Differential and Bevel Gear - Install
安装步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件描述     | 数量     |
A     | 138-7576     | 连杆支架     | 3     |
B     | 1U-7234     | 塞尺     | 1     |
- 彻底清洁差速器和伞齿轮和轴壳体的配合表面。 用新的零件替换 O 形密封圈。
- 在差速器和伞齿轮上安装 O 形密封圈 (14) 。
Show/hide table
图 1 | g01447852 |
- 将工具 (A) 和适当的起吊设备连接到差速器和伞齿轮 (13) 上。 差速器及伞齿轮 (13) 的重量约为 816 kg (1800 lb)。
Show/hide table
图 2 | g01448013 |
- 使用工具 (A) 和适当的起吊设备以将差速器和伞齿轮 (13) 安装到车桥壳中。
- 安装螺栓 (12) 。 拧紧螺栓 (12) 至扭矩为 300 ± 30 N·m (221 ± 22 lb ft)。 将螺栓 (12) 额外上紧 120° ± 10°。
Show/hide table
图 3 | g01447841 |
- 将支架 (10) 和所有管子作为一个单元安装。
Show/hide table
图 4 | g01447738 |
- 安装螺栓 (9) 以将支架 (10) 固定到差速器和伞齿轮上。 拧紧螺栓 (9) 至扭矩为 300 ± 30 N·m (221 ± 22 lb ft)。 然后,将螺栓 (9) 额外上紧 120° ± 10°。
- 将管组件 (7) 和 (8) 连接到每个行车制动器上。
- 将夹子 (11) 连接到管组件 (7) 和 (8) 上。
- 将护罩组件 (6) 安装到后桥组件上。
Show/hide table
图 5 | g01447728 |
- 在销 (4) 上安装 O 形密封圈 (5) 。
Show/hide table
图 6 | g01447722 |
- 使用密封的机油润滑销 (4) 和 O 形密封圈 (5) 。 将销 (4) 安装到车桥壳中。
- 不用垫片安装盖子 (1) 。
Show/hide table
图 7 | g01448031 |
- 安装螺栓 (2) 。 将螺栓 (2) 紧固到足以去除销 (4) (未显示)和盖 (1) 之间的端隙。
- 用工具 (B) 以便测量盖 (1) 和车桥壳之间的间隙。 记录这个测量值。 使用该测量值以便确定所需垫片的正确厚度。
- 安装适当厚度的垫片,以便在销 (4) (未显示)内设定一个 −0.03 mm (−0.001 in) 的预负载到一个 0.03 mm (0.001 in) 的轴向间隙。
- 用测定量的垫片 (3) 安装盖 (1) 。 安装螺栓 (2) 。
Show/hide table
图 8 | g01447717 |
End By:
- 安装后车桥的前支架。 请参阅 拆解与组装, "耳轴支架(摆动轴,前)- 安装"。
- 安装半轴。 请参阅 拆解和装配, "车桥轮轴 - 拆卸和安装"。
- 安装车桥。 请参阅 拆解和组装, "摆动轴(后)- 安装",或者参阅 拆解和组装, "固定轴(前)- 拆卸和安装"。
Caterpillar Information System:
993K Wheel Loader Steering System General Information (Steering)
IT38H Integrated Toolcarrier and 938H Wheel Loader Transmission Electronic Control System MID 081 - CID 0600 - FMI 04
Installation Instructions for the 301-6925 Joystick Control Gp (2-Function) and the 301-6926 Joystick Control Gp (3-Function) both with a transmission direction control switch{5063, 5705} Installation Instructions for the 301-6925 Joystick Control Gp (2-Function) and the 301-6926 Joystick Control Gp (3-Function) both with a transmission direction control switch{5063, 5705}
IT38H Integrated Toolcarrier and 938H Wheel Loader Transmission Electronic Control System MID 081 - CID 0600 - FMI 03
Installation Instructions for the 301-6928 Secondary Steering Ar (Kit){4300, 4304, 4324, 4334, 5927} Installation Instructions for the 301-6928 Secondary Steering Ar (Kit){4300, 4304, 4324, 4334, 5927}
IT38H Integrated Toolcarrier and 938H Wheel Loader Transmission Electronic Control System MID 081 - CID 0590 - FMI 09
IT38H Integrated Toolcarrier and 938H Wheel Loader Transmission Electronic Control System MID 081 - CID 0590 - FMI 02
854K Wheel Dozer and 992K Wheel Loader Power Train System Schematic
IT38H Integrated Toolcarrier and 938H Wheel Loader Transmission Electronic Control System MID 081 - CID 0444 - FMI 06
IT38H Integrated Toolcarrier and 938H Wheel Loader Transmission Electronic Control System MID 081 - CID 0444 - FMI 05
992K Wheel Loader Electrohydraulic System Relief Valve (Implement Pilot) - Test and Adjust
IT38H Integrated Toolcarrier and 938H Wheel Loader Transmission Electronic Control System MID 081 - CID 0444 - FMI 03
992K Wheel Loader Electrohydraulic System Pressure Reducing Valve Pressure for Dead Engine Pilot Supply (Engine OFF) - Test and Adjust
993K Wheel Loader Steering System Piston Pump (Steering) Margin Pressure - Test and Adjust
Troubleshooting for 930G Wheel Loaders that Exhibit Dead Implement Functions{4320, 5050, 5057} Troubleshooting for 930G Wheel Loaders that Exhibit Dead Implement Functions{4320, 5050, 5057}
854K Wheel Dozer Machine Systems Brake Accumulator - Remove
854K Wheel Dozer Machine Systems Brake Accumulator - Install
992K Wheel Loader Electrohydraulic System Pilot Control Actuator Pressure - Check
992K Wheel Loader Electrohydraulic System Electrical Input Components
992K Wheel Loader and 854K Wheel Dozer Power Train Differential and Bevel Gear - Disassemble
993K Wheel Loader Machine Systems Hydraulic Tank (Implement, Hydraulic Fan) - Disassemble
992K Wheel Loader Electrohydraulic System Electrical Output Components
854K Wheel Dozer Machine Systems Brake Control Valve (Service) - Remove and Install
992K Wheel Loader Electrohydraulic System Ride Control Signal Pressure - Check