机配有电流变压器 (CT) 总成。 CT 总成会连接到母线上。 首先断开 CT 电线引线,然后可以将 CT 总成 (7) 放置在合适位置,拆卸母线总成。

    注: 支架的确切样式和安装螺栓的数量因具体应用而异。




    图 5g01461534

    1400 机架母线固定支架和安装螺栓的示例。

    (7) 电流变压器 (CT) 总成

    (8) 安装螺栓

    (9) 固定支架

  1. 断开发电机励磁线圈引线电缆总成 (11) 与母线 (10) 之间的连接。



    图 6g01463667

  1. 拆卸用于将母线安装支架 (13) 装配到后支架 (14) 的剩余安装螺栓 (12) 。



    图 7g01463668

    (12) 安装螺栓

    (13) 母线安装支架

    (14) 后支架

  1. 拆卸母线总成。

母线安装


注意

必须正确旋紧所有电源连接紧固件硬件。 有关每个螺栓和螺母的大小,请参阅卡特彼勒技术规格。 未能旋紧紧固件硬件会导致电缆过热并可能损坏发电机。


母线的安装过程与拆卸步骤顺序相反。

  1. 将母线支架 (13) 安放在正确的位置上。 安装安装螺栓 (12) 。 参见图 7。

  1. 将发电机励磁线圈引线电缆总成 (18) 连接到母线 (17) 。

    注: 在将励磁线圈引线电缆总成 (18) 安装到母线 (17) 时需格外小心。 防止在安装过程中过度抻拉和弯曲电缆。 请确保电缆不与定子的金属边缘接触。




    图 8g01696957

  1. 安装固定支架 (21) 安装螺栓 (20) 。

    注: 低压发电机配有电流变压器 (CT) 总成。 CT 总成 (19) 仍应连接到母线上。 在已将母线装配到发电机上后,连接 CT 电线引线。

    注: 支架的确切样式和安装螺栓的数量因具体应用而异。




    图 9g01696973

    1400 机架母线固定支架和安装螺栓的示例。

    (19) 电流变压器 (CT) 总成

    (20) 安装螺栓

    (21) 固定支架

  1. 安装母线螺栓 (24) 。



    图 10g01696974

  1. 根据需要安装拆卸掉的接线盒面板或接线盒,以便于够到母线总成。 请参阅本文档的"接线盒 - 拆卸和安装"部分。

Caterpillar Information System:

345D, 349D and 349D2 Excavators Hydraulic System Travel Hydraulic System
3176C, 3406E and 3456 Industrial Engines Intake Manifold Air Pressure Is High
3176C, 3406E and 3456 Industrial Engines ECM Software - Install
345D, 349D and 349D2 Excavators Hydraulic System Solenoid Valve (Fine Swing) - If Equipped
2008/06/02 An Improved Alternator Belt Guard Is Now Used {7174}
345D, 349D and 349D2 Excavators Hydraulic System Relief Valve (Cushion Crossover) - Anti-Reaction Valves
2008/02/25 A New Oil Filter Group is Now Used on the TH48-E80 Oil/Gas Transmission {3030, 3067}
345D, 349D and 349D2 Excavators Hydraulic System Oil Makeup (Swing System)
C18 Marine and Marine Generator Set Engines Turbocharger
C175-16 and C175-20 Generator Set Engines Crankcase Pressure Is High
C175-16 and C175-20 Engines for Off-Highway Trucks Camshaft
3500 Engines Engine Oil Cooler Bypass and Cooling Jet Sequence Valves
C175-16 and C175-20 Generator Set Engines Injector Solenoid - Test
The Idle Shutdown Timer May Cause the Engine to Shut Down During Regenerations Initiated with Caterpillar Electronic Technician (ET){108B} The Idle Shutdown Timer May Cause the Engine to Shut Down During Regenerations Initiated with Caterpillar Electronic Technician (ET){108B}
C15 Petroleum Generator Set Engines Speed Sensor
C13, C15, and C18 Generator Set Engines Camshaft
3500B Engines and 776D, 777D, 784C, 785C, 789C, 793C and 793D Off-Highway Truck/Tractors Crankcase Breather
C175-16 and C175-20 Generator Set Engines Flywheel Housing
3176C, 3406E and 3456 Industrial Engines Sensor Signal (PWM) - Test
345D, 349D and 349D2 Excavators Hydraulic System Pilot Valve (Travel)
C175 Generator Sets Fuel System Primary Filter - Clean/Inspect/Replace
345D, 349D and 349D2 Excavators Hydraulic System Travel Counterbalance Valve
345D, 349D and 349D2 Excavators Hydraulic System Oil Makeup (Travel System)
345D, 349D and 349D2 Excavators Hydraulic System Control Valve (Straight Travel)
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.