Trunnion Support (Oscillating Axle, Front) - Assemble
组装步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件描述     | 数量     |
B     | 8M-9012     | 板     | 1     |
C     | 6V-6640     | 密封胶     | 1     |
D     | 5P-0960     | 润滑脂筒     | 1     |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
注: 检查密封件有无磨损或损坏。 如有必要,请更换部件。
- 将前耳轴支架 (1) 放置在适当的压具中。 确保前耳轴支架 (1) 的护圈侧朝上。 前耳轴支架 (1) 的重量约为 204 kg (450 lb)。
Show/hide table
图 1 | g01446848 |
Show/hide table
图 2 | g01446842 |
- 采用工具 (B) 和适当的压具安装套筒轴承 (6) ,使套筒轴承 (6) 座合在前耳轴支架 (1) 的台肩上。
- 安装油封 (5) 。
- 将工具 (C) 涂抹到挡圈 (2) 的配合面上。 安装挡圈 (2) 和螺栓 (4) 。
Show/hide table
图 3 | g00383652 |
- 安装油封 (3) 。
- 将工具 (D) 涂敷在油封 (3) 、油封 (5) (未显示)和套筒轴承 (6) (未显示)上。
End By: 安装后桥上的前耳轴支架。 请参阅 拆解和组装, "耳轴支架(摆动桥,前)- 安装"。
Caterpillar Information System:
992K Wheel Loader and 854K Wheel Dozer Power Train Trunnion Support (Oscillating Axle, Front) - Disassemble
Failed Relays are Reported in the Secondary Steering System{4493, 7620} Failed Relays are Reported in the Secondary Steering System{4493, 7620}
992K Wheel Loader and 854K Wheel Dozer Power Train Trunnion Support (Oscillating Axle, Front) - Install
993K Wheel Loader Electrohydraulic System Pump Performance (Implement) (Lift Time) - Test
994F Wheel Loader Pump Drive (Rear) to Engine - Connect
2008/02/11 The Improved Software for the Autolube {7540, 7610, 7620}
992K Wheel Loader and 854K Wheel Dozer Braking System Brake System Troubleshooting
2008/01/28 New Driveline Components Improve Service Life of Wheel Loaders {3253, 3267}
2007/12/31 A New Calibration Procedure is Now Available {4269}
992K Wheel Loader and 854K Wheel Dozer Steering System Gear Pump (Steering Oil Cooler) (Steering Pilot)
994F Wheel Loader Pump Drive (Rear) from Engine - Separate
993K Wheel Loader Electrohydraulic System Piston Pump Margin Pressure (Hydraulic Fan) - Test and Adjust
993K Wheel Loader Power Train Torque Converter Stall (3FWD) - Test
854K Wheel Dozer Oil Renewal System Oil - Add - If Equipped
993K Wheel Loader Power Train Torque Converter Stall (1FWD) - Test
993K Wheel Loader Electrohydraulic System Torque Converter Stall and Implement Pump Double Stall - Test
993K Wheel Loader Power Train Differential Backlash and Bearings - Adjust
993K Wheel Loader Electrohydraulic System Pressure Reducing Valve (Implement Pilot Oil) - Test and Adjust
C9.3 Tier 4 Final Engines Engine Oil Filter Base
994H Wheel Loader Machine Systems Window Wiper and Wiper Motor (Rear) - Install
993K Wheel Loader Steering System Steering System Pressure (High Pressure Stall) - Test and Adjust
992K Wheel Loader and 854K Wheel Dozer Power Train Axle Shaft - Remove and Install
994H Wheel Loader Machine Systems Window Wiper and Wiper Motor (Front) - Install
854K Wheel Dozer and 992K Wheel Loader Power Train MID 081 - CID 0590 - FMI 14