844K and 854K Wheel Dozers and 990K, 992K, 993K, 994F and 994H Wheel Loaders Powered Access Stairway Caterpillar


MID 082 - CID 0350 - FMI 00

Usage:

854K 221
产生此代码的情况:


图 1g01440175

"提升连杆"位置传感器示意图

该诊断代码与"提升连杆"位置传感器相关。 FMI 00 诊断代码意味着 ECM 已确定传感器信号高于正常范围。

位置传感器的输出频率约为 500 Hz。 信号的工作负载循环随着位置传感器的移动而变化。

该诊断代码可能的原因如下:

  • 传感器需要重新标定。

  • ECM 出现故障。 这不太可能。

注: 以下测试步骤可能会生成其他诊断代码。 请忽略所产生的诊断代码,在排除原有诊断代码后清除即可。执行此步骤前,确保诊断代码 CID 0350 FMI 00 为激活状态。

注: 使用 146-4080 数字式万用表 进行本步骤中的测量。

系统响应:

该诊断代码将会记录在 ECM 的内部存储器中。

测试步骤 1. 检查传感器的调整和/或校准。

  1. 将断路开关和钥匙起动开关转到接通位置。

  1. 如有必要,执行位置传感器调整步骤。 执行位置传感器的校准。 有关这些步骤的更多信息,请参阅手册的测试和调整章节。

  1. 未将传感器或与传感器有关的硬件断开的情况下,使传感器在整个运动范围内移动。

    注: 在有些机器上,可能需要起动发动机来使传感器在整个运动范围内移动。

  1. 检查该诊断代码的状态。

预期结果:

CID 0350 FMI 00 诊断代码为未激活状态。

结果:

  • 正常 - 诊断代码处于未激活状态。 已通过调整和/或校准排除故障。 恢复正常运转。停止

  • 异常 - 诊断代码 CID 0350 FMI 00 仍为激活状态。

    修复: 退出本步骤。 重新执行本步骤。

    转至测试步骤 2。

测试步骤 2. 检查是否仍存在该诊断代码

  1. 检查线束接头并清洁机器线束接头的触点。

  1. 重新连接所有线束接头。

  1. 将断路开关和钥匙起动开关转到接通位置。

  1. 操作机器,使传感器在传感器整个工作范围内工作。

  1. 检查 CID 0350 FMI 00 诊断代码的状态。

预期结果:

在传感器的最大工作范围内,CID 0350 FMI 00 诊断代码为未激活状态。

结果:

  • 正常 - 在传感器的最大工作范围内,CID 0350 FMI 00 诊断代码为未激活状态。 此时不存在该诊断代码。 原有诊断代码可能是由于某个断开后重新连接的接头存在连接不良或短路引起的。 恢复正常运转。停止

  • 异常 - 在传感器的最大工作范围内,CID 0350 FMI 00 诊断代码为激活状态。 尚未修复该诊断代码。 ECM 可能出现故障。

    修复: ECM 不太可能会出现故障。 退出本步骤。 如有必要,执行传感器调整步骤。 然后执行传感器校准步骤。 重新执行本步骤。 如果没有找到故障原因,则需更换 ECM。 请参阅测试和调整, "ECM(Electronic Control Module,电子控制模块)- 更换"。

    停止

Caterpillar Information System:

992K Wheel Loader and 854K Wheel Dozer Braking System Piston Pump (Brake) Pressure - Test and Adjust
992K Wheel Loader and 854K Wheel Dozer Braking System Pump Performance (Brake) - Test
IT38H Integrated Toolcarrier and 938H Wheel Loader Operation Information
994F Wheel Loader Machine Systems Piston Pump (Steering) - Install
844K and 854K Wheel Dozers and 990K, 992K, 993K, 994F and 994H Wheel Loaders Powered Access Stairway MID 082 - CID 0296 - FMI 12
993K Wheel Loader Machine Systems Tilt Cylinder - Remove and Install
844K and 854K Wheel Dozers and 990K, 992K, 993K, 994F and 994H Wheel Loaders Powered Access Stairway MID 082 - CID 0296 - FMI 09
992K Wheel Loader Electrohydraulic System Lift Cylinder - Right Hand, Left Hand
Improvements To The Power Train Oil Pump{3066} Improvements To The Power Train Oil Pump{3066}
2008/09/29 A New Elbow is Now Used for the Rear Gear Train Oil Supply Lines {1204, 1206, 7517}
2008/04/14 Tooling for Machines with D8 SystemOne Undercarriage {0729, 4150}
Systems Operation Manual for the Axle Oil Cooler for the 990H Wheel Loader and the 844H Wheel Dozer{1365, 7620} Systems Operation Manual for the Axle Oil Cooler for the 990H Wheel Loader and the 844H Wheel Dozer{1365, 7620}
992K Wheel Loader and 854K Wheel Dozer Braking System Service Brake System Pressure - Test
844K and 854K Wheel Dozers and 990K, 992K, 993K, 994F and 994H Wheel Loaders Powered Access Stairway MID 082 - CID 0350 - FMI 01
844K and 854K Wheel Dozers and 990K, 992K, 993K, 994F and 994H Wheel Loaders Powered Access Stairway MID 082 - CID 0350 - FMI 08
992K Wheel Loader and 854K Wheel Dozer Braking System Service Brake Discs - Check
Procedure to Install the New Fuel Manifold and the Fuel Lines on Certain Caterpillar Machines{1250, 1251, 1261, 1274, 1702} Procedure to Install the New Fuel Manifold and the Fuel Lines on Certain Caterpillar Machines{1250, 1251, 1261, 1274, 1702}
992K Wheel Loader and 854K Wheel Dozer Braking System Parking Brake System Pressure - Test
844K and 854K Wheel Dozers and 990K, 992K, 993K, 994F and 994H Wheel Loaders Powered Access Stairway MID 082 - CID 0350 - FMI 13
992K Wheel Loader Electrohydraulic System MID 082 - CID 0351 - FMI 00
992K Wheel Loader Electrohydraulic System MID 082 - CID 0351 - FMI 01
992K Wheel Loader and 854K Wheel Dozer Braking System Parking Brake - Manual Release
992K Wheel Loader Electrohydraulic System MID 082 - CID 0351 - FMI 08
992K Wheel Loader Electrohydraulic System MID 082 - CID 0351 - FMI 13
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.