Procedure to Handle and Ship Diesel Particulate Filters (DPF) and Catalytic Converter Mufflers (CCM){1091, 1091} Caterpillar


Procedure to Handle and Ship Diesel Particulate Filters (DPF) and Catalytic Converter Mufflers (CCM){1091, 1091}

Usage:

D3400 01T
Engine:Commercial All
Engine:Truck All
Generator Set: All
Machine Engines: All
Marine Engine: ALL

Introduction


NOTICE

Diesel Particulate Filters (DPF) and Catalytic Converter Mufflers (CCM) are not applicable to all engines. Some engines contain a DPF and a CCM device that were installed as original equipment to meet engine emissions certification requirements. However, some engines may have had the devices installed during a retrofit program for emissions reduction.


Do not perform any procedure in this Special Instruction until you read this information and you understand this information.

Procedure for Shipping the Diesel Particulate Filters (DPF)

------ WARNING! ------

Wear goggles, gloves, protective clothing, and a National Institute for Occupational Safety and Health (NIOSH) approved P95 or N95 half-face respirator when handling a used Diesel Particulate Filter or Catalytic Converter Muffler. Failure to do so could result in personal injury.

----------------------

Place all the used Diesel Particulate Filter (DPF) center sections, regardless of condition, into a 0.152 mm (0.006 inch) thick plastic bag. Make sure that the bag is sealed before placing the DPF into a shipping container. This must be performed in order to contain any constituents from the used DPF during shipping. New replacement diesel particulate filters may come with a 0.152 mm (0.006 inch) plastic bag that can be used for wrapping the used DPF.

Procedure for Shipping the Catalytic Converter Mufflers (CCM)

Seal the inlet port and the outlet port on all used Catalytic Converter Mufflers (CCM) with rubber caps or plastic caps. Various sized plastic caps can be ordered from the Cat Shop Supplies and Hand Tools catalog. Reference caps and plugs under the Shop Supplies section. An alternative is to seal the inlet ports and outlet ports with a 0.152 mm (0.006 inch) thick sheet of plastic and 50 mm (2 inch) wide sealing tape with good adhesive properties before shipping. Sealing or capping must be performed in order to contain any constituents from the used CCM during shipping.

Caterpillar Information System:

Procedure for Cleaning Ash from the Diesel Particulate Filter (DPF) for Certain Caterpillar Engines{108F, 1091} Procedure for Cleaning Ash from the Diesel Particulate Filter (DPF) for Certain Caterpillar Engines{108F, 1091}
C4.4 Industrial Engine Accessory Drive - Install
C4.4 Industrial Engine Accessory Drive - Assemble
C4.4 Industrial Engine Accessory Drive - Disassemble
C4.4 Industrial Engine Accessory Drive - Remove
345D, 349D and 349D2 Excavators Hydraulic System Travel on Level Ground - Test - Optional Test
C11 and C13 Petroleum Engines Accessory Drive - Install
345D, 349D and 349D2 Excavators Hydraulic System Engine Performance - Test - Engine Speed
C11 and C13 Petroleum Engines Accessory Drive - Remove
Installation Instructions for the New Caterpillar Digital Voltage Regulator (CDVR) In Field Retrofit Applications{4467} Installation Instructions for the New Caterpillar Digital Voltage Regulator (CDVR) In Field Retrofit Applications{4467}
Software Update for Model Year 2007 C7 On-Highway Engine in General Motor Chassis{1901} Software Update for Model Year 2007 C7 On-Highway Engine in General Motor Chassis{1901}
C11 and C13 Petroleum Engines Flywheel Housing - Remove and Install
C9 Marine Auxiliary and Generator Set Engines Configuration Parameters
G3500B Engines Water Temperature Regulator
C13T-TH35 and C15T-TH35 Petroleum Packages Plate Locations and Film Locations
2008/02/11 The Wiring Harness for the Turbocharger Compressor Outlet Pressure Sensor has been Rerouted {1403, 1408, 1917}
345D, 349D and 349D2 Excavators Hydraulic System Travel on Level Ground - Test
345D, 349D and 349D2 Excavators Hydraulic System Swing Speed and Swing Drift on a Slope - Check
C11 and C13 Engines for Caterpillar Built Machines Valve Mechanism Cover - Remove and Install
C15 On-Highway Engine Diesel Particulate Filter - Disassemble
345D, 349D and 349D2 Excavators Hydraulic System Cylinder Speed - Check
C15 On-Highway Engine Diesel Particulate Filter - Assemble
345D, 349D and 349D2 Excavators Hydraulic System Relief Valve (Line) - Test and Adjust
G3508 "A" to G3508 with ADEM 3 ECM Upgrade for Enhanced Performance of 1400 RPM Engines{1000, 1052, 1270, 191N} G3508 "A" to G3508 with ADEM 3 ECM Upgrade for Enhanced Performance of 1400 RPM Engines{1000, 1052, 1270, 191N}
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.