Service Brake Wear Indicator - Check
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修发动机时,请小心确保盛接流出的液体。 在打开或拆解任何储有液体的部件之前,要准备好合适的容器收集液体。 有关适合收集和盛接卡特彼勒产品上的液体的工具和供应品,请参阅专门出版物, NENG2500, "卡特彼勒代理商工具目录"。 按照本地法规和条例处置所有液体。 |
该步骤要求两个人作业。 一个人必须接合行车制动器,另一个人必须测量制动盘的磨损。 进行该步骤时务必要小心。 制动系统可能会发生机油泄漏。 让所有人员远离机器或在操作员的视野范围内。
- 把车辆停放在远离其它设备和其它人员的水平路面上,并将机具降到地面。 将变速箱置于空档位置。 接合停车制动器并把发动机关闭。
- 安装转向锁并用楔块塞住车轮。
- 起动发动机以建立制动系统压力。
- 停止发动机。 进行下一步骤前,先让车桥油沉淀一会儿。
注: 测量制动器磨损时,保持发动机停机。
- 按下各个车桥断路器卸压阀顶上的按钮,以便释放所有压力。
注: 有关车桥断路器卸压阀的位置,请参阅操作和保养手册, "车桥断路器卸压阀 - 清洁"。
- 在螺塞下放置一个合适容器,以收集制动系统的机油。
- 踩下并踩住行车制动器踏板。
- 拆下螺塞。
Show/hide table
图 1 | g01446483 |
- 将 FT3105 制动器磨损检测仪 插入到检测孔中。
如果制动器磨损检测仪不会完全插入检测孔中,则表明制动器磨损小于 50%。 转至步骤 12。
如果制动器磨损检测仪完全插入检测孔中,则表明制动器磨损大于 50%。 转至步骤 10。
Show/hide table
注意 |
---|
当塞孔中安装有销时,不要让制动器活塞缩回。 制动器活塞缩回时可能会使销折断。 销的碎片可能会掉进制动器壳体中,造成损坏。 |
- 将 FT3104 制动器磨损检测仪 插入到检测孔中。
如果制动器磨损检测仪不会完全插入检测孔中,则表明制动器磨损在 50% 和 75% 之间。 转至步骤 12。
如果制动器磨损检测仪完全插入检测孔中,则表明制动器磨损大于 75%。 转至步骤 11。
- Insert a FT3103 制动器磨损检测仪 插入到检测孔中。
如果制动器磨损检测仪不会完全插入检测孔中,则表明制动器磨损在 75% 和 100% 之间。 应尽快进行制动器维修。
如果制动器磨损检测仪完全插入检测孔中,则表明制动器磨损大于 100%。 应立即进行制动器维修。
- 拆卸制动器磨损检测仪。
- 松开行车制动器踏板。
- 安装螺塞。
- 清除溅溢的油液。
- 对于各个行车制动器,重复步骤 1 到 15。
Caterpillar Information System:
2008/01/21 New O-Ring Seal and an Improved Cover for the Diverter Valve {5066, 5304}
992K Wheel Loader and 854K Wheel Dozer Power Train Oscillating Axle (Rear) - Install
992K Wheel Loader and 854K Wheel Dozer Steering System High Pressure Screen Group (Deluxe Filtration)
C15 and C18 Engines for Caterpillar Built Machines Valve Actuator (Variable) - Install
854K Wheel Dozer and 992K Wheel Loader Power Train MID 081 - CID 0590 - FMI 09
2008/01/07 Rubber Pads on the Stops for the Steering Have Been Improved {4304, 7188}
993K Wheel Loader Engine Supplement Alternator - Remove and Install
854K Wheel Dozer and 992K Wheel Loader Power Train MID 081 - CID 0585 - FMI 08
993K Wheel Loader Power Train Wheel Bearings - Adjust
992K Wheel Loader and 854K Wheel Dozer Power Train Location of Power Train Components
C15 and C18 Engines for Caterpillar Built Machines Valve Actuator (Variable) - Remove
854K Wheel Dozer and 992K Wheel Loader Power Train MID 081 - CID 0444 - FMI 06
992K Wheel Loader Machine Systems Control Valve (Tilt Regeneration) - Remove
992K Wheel Loader Machine Systems Control Valve (Tilt Regeneration) - Install
992K Wheel Loader Machine Systems Control Valve (Tilt Regeneration) - Disassemble
992K Wheel Loader Machine Systems Control Valve (Tilt Regeneration) - Assemble
AD55B Underground Articulated Truck Power Train Drive Shaft (Upper) - Remove and Install
AD55B Underground Articulated Truck C27 Engine Supplement Bottom Guard (Engine) - Remove and Install
993K Wheel Loader Engine Supplement Engine - Remove
992K Wheel Loader and 854K Wheel Dozer Power Train Trunnion Support (Oscillating Axle, Front) - Remove
993K Wheel Loader Electrohydraulic System Piston Pump Margin Pressure (Hydraulic Fan) - Test and Adjust
994F Wheel Loader Pump Drive (Rear) from Engine - Separate
992K Wheel Loader and 854K Wheel Dozer Steering System Gear Pump (Steering Oil Cooler) (Steering Pilot)
2007/12/31 A New Calibration Procedure is Now Available {4269}