Tire and Rim (Rear) - Remove and Install
拆卸步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件描述     | 数量     |
A     | 155-3597     | 止轮块     | 4     |
B     | 9U-7536     | 起吊台架     | 2     |
4C-5809 | 液压泵     | 1     |
开始:
- 连接转向机架锁。 请参考拆解和组装, "转向机架锁 - 分离和连接"。
- 将铲斗或铲刀降至地面。
- 将工具 (A) 放置在前轮胎的前面和后面。
- 将适当的垫块 (2) 放在机器两侧的车桥壳 (3) 和后主机架 (1) 之间,如图所示。 这样可防止后桥壳摆动。
Show/hide table
不正确地支撑后桥壳体可能造成人身伤害。 后桥壳体的设计会出现振荡。 在拆卸和安装后轮胎和轮辋过程中,必须防止后桥壳体发生振荡。 将一个木块放置在后桥壳体与主机架之间,以防止后桥壳体发生振荡。 |
Show/hide table
图 1 | g00367854 |
- 如图所示,将工具 (B) 安置在后装载机机架的下面。 确保将工具 (B) 安置在机架纵梁下面。
Show/hide table
图 2 | g01444273 |
- 采用工具 (B) 抬起机器后部,使轮胎升离地面。
- 将工具 (B) 锁定到位。
- 拆下螺栓 (4) 和螺栓 (6) 。 拆下扶手 (8) 。
Show/hide table
图 3 | g01444283 |
- 拆下 4 个螺栓 (5) (未显示)。 拆下面板组件 (7) 。
- 将适当的起吊设备连接在轮胎和轮缘 (9) 上。
Show/hide table
图 4 | g01444298 |
- 从轮缘上拆下螺栓 (10) 。
- 采用适当的起吊设备小心地拆卸轮胎和轮缘 (9) 。 轮胎和轮缘 (9) 的组合重量可达 3856 kg (8500 lb)。
注: 拆卸轮胎和轮缘 (9) 时,注意不要损坏阀杆。
- 对后轮胎和轮缘 (9) 重复步骤 7 至 11。
安装步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件描述     | 数量     |
A     | 155-3597     | 止轮块     | 4     |
B     | 9U-7536     | 起吊台架     | 2     |
4C-5809 | 液压泵     | 1     | |
C     | 4C-5591     | 防粘结剂     | 1     |
注: 安装轮胎和轮缘前,确保轮缘组件和后部终传动的配合面清洁。
- 将适当的起吊设备连接在轮胎和轮缘 (9) 上。
Show/hide table
图 5 | g01444298 |
- 采用适当的起吊设备小心地安装轮胎和轮缘 (9) 。 轮胎和轮缘 (9) 的组合重量可达 3856 kg (8500 lb)。
注: 确保阀杆与终传动组件的槽口部分对齐。
- 将工具 (C) 涂抹在螺栓 (10) 上。 将螺栓 (10) 安装在轮缘中。 用 1150 ± 150N·m (850 ± 110 lb ft) 的扭矩拧紧螺栓 (10) 。
- 定位面板组件 (7) 。 拆下 4 个螺栓 (5) (未显示)。
Show/hide table
图 6 | g01444283 |
- 定位扶手 (8) 。 安装螺栓 (6) 和螺栓 (4) 。
- 对后轮胎和轮缘重复步骤 1 至 6。
- 将机器降至地面上。 拆下工具 (B) 。
Show/hide table
图 7 | g01444273 |
- 将工具 (A) 从前轮胎上拆下。
- 从机器两侧的车桥壳 (3) 和后主机架 (1) 之间拆卸适当的垫块 (2) 。
Show/hide table
图 8 | g00367854 |
End By: 分离转向机架锁。 请参考 拆解和组装, "转向机架锁 - 分离和连接"。
Caterpillar Information System:
992K Wheel Loader and 854K Wheel Dozer Power Train Tire and Rim (Front) - Remove and Install
The Transmission Mounting Bolts May Break {3082, 3253} The Transmission Mounting Bolts May Break {3082, 3253}
854K Wheel Dozer and 992K Wheel Loader Power Train MID 081 - CID 0144 - FMI 05
2008/09/29 A New Planetary Transmission Bolt That Improves Service Life Is Now Available {3030, 3064, 3105}
993K Wheel Loader Engine Supplement Turbocharger - Remove
993K Wheel Loader Engine Supplement Muffler - Remove and Install
2008/01/07 Improved Ride Control Check Valve for Medium Wheel Loaders {5051, 5067}
2008/02/04 A New Parking Brake Pressure Switch is Now Used {1408, 1435, 1435}
2008/05/19 An Improved Power Train Oil Pump Is Now Available {3066}
2008/05/05 An Improved Power Train Oil Pump Is Now Available {3066}
992K Wheel Loader and 854K Wheel Dozer Power Train Trunnion Support (Oscillating Axle, Rear) - Install
992K Wheel Loader and 854K Wheel Dozer Power Train Trunnion Support (Oscillating Axle, Rear) - Assemble
992K Wheel Loader and 854K Wheel Dozer Steering System Secondary Steering System - If Equipped
854K Wheel Dozer and 992K Wheel Loader Power Train MID 081 - CID 0144 - FMI 06
938H Wheel Loader and IT38H Integrated Toolcarrier Steering System Steering Cylinder
992K Wheel Loader and 854K Wheel Dozer Power Train Fixed Axle (Front) - Remove and Install
854K Wheel Dozer and 992K Wheel Loader Power Train MID 081 - CID 0168 - FMI 03
992K Wheel Loader and 854K Wheel Dozer Steering System Steering Control Valve (with Secondary Steering)
854K Wheel Dozer and 992K Wheel Loader Power Train MID 081 - CID 0168 - FMI 04
2007/12/31 Improved Venting is Now Used in the Fuel Tank {1273}
854K Wheel Dozer and 992K Wheel Loader Power Train MID 081 - CID 0177 - FMI 03
854K Wheel Dozer and 992K Wheel Loader Power Train MID 081 - CID 0177 - FMI 04
2008/01/28 The Rollover Protective Structure (ROPS) Group is Updated {7000, 7301, 7325}
854K Wheel Dozer and 992K Wheel Loader Power Train MID 081 - CID 0177 - FMI 08