2008/04/14 Caterpillar


New Processes Improve Registration of Product Link {7338, 7606}

Usage:

769C 01X
Caterpillar Products:
  • All
  • Two improvements have been made to the provisioning process for the 263-9088 Communication Electronic Control Module (PRODUCT LINK 121SR). The 263-9088 Communication Electronic Control Module (PRODUCT LINK 121SR) is commonly known as the Product Link 121SR or PL121SR. Provisioning is the process of supplying the identification number of the radio components to the satellite network provider. These identification numbers authorize communication between the PL121SR and the communication satellites. A unit cannot be registered if the unit is not provisioned.

    Note: The 263-9088 Communication Electronic Control Module (PRODUCT LINK 121SR) is an integral component of the PL321SR system.

    The first improvement was to implement a 100% end of line inspection to eliminate the possibility of unprovisionined PL121SR from reaching the parts supply system. The end of line inspection has been active since August 2007.

    The second improvement was to simplify the provisioning process by removing many unnecessary communication steps. The new provisioning process will eliminate any unprovisioned units from the supply chain. Any PL121SR provisioned under the new process can be identified by the changes to the module ID number. Refer to Illustration 1. Previous ID numbers began with "DQ02". New module ID numbers will begin with the letters "DQCAT" and are followed by seven digits.




    Illustration 1g01453718

    (1) ID number

    Note: If your PL121SR / PL321SR module has registered successfully, the module is provisioned and does not need to be replaced. If your PL121SR / PL321SR module has not registered successfully, contact support prior to replacing.

    Caterpillar Information System:

    C11 and C13 Petroleum Engines Engine Oil Cooler - Install
    C18 Industrial Engines Speed Sensor - Clean/Inspect
    Downloading Programs to Power Generation Equipment with the Execloader Software{7620} Downloading Programs to Power Generation Equipment with the Execloader Software{7620}
    C11 and C13 Petroleum Engines Engine Oil Cooler - Remove
    C11 and C13 Petroleum Engines Exhaust Manifold - Remove and Install
    Seizure of Thermocouple Threads in Some G3500C and G3500E Exhaust Manifolds{1408, 1900, 7498} Seizure of Thermocouple Threads in Some G3500C and G3500E Exhaust Manifolds{1408, 1900, 7498}
    2008/05/19 Improved Oil Return Lines for the Turbocharger are Used {1052, 1307}
    C11 and C13 Petroleum Engines Turbocharger - Install
    2008/04/01 New Mounting for the Temperature Sensor Is Now Used {108B, 108E, 108M}
    2008/03/01 A New Spring Guide for the Camshaft Lifter is Used {1209}
    C7 Petroleum Engines Cooling System - Check - Overheating
    C11 and C13 Petroleum Engines Turbocharger - Remove
    A New Purge Pump and Service Pack are Now Used{107P} A New Purge Pump and Service Pack are Now Used{107P}
    C11 and C13 Petroleum Engines Water Pump - Remove
    2008/02/11 Use of Remanufactured Injectors in Marine Engines {1290}
    2008/04/21 Improved Exhaust Risers and Brackets are Now Used {1059}
    C11 and C13 Petroleum Engines Water Pump - Install
    C11 and C13 Petroleum Engines Water Temperature Regulator - Remove and Install
    2008/07/21 Improved Fuel Injection Pump {1251, 1714}
    C11 and C13 Petroleum Engines Flywheel - Remove
    C13 and C15 Engines for Combat and Tactical Vehicles Air Inlet Shutoff Circuit - Test
    C11 and C13 Petroleum Engines Flywheel - Install
    C11 and C13 Petroleum Engines Crankshaft Rear Seal - Remove
    C11 and C13 Petroleum Engines Crankshaft Rear Seal - Install
    Back to top
    The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
    CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.